scholarly journals Current mode pulse width modulation/pulse position modulation based on phase lock loop

2017 ◽  
Vol 68 (3) ◽  
pp. 180-187
Author(s):  
Pichet Wisartpong ◽  
Vorapong Silaphan ◽  
Sunee Kurutach ◽  
Paramote Wardkein
Keyword(s):  
Pulse Width ◽  
Pulse Width Modulation ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Technology ◽  
Phase Lock Loop ◽  
Center Frequency ◽  
Loop Filter ◽  
Chip Area ◽  
Fully Integrated

Abstract In this paper, the fully integrated CMOS current mode PLL with current input injects at the place of input or output of the loop filter without summing amplifier circuit. It functions as PPM and PWM circuit is present. In addition, its frequency response is an analysis which electronic tuning BPF and LPF are obtained. The proposed circuit has been designed with 0.18 μm CMOS technology. The simulation results of this circuit can be operated at 2.5 V supply voltage, at center frequency 100 MHz. The linear range of input current can be adjusted from 43 μA to 109 μA, and the corresponding duty cycle of pulse width output is from 93% to 16% and the normalized pulse position is from 0.93 to 0.16. The power dissipation of this circuit is 4.68 mW with the total chip area is 28 μm × 60 μm.

COMPLEMENTARY AND DOUBLE-EDGE BASED: A 5-BIT CMOS DIGITAL PULSE-WIDTH MODULATION (PWM) DESIGN WITH MULTIPLE OUTPUTS FOR LED DIMMING APPLICATION

2014 ◽  
Vol 23 (02) ◽  
pp. 1450030 ◽  
Author(s):  
YU-CHERNG HUNG
Keyword(s):  
Pulse Width ◽  
High Speed ◽  
Pulse Width Modulation ◽  
Supply Voltage ◽  
Light Emitting Diode ◽  
Cmos Technology ◽  
Chip Area ◽  
Double Edge ◽  
Digital Pulse ◽  
Dimming Control

In this paper, a compact high-precision digital pulse-width modulation (DPWM) CMOS circuit is proposed. The circuit, with multiple output capability, allows brightness control of red, green, and blue (RGB) light emitting diode (LED) lighting. The PWM technique is used for LED dimming control to avoid the problem of color shifting. In this design, complementary concepts and hardware sharing are utilized to achieve a compact architecture and small chip area. A double-edge triggered technique is adopted to enhance the capability of high-speed operation. An experimental chip has been realized by using TSMC 0.18-μm CMOS technology. Simulation results show that the proposed 5-bit PWM circuit can operate at 200 MHz, 32 duty cycles adjustable, and within only 1-ns time error. The chip's measured results show that the new PWM circuit with three output channels works successfully at a supply voltage of 1.8-V, clock of 50-MHz, and resolution of 32 adjustable per channel. The core area of the chip is only 280 × 52.5 μm2.

scholarly journals Design of area-efficient GHz range current mode frequency synthesizer using standard CMOS technology

2019 ◽  
Vol 70 (4) ◽  
pp. 323-328
Author(s):  
Dan-Dan Zheng ◽  
Yu-Bin Li ◽  
Chang-Qi Wang ◽  
Kai Huang ◽  
Xiao-Peng Yu
Keyword(s):  
Frequency Synthesizer ◽  
Frequency Tuning ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Technology ◽  
Mode Frequency ◽  
Loop Filter ◽  
Silicon Area ◽  
Power Efficient ◽  
A Current

Abstract In this paper, an area and power efficient current mode frequency synthesizer for system-on-chip (SoC) is proposed. A current-mode transformer loop filter suitable for low supply voltage is implemented to remove the need of a large capacitor in the loop filter, and a current controlled oscillator with additional voltage based frequency tuning mechanism is designed with an active inductor. The proposed design is further integrated with a fully programmable frequency divider to maintain a good balance among output frequency operating range, power consumption as well as silicon area. A test chip is implemented in a standard 0.13 µm CMOS technology, measurement result demonstrates that the proposed design has a working range from 916 MHz to 1.1 l GHz and occupies a silicon area of 0.25 mm2 while consuming 8.4 mW from a 1.2 V supply.

scholarly journals A Low-Voltage, Low-Power Reconfigurable Current-Mode Softmax Circuit for Analog Neural Networks

Electronics ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 1004
Author(s):  
Massimo Vatalaro ◽  
Marco Lanuzza ◽  
Felice Crupi ◽  
Tatiana Moposita ◽  
Lionel Trojman ◽  
...  
Keyword(s):  
Low Power ◽  
Modular Design ◽  
Low Voltage ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Technology ◽  
Chip Area ◽  
Analog Implementation ◽  
Efficient Option ◽  
P Type

This paper presents a novel low-power low-voltage analog implementation of the softmax function, with electrically adjustable amplitude and slope parameters. We propose a modular design, which can be scaled by the number of inputs (and of corresponding outputs). It is composed of input current–voltage linear converter stages (1st stages), MOSFETs operating in a subthreshold regime implementing the exponential functions (2nd stages), and analog divider stages (3rd stages). Each stage is only composed of p-type MOSFET transistors. Designed in a 0.18 µm CMOS technology (TSMC), the proposed softmax circuit can be operated at a supply voltage of 500 mV. A ten-input/ten-output realization occupies a chip area of 2570 µm2 and consumes only 3 µW of power, representing a very compact and energy-efficient option compared to the corresponding digital implementations.

scholarly journals An 18.8–33.9 GHz, 2.26 mW Current-Reuse Injection-Locked Frequency Divider for Radar Sensor Applications

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2551
Author(s):  
Kwang-Il Oh ◽  
Goo-Han Ko ◽  
Jeong-Geun Kim ◽  
Donghyun Baek
Keyword(s):  
Supply Voltage ◽  
Cmos Technology ◽  
Frequency Divider ◽  
Oxide Semiconductor ◽  
Center Frequency ◽  
Radar Sensor ◽  
Frequency Locking ◽  
Current Reuse ◽  
Sensor Applications ◽  
Locking Range

An 18.8–33.9 GHz, 2.26 mW current-reuse (CR) injection-locked frequency divider (ILFD) for radar sensor applications is presented in this paper. A fourth-order resonator is designed using a transformer with a distributed inductor for wideband operating of the ILFD. The CR core is employed to reduce the power consumption compared to conventional cross-coupled pair ILFDs. The targeted input center frequency is 24 GHz for radar application. The self-oscillated frequency of the proposed CR-ILFD is 14.08 GHz. The input frequency locking range is from 18.8 to 33.8 GHz (57%) at an injection power of 0 dBm without a capacitor bank or varactors. The proposed CR-ILFD consumes 2.26 mW of power from a 1 V supply voltage. The entire die size is 0.75 mm × 0.45 mm. This CR-ILFD is implemented in a 65 nm complementary metal-oxide semiconductor (CMOS) technology.

scholarly journals Investigation of PVT-Aware STT-MRAM Sensing Circuits for Low-VDD Scenario

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 551
Author(s):  
Zhongjian Bian ◽  
Xiaofeng Hong ◽  
Yanan Guo ◽  
Lirida Naviner ◽  
Wei Ge ◽  
...  
Keyword(s):  
Nonvolatile Memory ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor

Spintronic based embedded magnetic random access memory (eMRAM) is becoming a foundry validated solution for the next-generation nonvolatile memory applications. The hybrid complementary metal-oxide-semiconductor (CMOS)/magnetic tunnel junction (MTJ) integration has been selected as a proper candidate for energy harvesting, area-constraint and energy-efficiency Internet of Things (IoT) systems-on-chips. Multi-VDD (low supply voltage) techniques were adopted to minimize energy dissipation in MRAM, at the cost of reduced writing/sensing speed and margin. Meanwhile, yield can be severely affected due to variations in process parameters. In this work, we conduct a thorough analysis of MRAM sensing margin and yield. We propose a current-mode sensing amplifier (CSA) named 1D high-sensing 1D margin, high 1D speed and 1D stability (HMSS-SA) with reconfigured reference path and pre-charge transistor. Process-voltage-temperature (PVT) aware analysis is performed based on an MTJ compact model and an industrial 28 nm CMOS technology, explicitly considering low-voltage (0.7 V), low tunneling magnetoresistance (TMR) (50%) and high temperature (85 °C) scenario as the worst sensing case. A case study takes a brief look at sensing circuits, which is applied to in-memory bit-wise computing. Simulation results indicate that the proposed high-sensing margin, high speed and stability sensing-sensing amplifier (HMSS-SA) achieves remarkable performance up to 2.5 GHz sensing frequency. At 0.65 V supply voltage, it can achieve 1 GHz operation frequency with only 0.3% failure rate.

scholarly journals Receiver Designs for Electronic Toll Collection Systems : A Survey

2020 ◽  
pp. 576-581
Author(s):  
Rarika Ravi ◽  
Anu Assis
Keyword(s):  
Dynamic Range ◽  
Supply Voltage ◽  
Automatic Gain Control ◽  
Power Level ◽  
Cmos Technology ◽  
Electronic Toll Collection ◽  
Chip Area ◽  
Advantages And Disadvantages ◽  
Digitally Controlled ◽  
Toll Collection

<p>This paper discusses about different receiver designs adopted so far for various electronic toll collection systems. A comparative analysis based on the discussions is also provided. It shows that each design has it's own advantages and disadvantages compared to others. The main aim of this paper is to identify the most suitable design. The researches shows that the receiver design described in the 5.8GHz digitally controlled DSRC receiver for Chinese electronic toll collection system is the most suitable one. Here all RF, IF blocks and digital baseband for on-chip automatic gain control, are integrated on an RF-SoC. The proposed digitally controlled LNA and mixer circuits are elaborated. The technology used is 0.13μm CMOS technology. The RF block occupies a chip area of 0.75mm2. It consumes 22mA under a 1.5V supply voltage. The bit error rate maintains better than 10-6, the input power level varies from -75dBm to -8dBm. This design provides a receiver sensitivity improvement of at least 25%, and a dynamic range enhancement of at least 12%.</p>

A CMOS Automatic Gain Control Circuit for Biomedical Applications

2015 ◽  
Vol 645-646 ◽  
pp. 1308-1313
Author(s):  
Zhi Qiang Gao ◽  
Fu Xiang Huang ◽  
Jing Li ◽  
Liang Yin ◽  
Xiao Wei Liu
Keyword(s):  
Exponential Function ◽  
Biomedical Applications ◽  
Low Voltage ◽  
Supply Voltage ◽  
Automatic Gain Control ◽  
Gain Control ◽  
Cmos Technology ◽  
Chip Area ◽  
Gain Variation ◽  
Linearity Error

In this paper, a low-voltage automatic gain control (AGC) circuits is presented. The proposed circuit uses a novel approximated exponential function to increase the dB-linear output range. The three-stage AGC is fabricated in 0.18μm CMOS technology and shows the maximum gain variation of more than 100dB and a 67dB linear range with linearity error of less than ±1dB. The range of gain variation can be controlled from 34 to 101dB. The AGC dissipates less than 2.3mA under 1.8V supply voltage while occupying 0.4mm2 of chip area.

scholarly journals DIGITAL CONTROLLED OSCILLATOR (DCO) FOR ALL DIGITAL PHASE-LOCKED LOOP (ADPLL) – A REVIEW

2019 ◽  
Vol 82 (1) ◽  
Author(s):  
Florence Choong ◽  
Mamun Ibne Reaz ◽  
Mohamad Ibrahim Kamaruzzaman ◽  
Md. Torikul Islam Badal ◽  
Araf Farayez ◽  
...  
Keyword(s):  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Phase Locked Loop ◽  
Cmos Technology ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Process Technology ◽  
Chip Area ◽  
Digital Phase ◽  
Low Power Dissipation

Digital controlled oscillator (DCO) is becoming an attractive replacement over the voltage control oscillator (VCO) with the advances of digital intensive research on all-digital phase locked-loop (ADPLL) in complementary metal-oxide semiconductor (CMOS) process technology. This paper presents a review of various CMOS DCO schemes implemented in ADPLL and relationship between the DCO parameters with ADPLL performance. The DCO architecture evaluated through its power consumption, speed, chip area, frequency range, supply voltage, portability and resolution. It can be concluded that even though there are various schemes of DCO that have been implemented for ADPLL, the selection of the DCO is frequently based on the ADPLL applications and the complexity of the scheme. The demand for the low power dissipation and high resolution DCO in CMOS technology shall remain a challenging and active area of research for years to come. Thus, this review shall work as a guideline for the researchers who wish to work on all digital PLL.

scholarly journals Floating Active Inductor Based Trans-Impedance Amplifier in 0.18 μm CMOS Technology for Optical Applications

Electronics ◽  
2019 ◽  
Vol 8 (12) ◽  
pp. 1547
Author(s):  
Xiangyu Chen ◽  
Yasuhiro Takahashi
Keyword(s):  
Power Dissipation ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Chip Area ◽  
Active Inductors ◽  
Low Pass ◽  
Optical Applications ◽  
Fifth Order

In this paper, a transimpedance amplifier (TIA) based on floating active inductors (FAI) is presented. Compared with conventional TIAs, the proposed TIA has the advantages of a wider bandwidth, lower power dissipation, and smaller chip area. The schematics and characteristics of the FAI circuit are explained. Moreover, the proposed TIA employs the combination of capacitive degeneration, the broadband matching network, and the regulated cascode input stage to enhance the bandwidth and gain. This turns the TIA design into a fifth-order low pass filter with Butterworth response. The TIA is implemented using 0.18 μ m Rohm CMOS technology and consumes only 10.7 mW with a supply voltage of 1.8 V. When used with a 150 fF photodiode capacitance, it exhibits the following characteristics: gain of 41 dB Ω and −3 dB frequency of 10 GHz. This TIA occupies an area of 180 μ m × 118 μ m.

A LOW POWER CRYOGENIC CMOS ROIC DESIGN FOR 512 × 512 IRFPA

2013 ◽  
Vol 22 (10) ◽  
pp. 1340033 ◽  
Author(s):  
HONGLIANG ZHAO ◽  
YIQIANG ZHAO ◽  
YIWEI SONG ◽  
JUN LIAO ◽  
JUNFENG GENG
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Integrated Circuit ◽  
High Performance ◽  
Supply Voltage ◽  
Cmos Technology ◽  
High Gain ◽  
Readout Integrated Circuit ◽  
Chip Area ◽  
Operating Modes

A low power readout integrated circuit (ROIC) for 512 × 512 cooled infrared focal plane array (IRFPA) is presented. A capacitive trans-impedance amplifier (CTIA) with high gain cascode amplifier and inherent correlated double sampling (CDS) configuration is employed to achieve a high performance readout interface for the IRFPA with a pixel size of 30 × 30 μm2. By optimizing column readout timing and using two operating modes in column amplifiers, the power consumption is significantly reduced. The readout chip is implemented in a standard 0.35 μm 2P4M CMOS technology. The measurement results show the proposed ROIC achieves a readout rate of 10 MHz with 70 mW power consumption under 3.3 V supply voltage from 77 K to 150 K operating temperature. And it occupies a chip area of 18.4 × 17.5 mm2.

Sign in / Sign up

Export Citation Format

Share Document