Tire-Road Interactions — Harmony or Conflict?

1989 ◽  
Vol 17 (1) ◽  
pp. 66-84
Author(s):  
A. R. Williams
Keyword(s):  
Rolling Resistance ◽  
Major Effect ◽  
Road Surface ◽  
Interactive Effects ◽  
Central Theme ◽  
Water Drainage ◽  
The Road ◽  
Truck Tires ◽  
Road Surfaces ◽  
Tire Wear

Abstract This is a summary of work by the author and his colleagues, as well as by others reported in the literature, that demonstrate a need for considering a vehicle, its tires, and the road surface as a system. The central theme is interaction at the footprint, especially that of truck tires. Individual and interactive effects of road and tires are considered under the major topics of road aggregate (macroscopic and microscopic properties), development of a novel road surface, safety, noise, rolling resistance, riding comfort, water drainage by both road and tire, development of tire tread compounds and a proving ground, and influence of tire wear on wet traction. A general conclusion is that road surfaces have both the major effect and the greater potential for improvement.

scholarly journals Laboratory experiment on the nano-TiO2 photocatalytic degradation effect of road surface oil pollution

2020 ◽  
Vol 9 (1) ◽  
pp. 922-933
Author(s):  
Qing’e Wang ◽  
Kai Zheng ◽  
Huanan Yu ◽  
Luwei Zhao ◽  
Xuan Zhu ◽  
...  
Keyword(s):  
Photocatalytic Degradation ◽  
Oil Pollution ◽  
Road Surface ◽  
Test Method ◽  
Driving Safety ◽  
The Road ◽  
Road Surfaces ◽  
The Many ◽  
The Impact ◽  
Degradation Effect

AbstractOil leak from vehicles is one of the most common pollution types of the road. The spilled oil could be retained on the surface and spread in the air voids of the road, which results in a decrease in the friction coefficient of the road, affects driving safety, and causes damage to pavement materials over time. Photocatalytic degradation through nano-TiO2 is a safe, long-lasting, and sustainable technology among the many methods for treating oil contamination on road surfaces. In this study, the nano-TiO2 photocatalytic degradation effect of road surface oil pollution was evaluated through the lab experiment. First, a glass dish was used as a substrate to determine the basic working condition of the test; then, a test method considering the impact of different oil erosion degrees was proposed to eliminate the effect of oil erosion on asphalt pavement and leakage on cement pavement, which led to the development of a lab test method for the nano-TiO2 photocatalytic degradation effect of oil pollution on different road surfaces.

A new procedure for determining the road surface reduced luminance coefficient table by on-site measurements

2018 ◽  
Vol 51 (1) ◽  
pp. 65-81 ◽  
Author(s):  
N Strbac-Hadzibegovic ◽  
S Strbac-Savic ◽  
M Kostic
Keyword(s):  
Road Surface ◽  
Surface Reflection ◽  
The Road ◽  
Road Lighting ◽  
Average Luminance ◽  
Road Surfaces ◽  
Q Values

Numerous measurements have shown that the standard R classes do not represent adequately many road surfaces used nowadays. Therefore, the construction of portable reflectometers intended for on-site measurements of road surface reflection properties has been given particular attention during the last decade. This paper presents a new procedure for the improvement of the accuracy of such a portable reflectometer. Optimally extrapolating the values of the 20 luminance coefficients (q), each measured by the portable reflectometer for a set of angles of observation (α = 5°–80°), the 20 q-values referring to α = 1° are calculated. This enables their comparison with the corresponding q elements from each of the 447 reduced q-tables derived from the available r-table database, obtained by using a precise laboratory reflectometer on a wide variety of road samples. Selecting the closest reduced q-table, the corresponding r-table and the actual average luminance coefficient can be determined. In order to validate the proposed procedure, which can also be applied to other similar portable reflectometers, measurements of the luminance and overall and longitudinal luminance uniformities were carried out on eleven road-lighting installations. They showed that the results obtained by this procedure deviate only slightly from those obtained using r-tables determined by the laboratory reflectometer.

Observations on the Physical Aspects of Resistance to Skidding on Dry Roads and Particularly on Wet Roads

1956 ◽  
Vol 29 (4) ◽  
pp. 1425-1433 ◽  
Author(s):  
K. Knauerhase
Keyword(s):  
Great Influence ◽  
Boundary Surface ◽  
Road Surface ◽  
Motor Vehicles ◽  
Vector Diagram ◽  
Surface Adhesion ◽  
The Road ◽  
Wet Friction ◽  
Road Surfaces ◽  
Wetting Power

Abstract To ensure safety from skidding, attention has up to now been devoted to building rough surface roads, to the development of the proper vehicle construction with respect to this feature, and to the factor most directly involved, the tires. Special attention has been directed in connection with this latter phase to a much more open tread patterning and to the effect of decreasing tire inflation, both of which affect the life of the tire adversely. These steps neglected to take advantage of the physical effect of adhesion, which, without lowering the durability, now makes possible an enhanced contribution to the cohesive friction by the profile grooves which are of necessity retained to keep the weight down. The goal is, therefore, to provide the smooth surfaces of the tread pattern that come in contact with the road with the greatest possible physical gripping power, or adhesion. After illustrating the interfacial magnitudes with the help of a vector diagram, we shall survey the laws of boundary surface adhesion. Here the great influence of the liquid involved in wet friction becomes clear and the particularly favorable interfacial tension property of water can be assessed. Since skidding can occur only at the interfaces : rubber-water, or water-road, the requirement is as follows : both the greatest possible wetting power between rubber and water, and also between water and road surface, that is, hydrophilic properties in the rubber and hydrophilic road surfaces, in order to reduce the danger of skidding. Good insurance against skidding requires hydrophilic rubber and a hydrophilic road surface, for a tire that has been developed to be nonskidding holds on a hydrophilic road surface and skids on a hydrophobic road surface. A hydrophobic tire, on the other hand, skids on any wet road. Although considerable advances have been made with respect to safety from skidding since rubber tires were first developed for motor vehicles, with increase of speeds this problem demands our attention to a greater and greater degree. Safety from skidding can result only from the combined efforts of road and car builders, tire makers, and the chemists and physicists of all three groups.

scholarly journals EXAMINATION OF TRUCK TIRES AS TO IDENTIFICATION OF DAMAGES WHICH ARE FORMED AS A RESULT OF OPERATIONAL TIRE WEAR OR PRODUCT DEFECT

2020 ◽  
Vol 21 (1) ◽  
pp. 441-451
Author(s):  
A. Frolov ◽  
O. Shabratko
Keyword(s):  
Road Surface ◽  
Specific Pressure ◽  
Dynamic Impact ◽  
Tire Pressure ◽  
General Increase ◽  
The Road ◽  
Truck Tires ◽  
On The Road ◽  
Product Defect ◽  
External Inspection

The sequence of carrying out of researches of tires of a freight vehicle on the basis of expert practice is considered. The research of tires of a truck has been conducted, an example of an expert research of tires is resulted, as a result of which the causes of damage of tires were established. The tire connects the vehicle to the road, perceives its weight, braking effort and dynamic impact that arises due to the roughness of the road surface. It is not uncommon for the vehicle to operate even on roads with a satisfactory road surface and damage to the tires. Damage to the tires can be generated as a result of industrial damage (factory defect) and as a result of operational damage. The most common and serious cause of premature wear and damage to tires is non-compliance with the established air pressure norms and overload tires. Changing the configuration of the profile and increasing the deformation of the bus cause an increase in the voltage in its material. As a result, it increases its premature wear. At increased load (overload) the tension voltage in the places of contact of the tire with the road increases and its specific pressure on the road, from which the tread wears away more quickly. Overvoltage in the material and increase in deformation is accompanied by a general increase in friction and heat formation in the tire. At increased load (overload) the tension voltage in the places of contact of the tire with the road increases and its specific pressure on the road, from which the tread wears away more quickly. Overvoltage in the material and increase in deformation is accompanied by a general increase in friction and heat formation in the tire. In the course of the research it was established that the tires Satoya SD 062-III have operational damage, the detects damage to the tires was formed as a result of their operation, which could contribute to vehicle overload, non compliance with tire pressure and the movement of the vehicle on roads with improper road surface. External inspection the examination of Satoya SD 062-III tires showed no signs of industrial damage (factory defects).

scholarly journals Perceiving Excitation Characteristics from Interactions between Field Road and Vehicle via Vibration Sensing

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Yuansheng Cheng ◽  
Xiaoqin Li ◽  
Xiaolan Man ◽  
Feifan Fan ◽  
Zhixiong Li
Keyword(s):  
Vibration Response ◽  
Road Surface ◽  
Vibration Test ◽  
Agricultural Vehicles ◽  
The Road ◽  
Effective Roughness ◽  
Long Wave ◽  
Road Surfaces ◽  
Road Excitation ◽  
Wave Surfaces

When agricultural vehicles operate in the field, the soft road excitation makes it difficult to measure the vehicle vibration. A camera-accelerator system can solve this issue by utilizing computer vision information; however, the relationship between the field road surface and the vehicle vibration response remains an unsolved problem. This study aims to investigate the correlation of the soft road excitation of different long-wave surfaces with the vehicle vibration response. Vibration equation between the vehicle and soft road surface system was established to produce an effective roughness model of the field soft road surface. In order to simulate the vehicle vibration state under different long-wave road surfaces, the soil rectangular pits with 21 kinds of different spans and depths were applied to the road surfaces, and a tractor vibration test system was built for vibration test. The frequency spectrum analysis was performed for the vibration response and the roughness signals of the road surfaces. The results showed that coefficient (R2) of frequency correlation between the roughness excitation and the original unevenness at the excitation point at the rear end of the rectangular soil pit fell within 0.9641∼0.9969. The main frequency band of the vibration response fell within 0∼3 Hz, and the phenomenon of quadruple frequency existed. The correlation of roughness excitation with quadruple frequency fell within 0.992165∼1. The primary excitation points were located at the rear end of the rectangular soil pit. In addition, it also indicated that when the vehicle was driven without autonomous power, the vehicle vibration frequency mainly depended on the excitation frequency of the field road surface and the frequency at the maximum vehicle vibration intensity was 2 or 3 times of that at the maximum field soft road excitation. These findings may provide a reference for optimal design of vibration reduction and control for agricultural vehicles.

scholarly journals DESTROYING EFFECTS OF TRUCK TIRES ON THE DESIGN OF ROADWEAR

2022 ◽  
Vol 1 (1) ◽  
pp. 63-71
Author(s):  
Vladimir Pryadkin ◽  
Artem Artemov ◽  
Pavel Kolyadin ◽  
A. Kolcov
Keyword(s):  
Mathematical Model ◽  
Road Surface ◽  
Destructive Effect ◽  
The Road ◽  
Truck Tires ◽  
Temperature State ◽  
On The Road ◽  
The Mathematical Model

The article presents a mathematical model of the destructive effect of a wide-profile tire on the roadway. The mathematical model makes it possible to adequately reproduce the effect of a wide-profile tire on the road surface, taking into account the load and parameters of the tire, as well as the structure of the road surface and the temperature state.

On the applicability of a scan-based mobile mapping system for monitoring the planarity and subsidence of road surfaces – Pilot study on the A44n motorway in Germany

2020 ◽  
Vol 14 (1) ◽  
pp. 39-54 ◽  
Author(s):  
Erik Heinz ◽  
Christian Eling ◽  
Lasse Klingbeil ◽  
Heiner Kuhlmann
Keyword(s):  
Standard Deviation ◽  
Point Clouds ◽  
Road Surface ◽  
Control Points ◽  
Mobile Mapping ◽  
The Road ◽  
Mapping System ◽  
Road Surfaces ◽  
Mobile Mapping System ◽  
Physical Height

AbstractKinematic laser scanning is widely used for the fast and accurate acquisition of road corridors. In this context, road monitoring is a crucial application, since deficiencies of the road surface due to non-planarity and subsidence put traffic at risk. In recent years, a Mobile Mapping System (MMS) has been developed at the University of Bonn, consisting of a GNSS/IMU unit and a 2D laser scanner. The goal of this paper is to evaluate the accuracy and precision of this MMS, where the height component is of main interest. Following this, the applicability of the MMS for monitoring the planarity and subsidence of road surfaces is analyzed. The test area for this study is a 6 km long section of the A44n motorway in Germany. For the evaluation of the MMS, leveled control points along the motorway as well as point cloud comparisons of repeated passes were used. In order to transform the ellipsoidal heights of the MMS into the physical height system of the control points, undulations were utilized. In this respect, a local tilt correction for the geoid model was determined based on GNSS baselines and leveling, leading to a physical height accuracy of the MMS of < 10 mm (RMS). The related height precision has a standard deviation of about 5 mm. Hence, a potential subsidence of the road surface in the order of a few cm is detectable. In addition, the point clouds were used to analyze the planarity of the road surface. In the course of this, the cross fall of the road was estimated with a standard deviation of < 0.07 %. Yet, no deficiencies of the road surface in the form of significant rut depths or fictive water depths were detected, indicating the proper condition of the A44n motorway. According to our tests, the MMS is appropriate for road monitoring.

Road Surface Bulk Water Drainage—A Theoretical Study

1978 ◽  
Vol 6 (2) ◽  
pp. 125-158 ◽  
Author(s):  
R. Bond ◽  
G. Lees
Keyword(s):  
Theoretical Approach ◽  
Theoretical Study ◽  
Aggregate Size ◽  
Bulk Water ◽  
Road Surface ◽  
Minimum Time ◽  
Water Drainage ◽  
The Road

Abstract A theoretical approach to bulk water drainage properties at the tire/road surface interface for a freely rotating tire is presented. The results show that it is possible to optimize the road surface macrotexture conditions (aggregate size, aggregate spacing, and absolute texture depth) to give the minimum time for removal of bulk water from the interface yet give the maximum possible actual area of contact between the tire and road surface to obtain the maximum possible friction levels.

Research on the Effectiveness of Water Drainage from Concrete Road Surfaces Depending on the Texture Parameters

2014 ◽  
Vol 1020 ◽  
pp. 86-91
Author(s):  
Marlena Rajczyk ◽  
Zbigniew Respondek
Keyword(s):  
Surface Texture ◽  
Concrete Surface ◽  
Road Surface ◽  
Water Drainage ◽  
Texture Parameters ◽  
Road Surfaces ◽  
Surface Inclination

The article presents ways of constructing concrete road surface built with the polygon technology. It discusses ways of finishing the texture of the surface to obtain proper anti-skidding properties. It presents the results of research on the influence of various concrete surface texture parameters and surface inclination to the horizontal on the effectiveness and the rate of rainwater drainage.

SILICA-REINFORCED EPOXIDIZED NATURAL RUBBER TIRE TREADS — PERFORMANCE AND DURABILITY

2015 ◽  
Vol 88 (3) ◽  
pp. 390-411 ◽  
Author(s):  
Pamela J. Martin ◽  
Paul Brown ◽  
Andrew V. Chapman ◽  
Stuart Cook
Keyword(s):  
Environmental Impact ◽  
Natural Rubber ◽  
Fossil Fuel ◽  
Rolling Resistance ◽  
Epoxidized Natural Rubber ◽  
Research Centre ◽  
Wear Performance ◽  
The Road ◽  
Tire Wear ◽  
On The Road

ABSTRACT Concerns regarding climate change and public health have compelled governments to reduce the environmental impact of transport. Many countries are introducing tire labeling and legislation targeting rolling resistance, wet grip, and noise. The proposed U.S. tire label also includes wear performance. Implementation of tire labeling is enabling buyers to choose better tires. The tire industry is responding to these demands and is developing the next generation of green tires. Current passenger tire tread technology is primarily petroleum based; however, the long-term availability of fossil-fuel supplies is limited. Thus a further step to minimize the environmental impact and carbon footprint of tires over their life cycle is to use sustainable materials not derived from fossil-fuels. Sumitomo Rubber Industries used epoxidized natural rubber (ENR) reinforced with silica in their route to a greener fossil-fuel free tire (the ENASAVE 100). At 25 mol% epoxidation, ENR has a glass transition temperature (Tg) most suitable for tread applications. Silica-filled ENR-25 tread compounds deliver lower rolling resistance, hence reduced fuel consumption, and enhanced wet and ice traction compared with benchmark premium passenger or truck treads. Optimization of wear performance to extend product durability is a current focus of research. However, correlation between laboratory abrasion and on-the-road tire wear is notoriously poor. The Tun Abdul Razak Research Centre (TARRC) have used light microscopy and transmission electron microscopy (TEM) to ascertain a mechanistic insight into tread wear, using results from wear studies on-the-road and laboratory abrasion. The results indicate that the mechanism of on-the-road tire wear differs from that of in-laboratory Akron abrasion tests.

Sign in / Sign up

Export Citation Format

Share Document