The Properties of Beryllium Copper Strip as Affected by Cold Rolling and Heat Treatment

Metals ◽  
1957 ◽  
pp. 143-156 ◽  
Author(s):  
J. T. Richards ◽  
Ellsworth M. Smith
Keyword(s):  
Heat Treatment ◽  
Cold Rolling ◽  
Copper Strip ◽  
Beryllium Copper

CONDULOY

Alloy Digest ◽  
1953 ◽  
Vol 2 (10) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Physical Properties ◽  
Tensile Properties ◽  
Copper Alloy ◽  
Heat Treating ◽  
Age Hardening ◽  
Beryllium Copper ◽  
Hardening Heat Treatment

Abstract CONDULOY is a low beryllium-copper alloy containing about 1.5% nickel. It responds to age-hardening heat treatment for improved mechanical properties. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on casting, heat treating, machining, and joining. Filing Code: Cu-11. Producer or source: Brush Beryllium Company.

BRUSH ALLOY 190

Alloy Digest ◽  
1968 ◽  
Vol 17 (12) ◽  
Keyword(s):  
Tensile Strength ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Surface Treatment ◽  
Tensile Properties ◽  
Heat Treating ◽  
Copper Strip ◽  
Beryllium Copper ◽  
Heat Treated

Abstract Brush Alloy 190 is a mill-heat treated beryllium copper strip with a tensile strength up to 190,000 psi. It eliminates the need of customer heat-treating by providing high properties combined with exceptional formability. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fatigue. It also includes information on corrosion resistance as well as forming, heat treating, joining, and surface treatment. Filing Code: Cu-194. Producer or source: Brush Beryllium Company.

Engineering mechanical properties by controlling the microstructure of an Fe–Ni–Mn martensitic steel through pre-cold rolling and subsequent heat treatment

2021 ◽  
Vol 804 ◽  
pp. 140760
Author(s):  
Hamidreza Koohdar ◽  
Pouya Hakimipour ◽  
Hamid Reza Jafarian ◽  
Terence G. Langdon ◽  
Mahmoud Nili-Ahmadabadi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cold Rolling ◽  
Martensitic Steel ◽  
Subsequent Heat Treatment

scholarly journals Analysis of the Crystallographic Microtexture of a UNS S32205 and a UNS S32304 Duplex Stainless Steels After Cold Rolling and Heat Treatment

2018 ◽  
Vol 21 (4) ◽  
Author(s):  
Karina Aparecida Martins Barcelos Gonçalves ◽  
Dagoberto Brandão Santos ◽  
Tarcísio Reis de Oliveira
Keyword(s):  
Heat Treatment ◽  
Cold Rolling ◽  
Stainless Steels ◽  
Duplex Stainless Steels

Role of Deformation Twinning in Cold Rolling and Recrystallization of Titanium

2005 ◽  
Vol 495-497 ◽  
pp. 651-656 ◽  
Author(s):  
Y.B. Chun ◽  
S. Lee Semiatin ◽  
Sun Keun Hwang
Keyword(s):  
Heat Treatment ◽  
Cold Rolling ◽  
Texture Component ◽  
Recrystallization Texture ◽  
Rolling Texture ◽  
Mechanical Twinning ◽  
Treatment Temperature ◽  
Recrystallization Annealing ◽  
Cp Ti ◽  
Evolution Of Microstructure

The evolution of microstructure and texture during cold rolling and recrystallization annealing of commercial-purity Ti (CP-Ti) was established. Cold rolling to 40% reduction activated mechanical twinning- mostly > 3 2 11 < } 2 2 11 { compressive twins and > 1 1 10 < } 2 1 10 { tensile twins. The formation of twins resulted in an inhomogeneous microstructure, in which only the localized regions containing twins were refined and the regions deformed by slip remained coarse. The twinned grains, containing high stored energy and numerous high-angle grain boundaries, became the preferential sites of nucleation during subsequent recrystallization. During recrystallization heat treatment at 500~700°C, the cold-rolling texture (ϕ1=0°, Φ=35°, ϕ2=30°) diminished in intensity, whereas a recrystallization texture component (ϕ1=15°, Φ=35°, ϕ2=35°) appeared. The recrystallization heat treatment temperature affected the rate of recrystallization but not the texture characteristics per se. During the subsequent grain growth stage, the recrystallization texture component increased. This behavior was attributed to the growth of larger-than-average grains of this particular crystal orientation.The evolution of microstructure and texture during cold rolling and recrystallization annealing of commercial-purity Ti (CP-Ti) was established. Cold rolling to 40% reduction activated mechanical twinning- mostly > 3 2 11 < } 2 2 11 { compressive twins and > 1 1 10 < } 2 1 10 { tensile twins. The formation of twins resulted in an inhomogeneous microstructure, in which only the localized regions containing twins were refined and the regions deformed by slip remained coarse. The twinned grains, containing high stored energy and numerous high-angle grain boundaries, became the preferential sites of nucleation during subsequent recrystallization. During recrystallization heat treatment at 500~700°C, the cold-rolling texture (ϕ1=0°, Φ=35°, ϕ2=30°) diminished in intensity, whereas a recrystallization texture component (ϕ1=15°, Φ=35°, ϕ2=35°) appeared. The recrystallization heat treatment temperature affected the rate of recrystallization but not the texture characteristics per se. During the subsequent grain growth stage, the recrystallization texture component increased. This behavior was attributed to the growth of larger-than-average grains of this particular crystal orientation.

Effect of Pre-Strain Rolling on Annealing Behavior of Friction-Stir Welded AA6061-T6 Aluminum Alloy

2018 ◽  
Vol 385 ◽  
pp. 355-358 ◽  
Author(s):  
Sergey Mironov ◽  
Sergey Malopheyev ◽  
Igor Vysotskiy ◽  
Daria Zhemchuzhnikova ◽  
Rustam Kaibyshev
Keyword(s):  
Heat Treatment ◽  
Thermal Stability ◽  
Aluminum Alloy ◽  
Cold Rolling ◽  
Grain Growth ◽  
Rolling Schedule ◽  
Annealing Behavior ◽  
Friction Stir ◽  
Welding Direction ◽  
Thermal Stability Of

In this work, the effect of pre-strain cold rolling on thermal stability of friction-stir welded AA6061-T6 alloy was studied. The pre-strain rolling was found to be very effective in suppression of abnormal grain growth during standard post-weld T6 heat treatment. It was also shown that the efficiency of this approach essentially depends on rolling path and the rolling along welding direction was the most effective rolling schedule.

Effects of Plastic Deformation, Heat Treatment and Molybdenum and Nickel Concentration on Lath Martensitic Microstructure

2017 ◽  
Vol 885 ◽  
pp. 222-227
Author(s):  
István Atanáz Hangyás ◽  
Enikő Réka Fábián ◽  
Tibor Berecz
Keyword(s):  
Heat Treatment ◽  
Plastic Deformation ◽  
Cold Rolling ◽  
Heat Treatments ◽  
Nickel Concentration ◽  
Chemical Compositions ◽  
Martensitic Microstructure

Lath martensitic microstructures were produced in steels containing 0.15% of carbon and various amounts of molybdenum and nickel. The behavior of the lath martensitic microstructure was studied during cold rolling in steels with six different chemical compositions. All materials have endured 75% deformation without damage. In addition, the effects of heat treatments on microstructures and hardness were investigated as well.

Sign in / Sign up

Export Citation Format

Share Document