scholarly journals Viscoelastic properties of green wood across the grain measured by harmonic tests in the range 0–95°C: Hardwood vs. softwood and normal wood vs. reaction wood

Holzforschung ◽  
2007 ◽  
Vol 61 (5) ◽  
pp. 548-557 ◽  
Author(s):  
Vincent Placet ◽  
Joëlle Passard ◽  
Patrick Perré
Keyword(s):  
Storage Modulus ◽  
Viscoelastic Properties ◽  
Tension Wood ◽  
Radial Direction ◽  
Lignin Content ◽  
Softening Temperature ◽  
Normal Wood ◽  
Reaction Wood ◽  
Opposite Wood ◽  
Wood Compression

Abstract The viscoelastic properties of wood have been investigated with a dynamic mechanical analyser specifically developed for wooden materials, the WAVET device. Measurements were carried out on four wood species in the temperature range 0–100°C at frequencies varying between 5 mHz and 10 Hz. Wood samples were tested under water-saturated conditions in the radial and tangential directions. As expected, the radial direction always revealed a higher storage modulus than the tangential direction. Great differences were also observed in the loss factor. The tanδ peak and internal friction were higher in the tangential than in the radial direction. This behaviour is attributed to the fact that anatomical elements act as a function of the direction. The viscoelastic behaviour of reaction wood differs from that of normal or opposite wood. Compression wood of spruce, which has a higher lignin content, is denser and stiffer in transverse directions than normal wood, and has a lower softening temperature (T g). In tension wood, the G-layer is weakly attached to the rest of the wall layers. This may explain why the storage modulus and softening temperature of tension wood are lower than those for opposite wood. We also demonstrate that the time-temperature equivalence fits only around the transition region, i.e., between T g and T g+30°C. Apart from these regions, the response of wood reflects the combined effects of all its constitutive polymers, so that the equivalence is no longer valid.

scholarly journals Influência do lenho de tração nas propriedades físicas da madeira de Eucalyptus sp.

2010 ◽  
Vol 1 (1) ◽  
pp. 6-11
Author(s):  
Thiago Campos Monteiro ◽  
Renato da Silva Vieira ◽  
José Tarcísio Lima ◽  
Edy Eime Pereira Baraúna ◽  
Duam Matosinhos de Carvalho ◽  
...  
Keyword(s):  
Tension Wood ◽  
Basic Density ◽  
Eucalyptus Camaldulensis ◽  
Normal Wood ◽  
Reaction Wood ◽  
Opposite Wood ◽  
The Face ◽  
Eucalyptus Maculata ◽  
Shrinkage Coefficient

The reaction wood is formed in an attempt to remain upright tree in response to the action of forces such as winds, irregular crown or slope of the land that tend to incline it. In hardwoods, as in Eucalyptus, this type of wood is called tension wood and occurs in the region of the stem facing the face of force application. Indicative of the presence of this type of wood is the high shrinkage and basic density compared to normal wood. Once the basic density and shrinkage are parameters for determining the quality of the wood, this study aimed to evaluate the variation of basic density and shrinkage of opposite and tension wood along the radius in four species of Eucalyptus sp. Four tree species Eucalyptus camaldulensis, Eucalyptus maculata, Eucalyptus pilularis and Eucalyptus urophylla, with 32 years of age, were taken from an experimental planting of the Federal University of Lavras. Specimens were made to represent the diametrical variation of the opposite of tension wood in disks cut at the dbh. The results indicate that the properties of radial, tangential and volumetric shrinkage, coefficient of anisotropy and basic density did not differ statistically between the tensionand opposite wood.

The nature of reaction wood. IV. Variations in cell wall organization of tension wood fibres

1955 ◽  
Vol 3 (2) ◽  
pp. 177 ◽  
Author(s):  
AB Wardrop ◽  
HE Dadswell
Keyword(s):  
Cell Wall ◽  
Tension Wood ◽  
Secondary Wall ◽  
Degree Of Crystallinity ◽  
Tropical Species ◽  
Normal Wood ◽  
Reaction Wood ◽  
Gelatinous Layer ◽  
Wood Fibres ◽  
Cell Wall Organization

The cell wall organization, the cell wall texture, and the degree of lignification of tension wood fibres have been investigated in a wide variety of temperate and tropical species. Following earlier work describing the cell wall structure of tension wood fibres, two additional types of cell wall organization have been observed. In one of these, the inner thick "gelatinous" layer which is typical of tension wood fibres exists in addition to the normal three-layered structure of the secondary wall; in the other only the outer layer of the secondary wall and the thick gelatinous layer are present. In all the tension wood examined the micellar orientation in the inner gelatinous layer has been shown to be nearly axial and the cellulose of this layer found to be in a highly crystalline state. A general argument is presented as to the meaning of differences in the degree, of crystallinity of cellulose. The high degree of crystallinity of cellulose in tension wood as compared with normal wood is attributed to a greater degree of lateral order in the crystalline regions of tension wood, whereas the paracrystalline phase is similar in both cases. The degree of lignification in tension wood fibres has been shown to be extremely variable. However, where the degree of tension wood development is marked as revealed by the thickness of the gelatinous layer the lack of lignification is also most marked. Severity of tension wood formation and lack of lignification have also been correlated with the incidence of irreversible collapse in tension wood. Such collapse can occur even when no whole fibres are present, e.g. in thin cross sections. Microscopic examination of collapsed samples of tension wood has led to the conclusion that the appearance of collapse in specimens containing tendon wood can often be attributed in part to excessive shrinkage associated with the development of fissures between cells, although true collapse does also occur. Possible explanations of the irreversible shrinkage and collapse of tension wood fibres are advanced.

scholarly journals QUALITY OF REACTION WOOD IN Eucalyptus TREES TILTED BY WIND FOR PULP PRODUCTION

CERNE ◽  
2017 ◽  
Vol 23 (3) ◽  
pp. 291-297
Author(s):  
Walter Torezani Neto Boschetti ◽  
Juarez Benigno Paes ◽  
Graziela Baptista Vidaurre ◽  
Marina Donária Chaves Arantes ◽  
João Gabriel Missia da Silva
Keyword(s):  
Chemical Composition ◽  
Chemical Constituents ◽  
Wood Quality ◽  
Basic Density ◽  
Kraft Pulping ◽  
Normal Wood ◽  
Reaction Wood ◽  
Opposite Wood ◽  
Holocellulose Content

ABSTRACT This study aims to evaluate the quality of normal, tension and opposite wood of eucalyptus trees lengthwise, in straight and inclined stems, affected by wind action. It also aims to explain the pulping parameters resultant from the quality of the wood. The trees were grouped into four tilt ranges, ranging from 0 to 50º, and the basic density, chemical composition of the wood, and performance in kraft pulping were assessed. Normal and tension wood had similar basic densities; while for opposite wood, the density was lower, being responsible for a decrease in reaction wood density. The chemical composition of the wood was influenced by the presence of reaction wood in the stem. Tension and opposite wood showed lower levels of extractives and lignin and higher holocellulose content when compared to normal wood, with favorable wood quality for pulping. The increase in holocellulose content and the reduction of lignin and extractives content contributed positively to a more delignified pulp and reduction of the Kappa number. However, after cooking the reaction wood under the same conditions as those of normal wood, reaction wood pulping tends to have a lower screen yields. Due to differences in basic density and chemical constituents between opposite and normal wood, it is recommended not to designate the opposite wood as normal wood.

ANATOMY AND CHEMICAL COMPOSITION OF LIRIODENDRON TULIPIFERA STEMS INCLINED AT DIFFERENT ANGLES

IAWA Journal ◽  
2014 ◽  
Vol 35 (4) ◽  
pp. 463-475 ◽  
Author(s):  
Tokiko Hiraiwa ◽  
Haruna Aiso ◽  
Futoshi Ishiguri ◽  
Yuya Takashima ◽  
Kazuya Iizuka ◽  
...  
Keyword(s):  
Lignin Content ◽  
Fibre Length ◽  
Liriodendron Tulipifera ◽  
Original Position ◽  
Chemical Characteristics ◽  
Normal Wood ◽  
Reaction Wood ◽  
Glucose Content ◽  
Wood Fibres ◽  
S2 Layer

The anatomical and chemical characteristics of reaction wood (RW) were investigated in Liriodendron tulipifera Linn. Stems of seedlings were artificially inclined at angles of 30 (RW-30), 50 (RW-50) and 70° (RW-70) from the vertical, and compared with normal wood (NW) from a vertical seedling stem. The smallest values for the wood fibre length and vessel number were observed in RW-50. The pit aperture angle was less than 10° in RW-30 and RW-50, in which reduced lignin content was observed in the S2 layer of the wood fibres. An increase in the glucose content and a decrease in the lignin and xylose content was observed in RW-50. The stem inclination angle affected the degree of RW development with regard to anatomical and chemical characteristics: the severest RW was observed in RW-50, followed by RW-30. RW-70 was similar in anatomical and chemical characteristics to NW, apparently because the inclination was too strong to enable recovery of its original position. In this case a vertical sprouting stem was formed to replace the inclined stem.

Strength and stiffness of the reaction wood in five Eucalyptus species

Holzforschung ◽  
2019 ◽  
Vol 73 (2) ◽  
pp. 219-222
Author(s):  
Bruno Charles Dias Soares ◽  
José Tarcísio Lima ◽  
Selma Lopes Goulart ◽  
Claudineia Olímpia de Assis
Keyword(s):  
Mechanical Behavior ◽  
Tension Wood ◽  
Compression Wood ◽  
Vertical Position ◽  
Eucalyptus Species ◽  
Reaction Wood ◽  
Opposite Wood ◽  
Average Slope ◽  
Strength And Stiffness

AbstractTree stems deviating from the vertical position react by the formation of tension wood (TW) or compression wood (CW), which are called in general as reaction wood (RW), in which the cells are modified chemically and anatomically. The focus of the present work is the mechanical behavior of TW in five 37-year-oldEucalyptusspecies, which were grown on a planting area with an average slope of 28% leading to decentralized pith in the trees, which is an unequivocal indication of the presence of RW. TW and opposite wood (OW) samples were isolated and subjected to a compression-parallel-to-grain test. It was observed that TW is less resistant and less stiff than the OW.

Wood Anatomy of nine Japanese Hardwood species forming reaction wood without gelatinous fibers

IAWA Journal ◽  
2010 ◽  
Vol 31 (2) ◽  
pp. 191-202 ◽  
Author(s):  
R.S. Sultana ◽  
F. Ishiguri ◽  
S. Yokota ◽  
K. Iizuka ◽  
T. Hiraiwa ◽  
...  
Keyword(s):  
Lignin Content ◽  
Reaction Wood ◽  
Wood Fibers ◽  
Acetyl Bromide ◽  
Euonymus Alatus ◽  
Opposite Wood ◽  
Gelatinous Fibers ◽  
Hardwood Species ◽  
Daphne Odora ◽  
Clerodendron Trichotomum

The anatomy of reaction wood was studied in nine naturally growing Japanese hardwood species, all showing eccentric growth on the upper side of their leaning branches. The number of vessels decreased in the xylem of the upper side accompanying the formation of reaction wood. A typical G-layer was not detected in the reaction wood fibers, but an S3 layer was present in all nine species. The cellulose microfibril arrangement with an S helix was similar in the S3 layers of both reaction and opposite wood fibers. A decrease of lignin content occurred in the reaction wood fibers in all nine species. The coniferyl and sinapyl aldehyde units in the lignins were strongly reduced in the S2 layer of reaction wood fibers of four species, i.e., Euscaphis japonica, Rhododendron wadanum, Clerodendron trichotomum, and Daphne odora, and much less so in five other species, i.e., Viburnum dilatatum, Enkianthus subsessilis, Euonymus alatus, Ilex macropoda, and Ilex crenata. The syringyl content was lower in the S2 layer of reaction wood fibers than that in opposite wood of all nine species. On the other hand, chemical analysis of lignin using the acetyl bromide method showed that, among the nine species, lignin content was reduced most strongly in Clerodendron trichotomum. Tension wood-like characteristics are present on the upper side of leaning branches in all nine species, except that G-fibers are absent.

scholarly journals Structural differences between reaction wood and opposite wood with different drying temperatures

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 4407-4416
Author(s):  
Ivan Klement ◽  
Tatiana Vilkovská ◽  
Peter Vilkovský ◽  
Štěpán Hýsek
Keyword(s):  
Physical And Mechanical Properties ◽  
Thick Wall ◽  
Normal Wood ◽  
Reaction Wood ◽  
Drying Time ◽  
Fiber Cells ◽  
Opposite Wood ◽  
Negative Effect ◽  
Higher Temperature ◽  
End Times

Reaction wood is characterized by having different anatomical and chemical features than normal wood. The different composition of cell walls, the higher quantitative proportion of thick-wall fiber cells, diameter, and the abundance of vessels have remarkable effects on reaction wood’s physical and mechanical properties. Reaction wood has fewer vascular cells. In addition, it has a smaller lumen diameter, which results in reduced permeability. Therefore, reaction wood is more difficult to dry at a certain moisture content. The differences in the drying times of the reaction wood and the normal wood were largest at a temperature of 60 °C and durations greater than 30 h, and the reaction wood dried more slowly. At a temperature of 120 °C, the differences in drying time were minimalized, and drying end times were almost identical. The expected negative effect of higher temperature on the morphology of reaction wood and opposition wood was not confirmed.

TENSION WOOD-LIKE REACTION WOOD IN VESSEL-LESS TETRACENTRON SINENSE

IAWA Journal ◽  
2016 ◽  
Vol 37 (3) ◽  
pp. 372-382 ◽  
Author(s):  
H. Aiso ◽  
F. Ishiguri ◽  
T. Ohkubo ◽  
S. Yokota
Keyword(s):  
Tension Wood ◽  
Secondary Wall ◽  
Special Function ◽  
Lignin Content ◽  
Microfibril Angle ◽  
Chemical Characteristics ◽  
Reaction Wood ◽  
Lignin Distribution ◽  
Angiosperm Species ◽  
Tetracentron Sinense

The objective of this study is to clarify the anatomical characteristics and lignin distribution of reaction wood in a vessel-less angiosperm species, Tetracentron sinense Oliv. Sample disks (1 cm in thickness) were collected from three different positions of a Tetracentron sinense tree. Cell morphologies, the microfibril angle (MFA) in the S2 layer, lignin distribution, and lignin content were measured. There was neither a gelatinous (G-)layer nor an S3 layer on the upper side of inclined samples. However, the secondary wall of the normal tracheids was only weakly stained by Mäule and phloroglucinol-HCl. MFA in the S2 layer and lignin content decreased on the upper side of inclined samples. This qualifies the reaction wood of Tetracentron as “tension wood-like”. The so-called “unusual tracheids”, typical for the wood of Tetracentron, showed weaker changes in their anatomical and chemical characteristics in reaction wood than normal tracheids, indicating their special function in water transport. It is hypothesized that vessel-less angiosperms rich in syringyl units in their lignin, produce tension wood-like reaction wood on the upper side of inclined stems or branches, with lower MFA and lignin content in their normal tracheid walls, irrespective of whether a typical G-layer is formed or not.

Air permeability in longitudinal and radial directions of compression wood of Picea abies L. and tension wood of Fagus sylvatica L.

Holzforschung ◽  
2009 ◽  
Vol 63 (3) ◽  
Author(s):  
Asghar Tarmian ◽  
Patrick Perré
Keyword(s):  
Picea Abies ◽  
Fagus Sylvatica ◽  
Tension Wood ◽  
Compression Wood ◽  
Air Permeability ◽  
Normal Wood ◽  
Reaction Wood ◽  
Anatomical Point ◽  
Bordered Pits ◽  
The Difference

Abstract The air permeability in longitudinal and radial directions of compression wood in spruce (Picea abies) and tension wood in beech (Fagus sylvatica) was compared with that of the corresponding normal wood. The primary aim of the present study was to explain why the reaction woods dry more slowly than the normal woods in the domain of free water. A number of boards conventionally dried to an average final moisture content of 12% were chosen to perform the measurements. Bordered pits on the radial walls of longitudinal tracheids in the compression and normal wood and intervessel or intervascular pits in the tension and normal wood were also examined. The reaction wood of both species is less permeable than the normal wood, both in longitudinal and radial directions. The difference in permeability was more pronounced between compression and normal wood of spruce, especially in longitudinal direction. From an anatomical point of view, this is likely related to some differences in anatomical characteristics affecting the airflow paths, such as the pit features. Such results can explain the difference in drying kinetics of the reaction and normal woods in the capillary regime of drying.

Studies about the Influence Factors on Ultrasonic Velocity of Domestic Red Pine

2006 ◽  
Vol 321-323 ◽  
pp. 1177-1181 ◽  
Author(s):  
So Ra Han ◽  
Chun Young Park ◽  
Young Geun Eom ◽  
Jun Jae Lee
Keyword(s):  
Ultrasonic Velocity ◽  
Radial Direction ◽  
Influence Factors ◽  
Tangential Direction ◽  
Red Pine ◽  
Normal Wood ◽  
Reaction Wood ◽  
Decayed Wood ◽  
Effect Factors ◽  
Factors Influencing

This research was carried out to grasp the factors influencing to the ultrasonic velocity to improve the efficiency of the ultrasonic wave test using as the method of NDE of wood. However, it was difficult to detect the defect of wood accurately, because ultrasonic velocity is influenced by various factors. So, some effect factors, which were not concerned with decay, were confirmed at first. Therefore, in this research, we tried to find the factors which affect on the natural characters and the ultrasonic velocity at decayed wood, additionally, we tried an anatomic experiment and analyze. As a result of research, the velocity at radial direction was faster than that at tangential direction and the ultrasonic velocity at immature wood and reaction wood was slower than that at normal wood. And the ultrasonic velocity was more the slower at bigger the length of decay and reduction of weight.

Sign in / Sign up

Export Citation Format

Share Document