Influence of Tread Polymer on Traction, Rolling Resistance, and Wear Properties of Tires

2009 ◽  
pp. 107-107-12
Author(s):  
IR Gelling
Keyword(s):  
Rolling Resistance ◽  
Wear Properties

scholarly journals Test Modes for Establishing the Tribological Profile under Slip-Rolling

Lubricants ◽  
2020 ◽  
Vol 8 (5) ◽  
pp. 59 ◽  
Author(s):  
Gregor Patzer ◽  
Mathias Woydt ◽  
Raj Shah ◽  
Curtis Miller ◽  
Philip Iaccarino
Keyword(s):  
Friction And Wear ◽  
Gear Tooth ◽  
Electrical Contact ◽  
Rolling Resistance ◽  
Rolling Contact ◽  
Hertzian Contact ◽  
Complex Nature ◽  
Wear Properties ◽  
Electrical Contact Resistance ◽  
Friction Temperature

The complex nature of slip-rolling contacts in many applications such as gear tooth flanks, rolling bearings, and heavy machinery often makes determining the friction and wear properties, as well as the fatigue resistance, of tribosystems difficult. The establishment of the tribological profile of a tribocouple under high Hertzian contact pressure and under slip-rolling will allow for the measurement and comparison of friction and wear coefficients as well as slip-rolling resistance by continuously monitoring the wear rate, coefficient of friction, temperature, oil film thickness, and/or electrical contact resistance using high-resolution signal analysis (HRA). A twin disc system can provide insight into the adhesive behavior of material and lubricant products such as alternative base oils and additives, ceramics, alloys, and thin film coatings. The strength and endurance of these products are often characterized through fatigue and resistance tests, which apply high Hertzian contact pressures to the rolling contact until seizure or failure is obtained. The further observation of the formation of tribofilms on the surface of contact yields information about the reactivity and thermochemical properties of additives. This review aims to illustrate how the implementation of different screening methodologies can be used as a meaningful tool for assessing the aforementioned tribological profile properties for the development of slip-rolling tribosystems.

MULTIPLE GLASS TRANSITION TERPOLYMERS OF ISOPRENE, BUTADIENE, AND STYRENE

2010 ◽  
Vol 83 (4) ◽  
pp. 380-390 ◽  
Author(s):  
Adel F. Halasa ◽  
Bill B. Gross ◽  
Wen-Liang Hsu
Keyword(s):  
Glass Transition ◽  
Loss Modulus ◽  
Rolling Resistance ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Transition Temperatures ◽  
Wear Properties ◽  
Glass Transition Temperatures ◽  
The One ◽  
Butadiene Styrene

Abstract Novel polymers that will contribute to a better combination of traction and tread wear in tire applications, which is historically difficult to achieve, have been developed. In this work, multiple viscoelastic polymers possessing multiple glass transition temperatures terpolymers of isoprene/butadiene/styrene were synthesized containing 45/45/10, 40/40/20, and 35/35/30 polymer ratios in 5-gallon laboratory reactors using tetramethylethylenediamine or bis(dipiperdino) ethane as a modifier. These polymers show two glass transition temperatures (Tg's); the one that occurs at higher temperatures (–25 to –10 °C) is known to contribute to good wet traction properties, while the lower Tg is known to contribute to better tread wear properties. These terpolymers were characterized by the fact that their multiviscoelastic loss modulus has narrow molecular distribution for better rolling resistance. In a standard ASTM D31912 carbon-black-filled tread compound recipe, the polymers having all three terpolymers of isoprene/butadiene/styrene polymerized showed excellent values of loss tangent at 0 and 60 ºC, which is a laboratory predictor for both wet traction and rolling resistance. These terpolymers when evaluated in the same ASTM D3191 delivered better properties in a tread compound recipe than either solution or emulsion styrene-butadiene rubber in a formulation that has natural rubber or polybutadiene.

Extraction and identification of fillers and pigments from pyrolyzed rubber and tire samples

1996 ◽  
Vol 54 ◽  
pp. 174-175
Author(s):  
P. Sadhukhan ◽  
J. B. Zimmerman
Keyword(s):  
Zinc Oxide ◽  
Electron Microscope ◽  
Carbon Black ◽  
Natural Rubber ◽  
Transmission Electron Microscope ◽  
Rolling Resistance ◽  
Synthetic Polymers ◽  
Nitrogen Atmosphere ◽  
Transmission Electron ◽  
Curing Agents

Rubber stocks, specially tires, are composed of natural rubber and synthetic polymers and also of several compounding ingredients, such as carbon black, silica, zinc oxide etc. These are generally mixed and vulcanized with additional curing agents, mainly organic in nature, to achieve certain “designing properties” including wear, traction, rolling resistance and handling of tires. Considerable importance is, therefore, attached both by the manufacturers and their competitors to be able to extract, identify and characterize various types of fillers and pigments. Several analytical procedures have been in use to extract, preferentially, these fillers and pigments and subsequently identify and characterize them under a transmission electron microscope.Rubber stocks and tire sections are subjected to heat under nitrogen atmosphere to 550°C for one hour and then cooled under nitrogen to remove polymers, leaving behind carbon black, silica and zinc oxide and 650°C to eliminate carbon blacks, leaving only silica and zinc oxide.

Influence of Multiwall Carbon Nanotube on mechanical and wear properties of Copper – Iron composite

2020 ◽  
Vol 17 (1) ◽  
pp. 7570-7576 ◽  
Author(s):  
H. Sh. Hammood ◽  
S. S. Irhayyim ◽  
A. Y. Awad ◽  
H. A. Abdulhadi
Keyword(s):  
Carbon Nanotubes ◽  
Volume Fraction ◽  
Hybrid Composites ◽  
Hydraulic Press ◽  
Dry Sliding Wear ◽  
Multiwall Carbon Nanotube ◽  
Wear Properties ◽  
Sem Images ◽  
Wear Rates ◽  
Multiwall Carbon

Multiwall Carbon nanotubes (MWCNTs) are frequently attractive due to their novel physical and chemical characteristics, as well as their larger aspect ratio and higher conductivity. Therefore, MWCNTs can allow tremendous possibilities for the improvement of the necessarily unique composite materials system. The present work deals with the fabrication of Cu-Fe/CNTs hybrid composites manufactured by powder metallurgy techniques. Copper powder with 10 vol. % of iron powder and different volume fractions of Multi-Wall Carbon Nanotubes (MWCNTs) were mixed to get hybrid composites. The hybrid composites were fabricated by adding 0.3, 0.6, 0.9, and 1.2 vol.% of MWCNTs to Cu- 10% Fe mixture using a mechanical mixer. The samples were compressed under a load of 700 MPa using a hydraulic press to compact the samples. Sintering was done at 900°C for 2 h at 5ºC/min heating rate. The microscopic structure was studied using a Scanning Electron Microscope (SEM). The effect of CNTs on the mechanical and wear properties, such as micro-hardness, dry sliding wear, density, and porosity were studied in detail. The wear tests were carried out at a fixed time of 20 minutes while the applied loads were varied (5, 10, 15, and 20 N). SEM images revealed that CNTs were uniformly distributed with relative agglomeration within the Cu/Fe matrix. The results showed that the hardness, density, and wear rates decreased while the percentage of porosity increased with increasing the CNT volume fraction. Furthermore, the wear rate for all the CNTs contents increased with the applied load.

Tire-Road Interactions — Harmony or Conflict?

1989 ◽  
Vol 17 (1) ◽  
pp. 66-84
Author(s):  
A. R. Williams
Keyword(s):  
Rolling Resistance ◽  
Major Effect ◽  
Road Surface ◽  
Interactive Effects ◽  
Central Theme ◽  
Water Drainage ◽  
The Road ◽  
Truck Tires ◽  
Road Surfaces ◽  
Tire Wear

Abstract This is a summary of work by the author and his colleagues, as well as by others reported in the literature, that demonstrate a need for considering a vehicle, its tires, and the road surface as a system. The central theme is interaction at the footprint, especially that of truck tires. Individual and interactive effects of road and tires are considered under the major topics of road aggregate (macroscopic and microscopic properties), development of a novel road surface, safety, noise, rolling resistance, riding comfort, water drainage by both road and tire, development of tire tread compounds and a proving ground, and influence of tire wear on wet traction. A general conclusion is that road surfaces have both the major effect and the greater potential for improvement.

Tread Depth Effects on Tire Rolling Resistance

2001 ◽  
Vol 29 (3) ◽  
pp. 134-154 ◽  
Author(s):  
J. R. Luchini ◽  
M. M. Motil ◽  
W. V. Mars
Keyword(s):  
Finite Element Analysis ◽  
Common Knowledge ◽  
Rolling Resistance ◽  
Test Method ◽  
Tire Model ◽  
Element Analysis ◽  
Truck Tires ◽  
The Finite Element Analysis ◽  
Equilibrium Test ◽  
Depth Effects

Abstract This paper discusses the measurement and modeling of tire rolling resistance for a group of radial medium truck tires. The tires were subjected to tread depth modifications by “buffing” the tread surface. The experimental work used the equilibrium test method of SAE J-1269. The finite element analysis (FEA) tire model for tire rolling resistance has been previously presented. The results of the testing showed changes in rolling resistance as a function of tread depth that were inconsistent between tires. Several observations were also inconsistent with published information and common knowledge. Several mechanisms were proposed to explain the results. Additional experiments and models were used to evaluate the mechanisms. Mechanisms that were examined included tire age, surface texture, and tire shape. An explanation based on buffed tread radius, and the resulting changes in footprint stresses, is proposed that explains the observed experimental changes in rolling resistance with tread depth.

Application of Computational Mechanics to Tire Design—Yesterday, Today, and Tomorrow

2011 ◽  
Vol 39 (4) ◽  
pp. 223-244 ◽  
Author(s):  
Y. Nakajima
Keyword(s):  
Finite Element ◽  
New Technologies ◽  
Computational Mechanics ◽  
Design Procedure ◽  
Side Wall ◽  
Rolling Resistance ◽  
Optimization Techniques ◽  
Stress Strain ◽  
Element Analysis ◽  
Crown Shape

Abstract The tire technology related with the computational mechanics is reviewed from the standpoint of yesterday, today, and tomorrow. Yesterday: A finite element method was developed in the 1950s as a tool of computational mechanics. In the tire manufacturers, finite element analysis (FEA) was started applying to a tire analysis in the beginning of 1970s and this was much earlier than the vehicle industry, electric industry, and others. The main reason was that construction and configurations of a tire were so complicated that analytical approach could not solve many problems related with tire mechanics. Since commercial software was not so popular in 1970s, in-house axisymmetric codes were developed for three kinds of application such as stress/strain, heat conduction, and modal analysis. Since FEA could make the stress/strain visible in a tire, the application area was mainly tire durability. Today: combining FEA with optimization techniques, the tire design procedure is drastically changed in side wall shape, tire crown shape, pitch variation, tire pattern, etc. So the computational mechanics becomes an indispensable tool for tire industry. Furthermore, an insight to improve tire performance is obtained from the optimized solution and the new technologies were created from the insight. Then, FEA is applied to various areas such as hydroplaning and snow traction based on the formulation of fluid–tire interaction. Since the computational mechanics enables us to see what we could not see, new tire patterns were developed by seeing the streamline in tire contact area and shear stress in snow in traction.Tomorrow: The computational mechanics will be applied in multidisciplinary areas and nano-scale areas to create new technologies. The environmental subjects will be more important such as rolling resistance, noise and wear.

Rolling Resistance Calculation Procedure Using the Finite Element Method

2019 ◽  
Vol 48 (3) ◽  
pp. 224-248
Author(s):  
Pablo N. Zitelli ◽  
Gabriel N. Curtosi ◽  
Jorge Kuster
Keyword(s):  
Finite Element ◽  
Energy Dissipation ◽  
Rolling Resistance ◽  
Element Model ◽  
The Finite Element Method ◽  
Temperature Changes ◽  
Rubber Compounds ◽  
Different Temperatures ◽  
Materials Used ◽  
Account Temperature

ABSTRACT Tire engineers are interested in predicting rolling resistance using tools such as numerical simulation and tests. When a car is driven along, its tires are subjected to repeated deformation, leading to energy dissipation as heat. Each point of a loaded tire is deformed as the tire completes a revolution. Most energy dissipation comes from the cyclic loading of the tire, which causes the rolling resistance in addition to the friction force in the contact patch between the tire and road. Rolling resistance mainly depends on the dissipation of viscoelastic energy of the rubber materials used to manufacture the tires. To obtain a good rolling resistance, the calculation method of the tire finite element model must take into account temperature changes. It is mandatory to calibrate all of the rubber compounds of the tire at different temperatures and strain frequencies. Linear viscoelasticity is used to model the materials properties and is found to be a suitable approach to tackle energy dissipation due to hysteresis for rolling resistance calculation.

Formation of Standing Waves in Radial Tires

1984 ◽  
Vol 12 (1) ◽  
pp. 44-63 ◽  
Author(s):  
Y. D. Kwon ◽  
D. C. Prevorsek
Keyword(s):  
High Speed ◽  
Critical Speed ◽  
Unit Length ◽  
Standing Waves ◽  
Rolling Resistance ◽  
Damping Coefficient ◽  
Circular Membrane ◽  
Critical Speeds ◽  
Steel Cord ◽  
The Individual

Abstract Radial tires for automobiles were subjected to high speed rolling under load on a testing wheel to determine the critical speeds at which standing waves started to form. Tires of different makes had significantly different critical speeds. The damping coefficient and mass per unit length of the tire wall were measured and a correlation between these properties and the observed critical speed of standing wave formation was sought through use of a circular membrane model. As expected from the model, desirably high critical speed calls for a high damping coefficient and a low mass per unit length of the tire wall. The damping coefficient is particularly important. Surprisingly, those tire walls that were reinforced with steel cord had higher damping coefficients than did those reinforced with polymeric cord. Although the individual steel filaments are elastic, the interfilament friction is higher in the steel cords than in the polymeric cords. A steel-reinforced tire wall also has a higher density per unit length. The damping coefficient is directly related to the mechanical loss in cyclic deformation and, hence, to the rolling resistance of a tire. The study shows that, in principle, it is more difficult to design a tire that is both fuel-efficient and free from standing waves when steel cord is used than when polymeric cords are used.

Evolving the Banded Radial Tire

1987 ◽  
Vol 15 (1) ◽  
pp. 30-41 ◽  
Author(s):  
E. G. Markow
Keyword(s):  
Finite Element ◽  
Wear Rate ◽  
Finite Element Modeling ◽  
Laboratory Tests ◽  
Rolling Resistance ◽  
Two Dimensional ◽  
Theoretical Discussion ◽  
Radial Tire ◽  
Puncture Resistance ◽  
Element Modeling

Abstract Development of the banded radial tire is discussed. A major contribution of this tire design is a reliable run-flat capability over distances exceeding 160 km (100 mi). Experimental tire designs and materials are considered; a brief theoretical discussion of the mechanics of operation is given based on initial two-dimensional studies and later on more complete finite element modeling. Results of laboratory tests for cornering, rolling resistance, and braking are presented. Low rolling resistance, good cornering and braking properties, and low tread wear rate along with good puncture resistance are among the advantages of the banded radial tire designs.

Sign in / Sign up

Export Citation Format

Share Document