Studies on the structural, thermal, and dielectric properties of fabricated Nylon 6,9/CaCu3Ti4O12 nanocomposites

2017 ◽  
Vol 24 (2) ◽  
pp. 185-194 ◽  
Author(s):  
Ramaswami Sachidanandan Ernest Ravindran ◽  
Paramanandam Thomas ◽  
Sahadevan Renganathan
Keyword(s):  
Electron Microscopy ◽  
Dielectric Properties ◽  
Dielectric Permittivity ◽  
Scanning Calorimetry ◽  
Melt Mixing ◽  
Two Phase ◽  
Oxalate Precursor ◽  
Transmission Electron ◽  
The Matrix ◽  
High Dielectric

AbstractNylon 6,9/CaCu3Ti4O12 (CCTO) nanocrystal composites with relatively high dielectric permittivity (220 at 100 Hz) were fabricated by melt mixing followed by hot pressing. The CCTO nanoceramics were synthesized using the oxalate precursor route, and the transmission electron microscopy studies exhibited that the crystallites are in the range of 20–200 nm. The nanocomposites were characterized using X-ray diffraction, scanning electron microscopy, thermogravimetric analysis, differential scanning calorimetry, and impedance analyzer to study their structural, thermal, and dielectric properties. The introduction of CCTO nanoparticles into the matrix had influenced the thermal properties. The effective dielectric permittivity of the nanocomposite increased by the augmentation of CCTO content in the Nylon 6,9. Our experimental outcomes showed that the fixed dielectric permittivity of such two-phase composite was established above 200 when the CCTO concentration was closer to its percolation threshold. The room temperature dielectric permittivity as high as 220 at 100 Hz has been achieved when the CCTO content increased to 58 vol% in the polymer and this was increased to 3845 at 150°C. The increase in AC conductivity with the increase in the CCTO content in the polymer matrix supported the hopping of the charge carrier conduction mechanism.

Microstructure and Magnetic Properties of Two Phase β+γ Ferromagnetic Co-Ni-Al Alloys

2009 ◽  
Vol 154 ◽  
pp. 145-150 ◽  
Author(s):  
Wojciech Maziarz ◽  
Jan Dutkiewicz ◽  
Rafał Wróblewski ◽  
Marcin Leonowicz
Keyword(s):  
Electron Microscopy ◽  
Magnetic Properties ◽  
Magnetic Phase ◽  
Scanning Calorimetry ◽  
Two Phase ◽  
Ferromagnetic Alloys ◽  
Transmission Electron ◽  
Heat Treated ◽  
Phase Transition Temperatures ◽  
Microstructure And Magnetic Properties

The microstructure, texture and magnetic properties of two ferromagnetic alloys of composition Co35Ni37Al28 and Co37Ni35Al28 (in at. %) were investigated with optical microscopy (OM), analytical transmission electron microscopy (TEM), scanning electron microscopy (SEM) techniques as well as a vibrating sample magnetometer (VSM). The alloys were plastically deformed and heat treated in order to promote the martensitic transformation. Differential scanning calorimetry (DSC) revealed a drop of Ms temperature due to the increase of Co content in the alloys. The elongated twinned grains of size about 200 m and small precipitates of  phase were identified with the OM techniques. The TEM observations showed the twinned L10 non modulated martensite within the elongated grains and a small amount of ordered ’ phase after the heat treatment. The chemical composition of different martensite grains was established using point analyses of a HAADF-EDS technique. The magnetic phase transition temperatures were determined on the deformed samples using VSM method.

EFFECT OF CALCIUM SULPHATE NANOPARTICLES ON FUSION, MECHANICAL AND THERMAL BEHAVIOUR POLYVINYL CHLORIDE (PVC)

2010 ◽  
Vol 24 (01n02) ◽  
pp. 64-75 ◽  
Author(s):  
C. B. PATIL ◽  
P. S. SHISODE ◽  
U. R. KAPADI ◽  
D. G. HUNDIWALE ◽  
P. P. MAHULIKAR
Keyword(s):  
Electron Microscopy ◽  
Testing Machine ◽  
Calcium Sulphate ◽  
Filler Loading ◽  
Mechanical And Thermal Properties ◽  
Melt Mixing ◽  
Transmission Electron ◽  
In Situ Deposition ◽  
The Matrix ◽  
Internal Mixer

Calcium Sulphate [ CaSO 4] was synthesized by in-situ deposition technique and its nano size (60 to 100 nm) was confirmed by Transmission Electron Microscopy (TEM). Composites of the filler CaSO 4 (micro and nano) and the matrix poly (vinyl chloride) ( PVC ) were prepared with different filler loading (0-5 wt. %) by melt mixing. The Brabender torque rheometer equipped with an internal mixer was used for preparation and evaluation of fusion behaviour of composites of different formulations. The effect of nano and micro- CaSO 4 content on the structure and properties of composites was studied. The nanostructures and dispersion were studied by wide angle X-ray diffraction (WAXD) and scanning electron microscopy (SEM). The mechanical and thermal properties of PVC / micro and nano- CaSO 4 composites were characterized using Universal Testing Machine (UTM) and Thermo Gravimetric Analyzer (TGA). From the results of WAXD and SEM the flocculation of CaSO 4 nanoparticles were observed on the surfaces of PVC matrix. The thermal analysis results showed that the first thermal degradation onset (T onset) of PVC /nano- CaSO 4 composites for 1 wt. % of filler were higher as compared with corresponding microcomposites and pristine PVC . However, the tensile strength was decreasing with increasing filler content while, it shows increment in magnitude at 1 and 2 wt. % of nano- CaSO 4 as compared with corresponding micro- CaSO 4 as well as pristine PVC .

Melting And Solidification Behaviour Of Lead Particles Embedded In Quasicrystalline Matrices

1998 ◽  
Vol 553 ◽  
Author(s):  
Alok Singh ◽  
A. P. Tsai
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Matrix Interface ◽  
Orientation Relationships ◽  
Scanning Calorimetry ◽  
Decagonal Phase ◽  
Solidification Behaviour ◽  
Transmission Electron ◽  
The Matrix ◽  
Melting And Solidification

AbstractComposites of nanoparticles of lead were prepared by embedding into Al-Cu-V and Al- Cu-Fe icosahedral, and Al-Cu-Co decagonal phase alloys by means of rapid solidification. The microstructure of these composites, the orientation relationships and the interfaces formed between the particles and the matrix has been studied by transmission electron microscopy. The melting and solidification behaviour of the lead particles in these matrices has been studied by differential scanning calorimetry. The microstructure and the nature of the particle-matrix interface has been related to the melting/solidification behaviour of the particles in the matrix.

Dispersion and improvement of organoclays in nanocomposites based on poly(propylene oxide)

2020 ◽  
pp. 089270572093917 ◽  
Author(s):  
Lahouari Mrah ◽  
Rachid Meghabar
Keyword(s):  
Electron Microscopy ◽  
Propylene Oxide ◽  
Clay Nanocomposites ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Transmission Electron ◽  
The Matrix ◽  
Organic Clay ◽  
Poly Propylene

This work is mainly concentrated on the preparation and characterization of poly(propylene oxide) (PPO)/organic clay nanocomposites. The effects of the nature of organoclays and the method of preparation have been elucidated to evaluate their morphological, structural and thermal properties. These nanocomposites were characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, thermal analysis (differential scanning calorimetry) and thermogravimetric analysis (TGA). This study involved the use of an Algerian clay called ‘maghnite’ which was modified by an incorporation method using different concentrations of the surfactant cetyltrimethylammonium bromide (CTAB). Propylene oxide (PO) was polymerized in the presence of ethylene glycol and various proportions of organic clay ranging from 1%, 5% and 10% by weight. The structural study by XRD showed, at different loading rates of maghnite and PO in the preparation of PPO/maghnite nanocomposites, different morphologies: intercalated/exfoliated blend and intercalated/agglomerated. TGA showed that the intercalation of PPO at the montmorillonite (MMT)-CTA interface would be more advantageous since the required amount of 5% organic clay (by weight) ensures high thermal stability of the nanocomposites, and the glass transition temperature ( T g) of PPO/MMT nanocomposites is higher than that of PPO since this increase is due to the introduction of clay into the matrix which makes the nanocomposite more rigid.

scholarly journals Study on the Relationships between Microscopic Cross-Linked Network Structure and Properties of Cyanate Ester Self-Reinforced Composites

Polymers ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 950
Author(s):  
Hongtao Cao ◽  
Beijun Liu ◽  
Yiwen Ye ◽  
Yunfang Liu ◽  
Peng Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
The Self ◽  
Reinforced Composites ◽  
Two Phase ◽  
Reinforced Composite ◽  
Transmission Electron ◽  
The Matrix ◽  
Ft Ir ◽  
The Cross

Bisphenol A dicyanate (BADCy) resin microparticles were prepared by precipitation polymerization synthesis and were homogeneously dispersed in a BADCy prepolymer matrix to prepare a BADCy self-reinforced composites. The active functional groups of the BADCy resin microparticles were characterized by Fourier transform infrared (FT-IR) spectroscopy. The results of an FT-IR curve showed that the BADCy resin microparticles had a triazine ring functional group and also had an active reactive group -OCN, which can initiate a reaction with the matrix. The structure of the BADCy resin microparticles was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). From the TEM results, the BADCy resin microparticles dispersed in the solvent were nano-sized and distributed at 40–60 nm. However, from the SEM results, agglomeration occurred after drying, the BADCy resin particels were micron-sized and distributed between 0.3 μm and 0.6 μm. The BADCy resin prepolymer was synthesized in our laboratory. A BADCy self-reinforced composite was prepared by using BADCy resin microparticles as a reinforcement phase. This corresponds to a composite in which the matrix and reinforcement phase are made from different morphologies of the same monomer. The DSC curve showed that the heat flow of the microparticles is different from the matrix during the curing reaction, this means the cured materials should be a microscopic two-phase structure. The added BADCy resin microparticles as reaction sites induced the formation of a more complete and regular cured polymer structure, optimizing the cross-linked network as well as increasing the interplay between the BADCy resin microparticles and prepolymer matrix. Relative to the neat BADCy resin material, the tensile strength, flexural strength, compressive strength and impact strength increased by 98.1%, 40.2%, 27.4%, and 85.4%, respectively. A particle toughening mechanism can be used to explain the improvement of toughness. The reduction in the dielectric constant showed that the cross-linked network of the self-reinforced composite was more symmetrical and less polar than the neat resin material, which supports the enhanced mechanical properties of the self-reinforced composite. In addition, the thermal behavior of the self-reinforced composite was characterized by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The results of DMTA also establishes a basis for enhancing mechanical properties of the self-reinforced composite.

scholarly journals Study on the Photodegradation Stability of Poly(butylene Succinate-co-butylene Adipate)/TiO2 Nanocomposites

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Lihai Cai ◽  
Zhiguo Qi ◽  
Jun Xu ◽  
Baohua Guo ◽  
Zhongyao Huang
Keyword(s):  
Electron Microscopy ◽  
Uv Light ◽  
Chain Scission ◽  
High Energy ◽  
Mechanical Tests ◽  
Scanning Calorimetry ◽  
Butylene Succinate ◽  
Transmission Electron ◽  
The Matrix ◽  
Ft Ir

A poly(butylene succinate-co-butylene adipate)/TiO2 (PBSA/TiO2) nanocomposite was prepared by a melt-blending process. The effect of TiO2 nanoparticles on the photodegradation behaviors of the nanocomposite was investigated by transmission electron microscopy (TEM), differential scanning calorimetry (DSC), Fourier-transform infrared spectroscopy (FT-IR), field-emission scanning electron microscopy (FE-SEM), rheological measurements, and mechanical tests. TEM images of the PBSA/TiO2 revealed that the TiO2 nanoparticles were well dispersed in the matrix without obvious aggregation. The FT-IR results indicated that the TiO2 nanoparticles can block high-energy ultraviolet (UV) light and reduce the degradation of the PBSA matrix. The viscosity analysis results indicated that the TiO2 nanoparticles inhibited the chain scission of PBSA matrix under irradiation. In addition, the surface of the PBSA/TiO2 films and their mechanical properties change less than that of untreated PBSA films during the photoaging process. The obtained results imply that the TiO2 nanoparticles can be considered as an efficient photodegradation-resistant additive to PBSA for reducing photodegradation.

Using crystallographic symmetry in diffraction and contrast analysis

1989 ◽  
Vol 47 ◽  
pp. 504-505
Author(s):  
U. Dahmen ◽  
K.H. Westmacott
Keyword(s):  
Electron Microscopy ◽  
High Symmetry ◽  
Two Phase ◽  
Tem Analysis ◽  
Crystallographic Symmetry ◽  
The Matrix ◽  
Contrast Analysis ◽  
Practical Tool ◽  
Convergent Beam ◽  
Beam Diffraction

Despite the increased use of convergent beam diffraction, symmetry concepts in their more general form are not commonly applied as a practical tool in electron microscopy. Crystal symmetry provides an abundance of information that can be used to facilitate and improve the TEM analysis of crystalline solids. This paper draws attention to some aspects of symmetry that can be put to practical use in the analysis of structures and morphologies of two-phase materials.It has been shown that the symmetry of the matrix that relates different variants of a precipitate can be used to determine the axis of needle- or lath-shaped precipitates or the habit plane of plate-shaped precipitates. By tilting to a special high symmetry orientation of the matrix and by measuring angles between symmetry-related variants of the precipitate it is possible to find their habit from a single micrograph.

scholarly journals Revisiting the Bøggild Intergrowth in Iridescent Labradorite Feldspars: Ordering, Kinetics, and Phase Equilibria

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 727
Author(s):  
Shiyun Jin ◽  
Huifang Xu ◽  
Seungyeol Lee
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Atom Probe ◽  
Phase Region ◽  
Two Phase ◽  
Subsolidus Phase ◽  
Plagioclase Feldspar ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Transmission

The enigmatic Bøggild intergrowth in iridescent labradorite crystals was revisited in light of recent work on the incommensurately modulated structures in the intermediated plagioclase. Five igneous samples and one metamorphic labradorite sample with various compositions and lamellar thicknesses were studied in this paper. The lamellar textures were characterized with conventional transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM). The compositions of individual lamellae were analyzed with high-resolution energy-dispersive X-ray spectroscopy (EDS) mapping and atom probe tomography (APT). The average structure states of the studied samples were also compared with single-crystal X-ray diffraction data (SC-XRD). The Na-rich lamellae have a composition of An44–48, and the Ca-rich lamellae range from An56 to An63. Significant differences between the lamellar compositions of different samples were observed. The compositions of the Bøggild intergrowth do not only depend on the bulk compositions, but also on the thermal history of the host rock. The implications on the subsolidus phase relationships of the plagioclase feldspar solid solution are discussed. The results cannot be explained by a regular symmetrical solvus such as the Bøggild gap, but they support an inclined two-phase region that closes at low temperature.

scholarly journals Study on Structure, Thermal Behavior, and Viscoelastic Properties of Nanodiamond-Reinforced Poly (vinyl alcohol) Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1426
Author(s):  
Tomáš Remiš ◽  
Petr Bělský ◽  
Tomáš Kovářík ◽  
Jaroslav Kadlec ◽  
Mina Ghafouri Azar ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Analysis ◽  
Single Step ◽  
Poly Vinyl Alcohol ◽  
Scanning Calorimetry ◽  
X Ray Scattering ◽  
Transmission Electron ◽  
Primary Particles ◽  
Solution Casting Method ◽  
Average Size

In this work, advanced polymer nanocomposites comprising of polyvinyl alcohol (PVA) and nanodiamonds (NDs) were developed using a single-step solution-casting method. The properties of the prepared PVA/NDs nanocomposites were investigated using Raman spectroscopy, small- and wide-angle X-ray scattering (SAXS/WAXS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). It was revealed that the tensile strength improved dramatically with increasing ND content in the PVA matrix, suggesting a strong interaction between the NDs and the PVA. SEM, TEM, and SAXS showed that NDs were present in the form of agglomerates with an average size of ~60 nm with primary particles of diameter ~5 nm. These results showed that NDs could act as a good nanofiller for PVA in terms of improving its stability and mechanical properties.

scholarly journals Oxygen Induced Phase Transformation in TC21 Alloy with a Lamellar Microstructure

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 163
Author(s):  
Shu Wang ◽  
Yilong Liang ◽  
Hao Sun ◽  
Xin Feng ◽  
Chaowen Huang
Keyword(s):  
Electron Microscopy ◽  
Phase Transformation ◽  
Oxygen Uptake ◽  
Titanium Alloys ◽  
Electron Backscatter Diffraction ◽  
Lamellar Microstructure ◽  
Α Phase ◽  
Transmission Electron ◽  
The Matrix ◽  
Oxygen Ingress

The main objective of the present study was to understand the oxygen ingress in titanium alloys at high temperatures. Investigations reveal that the oxygen diffusion layer (ODL) caused by oxygen ingress significantly affects the mechanical properties of titanium alloys. In the present study, the high-temperature oxygen ingress behavior of TC21 alloy with a lamellar microstructure was investigated. Microstructural characterizations were analyzed through optical microscopy (OM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). Obtained results demonstrate that oxygen-induced phase transformation not only enhances the precipitation of secondary α-phase (αs) and forms more primary α phase (αp), but also promotes the recrystallization of the ODL. It was found that as the temperature of oxygen uptake increases, the thickness of the ODL initially increases and then decreases. The maximum depth of the ODL was obtained for the oxygen uptake temperature of 960 °C. In addition, a gradient microstructure (αp + β + βtrans)/(αp + βtrans)/(αp + β) was observed in the experiment. Meanwhile, it was also found that the hardness and dislocation density in the ODL is higher than that that of the matrix.

Sign in / Sign up

Export Citation Format

Share Document