Failure of Stainless Steel Check Valve in Oxygen Service

2009 ◽  
pp. 53-53-5 ◽  
Author(s):  
JJ Rago
Keyword(s):  
Stainless Steel ◽  
Check Valve

Design and Fabrication of the Piezoelectrically Actuated Micropump with Implanted Check Valves

2013 ◽  
Vol 284-287 ◽  
pp. 2032-2036
Author(s):  
Chiang Ho Cheng ◽  
Yi Pin Tseng
Keyword(s):  
Stainless Steel ◽  
Flow Rate ◽  
Steel Substrate ◽  
Check Valve ◽  
Maximum Flow ◽  
Mems Fabrication ◽  
Sinusoidal Waveform ◽  
Nickel Electroforming ◽  
Bridge Type ◽  
Type Check

This paper aims to present the design, fabrication and test of a novel piezoelectrically actuated, check valve embedded micropump having the advantages of miniature size, light weight and low power consumption. The micropump consists of a piezoelectric actuator, a stainless steel chamber layer with membrane, two stainless steel channel layers with two valve seats, and a nickel check valve layer with two bridge-type check valves. The check valve layer was fabricated by nickel electroforming process on a stainless steel substrate. The chamber and the channel layer were made of the stainless steel manufactured using the lithography and etching process based on MEMS fabrication technology. The effects of check valve thickness, operating frequency and back pressure on the flow rate of the micropump are investigated. The micropump with check valve 20 μm in thickness obtained higher output values under the sinusoidal waveform of 120 Vpp and 160 Hz. The maximum flow rate and backpressure are 1.82 ml/min and 32 kPa, respectively.

Comparison of Texas Liquid Sampler with Missouri Bottle for Sampling Liquid Fertilizers: Collaborative Study

1993 ◽  
Vol 76 (4) ◽  
pp. 749-753
Author(s):  
George W Latimer ◽  
◽  
J Comstock ◽  
D Dubberly ◽  
T Jessup ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Total Nitrogen ◽  
Collaborative Study ◽  
Check Valve ◽  
Sampling Procedure ◽  
Available Phosphorus ◽  
Liquid Sample ◽  
Polyethylene Tube ◽  
Sampling Tube ◽  
Liquid Sampling

Abstract Six laboratories participated in a collaborative study designed to qualify the Texas liquid sampling tube as a device for sampling liquid fertilizers. The Texas sampler is a polyethylene tube with a stainless steel check valve on one end. The tube, which is threaded so that it can be expanded in length, enables acquisition of a uniform profile across a liquid sample. The 6 collaborators sampled 33 loads of fertilizer, 8 of which were slurries, using both the Texas tube and the Missouri bottle (AOAC 969.01). The resulting subsamples were analyzed for total nitrogen, available phosphorus, and soluble potash. Analysis of the data showed no significant (p < 0.05) difference in results. This sampling procedure, using the Texas liquid sampler, was adopted first action by AOAC International as a suitable means of sampling liquid fertilizers.

Development of a stainless steel check valve for cryogenic applications

Cryogenics ◽  
2007 ◽  
Vol 47 (2) ◽  
pp. 121-126 ◽  
Author(s):  
T.T. Veenstra ◽  
G.C.F. Venhorst ◽  
J.F. Burger ◽  
H.J. Holland ◽  
H.J.M. ter Brake ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Check Valve

NiAl precipitation in Fe-12w/o Cr-5w/o Ni-4w/o Al

1983 ◽  
Vol 41 ◽  
pp. 202-203
Author(s):  
L.E. Murr ◽  
J.S. Dunning ◽  
S. Shankar
Keyword(s):  
Solid Solution ◽  
Stainless Steel ◽  
Stainless Steels ◽  
Alloy Composition ◽  
Chromium Content ◽  
Scale Up ◽  
Optical Metallography ◽  
Property Evaluation ◽  
310 Stainless Steel ◽  
Microstructural Studies

Aluminum additions to conventional 18Cr-8Ni austenitic stainless steel compositions impart excellent resistance to high sulfur environments. However, problems are typically encountered with aluminum additions above about 1% due to embrittlement caused by aluminum in solid solution and the precipitation of NiAl. Consequently, little use has been made of aluminum alloy additions to stainless steels for use in sulfur or H2S environments in the chemical industry, energy conversion or generation, and mineral processing, for example.A research program at the Albany Research Center has concentrated on the development of a wrought alloy composition with as low a chromium content as possible, with the idea of developing a low-chromium substitute for 310 stainless steel (25Cr-20Ni) which is often used in high-sulfur environments. On the basis of workability and microstructural studies involving optical metallography on 100g button ingots soaked at 700°C and air-cooled, a low-alloy composition Fe-12Cr-5Ni-4Al (in wt %) was selected for scale up and property evaluation.

Comparison of Recovery and Recrystallization in Stainless Steel Following Plane-Wave Shock Loading and Explosive Forming

1970 ◽  
Vol 28 ◽  
pp. 428-429 ◽  
Author(s):  
J. A. Korbonski ◽  
L. E. Murr
Keyword(s):  
Stainless Steel ◽  
Shock Loading ◽  
Pressure Pulse ◽  
Shock Pressure ◽  
304 Stainless Steel ◽  
Strain Rates ◽  
Two Dimensional ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304 ◽  
Explosive Forming

Comparison of recovery rates in materials deformed by a unidimensional and two dimensional strains at strain rates in excess of 104 sec.−1 was performed on AISI 304 Stainless Steel. A number of unidirectionally strained foil samples were deformed by shock waves at graduated pressure levels as described by Murr and Grace. The two dimensionally strained foil samples were obtained from radially expanded cylinders by a constant shock pressure pulse and graduated strain as described by Foitz, et al.

Some aspects of the defect structure in an austenitic stainless steel

1978 ◽  
Vol 36 (1) ◽  
pp. 314-315
Author(s):  
R. Gonzalez ◽  
L. Bru
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Cellular Structures ◽  
Total Strain Amplitude ◽  
Total Deformation ◽  
Density Of Dislocations ◽  
Planar Arrays ◽  
Stacking Fault Tetrahedra ◽  
Distribution Of Dislocations ◽  
Very High

The analysis of stacking fault tetrahedra (SFT) in fatigued metals (1,2) is somewhat complicated, due partly to their relatively low density, but principally to the presence of a very high density of dislocations which hides them. In order to overcome this second difficulty, we have used in this work an austenitic stainless steel that deforms in a planar mode and, as expected, examination of the substructure revealed planar arrays of dislocation dipoles rather than the cellular structures which appear both in single and polycrystals of cyclically deformed copper and silver. This more uniform distribution of dislocations allows a better identification of the SFT.The samples were fatigue deformed at the constant total strain amplitude Δε = 0.025 for 5 cycles at three temperatures: 85, 293 and 773 K. One of the samples was tensile strained with a total deformation of 3.5%.

Pyrolytic carbon filaments and associated catalytic particles formed in steel tubes

1984 ◽  
Vol 42 ◽  
pp. 662-663
Author(s):  
Y. L. Chen ◽  
J. R. Bradley
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Catalyst Particle ◽  
Pyrolytic Carbon ◽  
Plain Carbon Steel ◽  
304 Stainless Steel ◽  
Hydrocarbon Gases ◽  
Steel Tubes ◽  
Filamentous Carbon ◽  
Carbon Filaments

Considerable effort has been directed toward an improved understanding of the production of the strong and stiff ∼ 1-20 μm diameter pyrolytic carbon fibers of the type reported by Koyama and, more recently, by Tibbetts. These macroscopic fibers are produced when pyrolytic carbon filaments (∼ 0.1 μm or less in diameter) are thickened by deposition of carbon during thermal decomposition of hydrocarbon gases. Each such precursor filament normally lengthens in association with an attached catalyst particle. The subject of filamentous carbon formation and much of the work on characterization of the catalyst particles have been reviewed thoroughly by Baker and Harris. However, identification of the catalyst particles remains a problem of continuing interest. The purpose of this work was to characterize the microstructure of the pyrolytic carbon filaments and the catalyst particles formed inside stainless steel and plain carbon steel tubes. For the present study, natural gas (∼; 97 % methane) was passed through type 304 stainless steel and SAE 1020 plain carbon steel tubes at 1240°K.

Preparation of Electron Transparent Metal-Matrix Composites

1968 ◽  
Vol 26 ◽  
pp. 334-335 ◽  
Author(s):  
M. R. Pinnel ◽  
A. Lawley
Keyword(s):  
Stainless Steel ◽  
Load Transfer ◽  
Volume Fraction ◽  
Steel Wire ◽  
Initial Step ◽  
Interfacial Region ◽  
Matrix Composites ◽  
Specific Test ◽  
The Matrix ◽  
The One

Numerous phenomenological descriptions of the mechanical behavior of composite materials have been developed. There is now an urgent need to study and interpret deformation behavior, load transfer, and strain distribution, in terms of micromechanisms at the atomic level. One approach is to characterize dislocation substructure resulting from specific test conditions by the various techniques of transmission electron microscopy. The present paper describes a technique for the preparation of electron transparent composites of aluminum-stainless steel, such that examination of the matrix-fiber (wire), or interfacial region is possible. Dislocation substructures are currently under examination following tensile, compressive, and creep loading. The technique complements and extends the one other study in this area by Hancock.The composite examined was hot-pressed (argon atmosphere) 99.99% aluminum reinforced with 15% volume fraction stainless steel wire (0.006″ dia.).Foils were prepared so that the stainless steel wires run longitudinally in the plane of the specimen i.e. the electron beam is perpendicular to the axes of the wires. The initial step involves cutting slices ∼0.040″ in thickness on a diamond slitting wheel.

Identification by Electron Microdiffraction of Intermetallic Phases in a Duplex Stainless Steel

1990 ◽  
Vol 48 (2) ◽  
pp. 494-495
Author(s):  
A. Redjaïmia ◽  
J.P. Morniroli ◽  
G. Metauer ◽  
M. Gantois
Keyword(s):  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Convergent Beam Electron Diffraction ◽  
Intermetallic Phases ◽  
Small Particles ◽  
Parallel Beam ◽  
Diffraction Patterns ◽  
Average Size ◽  
Convergent Beam ◽  
Electron Microdiffraction

2D and especially 3D symmetry information required to determine the crystal structure of four intermetallic phases present as small particles (average size in the range 100-500nm) in a Fe.22Cr.5Ni.3Mo.0.03C duplex stainless steel is not present in most Convergent Beam Electron Diffraction (CBED) patterns. Nevertheless it is possible to deduce many crystal features and to identify unambiguously these four phases by means of microdiffraction patterns obtained with a nearly parallel beam focused on a very small area (50-100nm).From examinations of the whole pattern reduced (RS) and full (FS) symmetries the 7 crystal systems and the 11 Laue classes are distinguished without ambiguity (1). By considering the shifts and the periodicity differences between the ZOLZ and FOLZ reflection nets on specific Zone Axis Patterns (ZAP) which depend on the crystal system, the centering type of the cell and the glide planes are simultaneously identified (2). This identification is easily done by comparisons with the corresponding simulated diffraction patterns.

Sign in / Sign up

Export Citation Format

Share Document