Wood Fracture Pattern during the Water Adsorption Process

Holzforschung ◽  
2003 ◽  
Vol 57 (6) ◽  
pp. 639-643 ◽  
Author(s):  
W. Liyu ◽  
L. Zhenyou ◽  
Z. Guangjie
Keyword(s):  
Fracture Toughness ◽  
Relative Humidity ◽  
Moisture Content ◽  
Constant Temperature ◽  
Maximum Load ◽  
Fracture Pattern ◽  
Propagation Path ◽  
Betula Platyphylla ◽  
Moisture Adsorption ◽  
Pinus Bungeana

Summary A research program was conducted to investigate the effect of water transition on wood fracture properties, focusing on fracture behavior and patterns with different crack orientations of Betula platyphylla Suk. and Pinus bungeana in three different moisture adsorption processes. At a constant temperature of 20°C, three levels of relative humidity were considered: 66%, 82% and 100%. The results indicated that moisture content did not influence the crack propagation path, while specimen crack orientation did. With longer moisture adsorption times, the time needed to reach the maximum load from the critical load also grew; this is because below the fiber saturation point, from excessive dryness to a certain moisture content, the cell wall becomes less brittle and the toughness is enhanced. At 20°C constant temperature, the fracture toughness gradually increased from oven-dry state adsorbing moisture to 82% relative humidity, but decreased from 82% to 100% relative humidity. Within a tree species, fracture toughness depended on specimen type. The fracture toughness of LT specimens was by far higher than that of TL and TR specimens. The LT specimen fracture toughness of Betula platyphylla Suk. was comparable to that of Pinus bungeana.

Evaluation of parameters influencing the withdrawal strength of oak and beech dowels

BioResources ◽  
2020 ◽  
Vol 15 (1) ◽  
pp. 1665-1677
Author(s):  
Milan Podlena ◽  
Martin Böhm ◽  
Štěpán Hýsek ◽  
Jiří Procházka ◽  
Robert Černý
Keyword(s):  
Relative Humidity ◽  
Moisture Content ◽  
Constant Temperature ◽  
Wood Species ◽  
Quercus Robur ◽  
Oak Wood ◽  
Bonded Joint ◽  
Low Humidity ◽  
Fagus Sylvatica L ◽  
Evaluation Of Parameters

The withdrawal strength of plain dowels with nominal diameter of 8 mm was compared with the spiral dowels manufactured from beech (Fagus sylvatica L.) and oak wood (Quercus robur L.). The test specimens were tested after conditioning at relative humidity (RH) 25%, 45%, 65%, and 85% at a constant temperature of 20 °C. Therefore, the influence of relative humidity (respective moisture content), dowel structure, and wood species of the dowels on the withdrawal strength was determined. The structure and low humidity (RH 25%) caused the highest strength (8.6 MPa) of spiral dowels. Compared to plain dowels, the higher withdrawal strength of spiral dowels was statistically significant. Adversely, the lowest withdrawal strength was found for plain beech dowels (3 MPa), which, in addition to higher relative humidity (RH 85%), was also caused by a combination of plain structure and greater diameter of the dowels, thereby decreasing the amount of adhesive in the bonded joint. The influence of the wood species of the dowels was not statistically significant overall.

Moisture adsorption characteristics of copper-ethanolamine (Cu-EA) treated Southern yellow pine (Pinus spp.)

Holzforschung ◽  
2004 ◽  
Vol 58 (1) ◽  
pp. 32-38 ◽  
Author(s):  
J. Cao ◽  
D. P. Kamdem
Keyword(s):  
Water Vapor ◽  
Relative Humidity ◽  
Moisture Content ◽  
Treated Wood ◽  
Untreated Wood ◽  
Moisture Adsorption ◽  
Adsorption Sites ◽  
Yellow Pine ◽  
Pinus Spp ◽  
Southern Yellow Pine

Abstract Moisture adsorption isotherms were determined for untreated and copper-ethanolamine (Cu-EA) treated wood at different copper retention levels. The Cu-EA treatment reduces the water vapor accessibility in wood because copper has occupied some of the adsorption sites for moisture during the treatment. The percentage of adsorption sites occupied by copper was evaluated by M t/M u, which is the ratio of equilibrium moisture content for treated wood to untreated wood. The results show that, within the copper retention range used in this study, the M t/M u value decreases linearly at lower temperatures (4 and 15 °C) or logarithmically at higher temperatures (30 and 40 °C) with the increase of copper retention, suggesting that the percentage of adsorption sites occupied by copper (P) increases linearly or logarithmically with the copper retention in Cu-EA treated wood. P decreases with the increase of relative humidity. The reason is that more adsorption sites become available for moisture at higher relative humidity. It has also been found that the influence of Cu-EA treatment on hydrated water (M h) is more significant than that on dissolved water (M s).

Improvement in the Fock test for determining the reactivity of dissolving pulp

TAPPI Journal ◽  
2013 ◽  
Vol 12 (11) ◽  
pp. 21-26 ◽  
Author(s):  
CHAO TIAN ◽  
LINQIANG ZHENG ◽  
QINGXIAN MIAO ◽  
CHRIS NASH ◽  
CHUNYU CAO ◽  
...  
Keyword(s):  
Moisture Content ◽  
Sodium Hydroxide ◽  
Constant Temperature ◽  
Carbon Disulfide ◽  
Testing Procedure ◽  
Dissolving Pulp ◽  
Water Bath ◽  
Testing Conditions ◽  
Pulp Sample ◽  
Fock Reactivity

The Fock test is widely used for assessing the reactivity of dissolving pulp. The objective of this study was to modify the method to improve the repeatability of the test. Various parameters that affect the repeatability of the Fock test were investigated. The results showed that Fock reactivity is dependent on testing conditions affecting the xanthation between cellulose and carbon disulfide, such as the moisture content of the pulp sample, sodium hydroxide (NaOH) concentration, xanthation temperature, carbon disulfide dosage, and xanthation time. The repeatability of the test was significantly improved using the following modified testing procedure: air dried sample in the constant temperature/humidity room, xanthation temperature of 66°F (19°C) in a water bath, xanthation time of 3 h, NaOH concentration of 9% (w/w), and 1.3 mL carbon disulfide.

CATFISH DRYING (Clarias Batraclus) USING ‘TEKO BERSAYAP’ SOLAR DRYER

2012 ◽  
Vol 2 (1) ◽  
pp. 14-20
Author(s):  
Yuwana Yuwana
Keyword(s):  
Relative Humidity ◽  
Moisture Content ◽  
Ambient Temperature ◽  
Drying Rate ◽  
Drying Process ◽  
Drying Time ◽  
Ambient Relative Humidity ◽  
Solar Dryer

Experiment on catfish drying employing ‘Teko Bersayap’ solar dryer was conducted. The result of the experiment indicated that the dryer was able to increase ambient temperature up to 44% and decrease ambient relative humidity up to 103%. Fish drying process followed equations : KAu = 74,94 e-0,03t for unsplitted fish and KAb = 79,25 e-0,09t for splitted fish, where KAu = moisture content of unsplitted fish (%), KAb = moisture content of splitted fish (%), t = drying time. Drying of unsplitted fish finished in 43.995 hours while drying of split fish completed in 15.29 hours. Splitting the fish increased 2,877 times drying rate.

Algorithms to predict moisture content of grain using relative humidity time-series

2020 ◽  
Author(s):  
Charles B. Delahunt ◽  
Wenbo Wang ◽  
Simon Ghionea ◽  
Andrew Miller ◽  
Austin Chan ◽  
...  
Keyword(s):  
Time Series ◽  
Relative Humidity ◽  
Moisture Content

Determination of readiness for laying based on material moisture, corresponding relative humidity, and water release

2020 ◽  
Vol 62 (10) ◽  
pp. 1033-1040
Author(s):  
Christoph Strangfeld ◽  
Sabine Kruschwitz
Keyword(s):  
Relative Humidity ◽  
Moisture Content ◽  
Embedded Sensors ◽  
Residual Water ◽  
Floor Covering ◽  
Water Release ◽  
Content Determination ◽  
Two Samples ◽  
Moisture Content Determination

Abstract The moisture content of the subfloor has to be determined before installation to avoid damage to the floor covering. Only if readiness for layering is reached, can an installation without damage be expected in all cases. In general, three approaches exist to measure residual water content: determination of moisture content, determination of water release, or determination of the corresponding relative humidity. All three approaches are tested under laboratory conditions at eight screed types including two samples thicknesses in each case. Moisture content and water release are measured by sample weighing, the corresponding relative humidity is measured by embedded sensors. All three approaches are compared and correlated. The evaluations show only a weak correlation and, in several cases, contradicting results. Samples are considered ready for layering and not ready for layering at the same time, depending on the chosen approach. Due to these contradicting results, a general threshold for a risk of damage cannot be derived based on these measurements. Furthermore, the experiment demonstrates that the measurement of corresponding relative humidity is independent of the screed type or screed composition considered. This makes humidity measurement a potentially very promising approach for the installation of material moisture monitoring systems.

EFFECT OF MOISTURE CONTENT ON VIABILITY AND INFESTATION OF HULLESS TERRA OATS IN STORAGE

1979 ◽  
Vol 59 (4) ◽  
pp. 911-916 ◽  
Author(s):  
R. N. SINHA ◽  
N. D. G. WHITE ◽  
H. A. H. WALLACE ◽  
R. I. H. McKENZIE
Keyword(s):  
Relative Humidity ◽  
Moisture Content ◽  
Mite Infestation ◽  
Tyrophagus Putrescentiae ◽  
Adsorption And Desorption ◽  
Safe Storage ◽  
Moisture Contents ◽  
Seed Moisture ◽  
Effect Of Moisture

The effects of various seed moisture contents in hulless (cv. Terra) and hulled oats (cv. Random) on susceptibility to mite infestation and on mycofloral growth and germination loss were studied at weekly intervals. Fat acidity values were determined for Terra oats only after 4 wk of storage. Moisture content-relative humidity adsorption and desorption curves were determined for Terra at 22 °C and at relative humidities of 35–100%. Terra oats, which had a higher level of Penicillium infection at 90–100% RH than Random oats, lost viability more rapidly than Random. Fat acidity values of Terra increased rapidly from 35 mg KOH/100 g of seed to 87–118 mg KOH/100 g of seed, only when seeds were stored at 90–100% RH. Terra offered a more favorable substrate for the multiplication of the mites Tyrophagus putrescentiae, Acarus farris, and Lepidoglyphus destructor than did Random. With the exception of susceptibility to mite infestation, safe storage criteria are similar for hulled and hulless oats at usual moisture contents.

Sign in / Sign up

Export Citation Format

Share Document