scholarly journals Preparation of carbon nanotube on metal nano-dots substrate for gas sensor

2011 ◽  
Vol 36 (3) ◽  
pp. 455-458 ◽  
Author(s):  
Hiroharu Kawasaki ◽  
Takeru Kanazawa ◽  
Shin-ichi Aoqui ◽  
Ikuya Muramoto ◽  
Tamiko Ohshima ◽  
...  
Keyword(s):  
Carbon Nanotube ◽  
Gas Sensor

Carbon Nanotube Gas Sensor Fabricated on Anodic Aluminum Oxide

2007 ◽  
Vol 124-126 ◽  
pp. 1309-1312
Author(s):  
Nguyen Duc Hoa ◽  
Nguyen Van Quy ◽  
Gyu Seok Choi ◽  
You Suk Cho ◽  
Se Young Jeong ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Gas Sensor ◽  
Chemical Vapor ◽  
Fast Response ◽  
Device Fabrication ◽  
Alumina Oxide ◽  
Response And Recovery ◽  
New Type ◽  
P Type

A new type of gas sensor was realized by directly depositing carbon nanotube on nano channels of the anodic alumina oxide (AAO) fabricated on p-type silicon substrate. The carbon nanotubes were synthesized by thermal chemical vapor deposition at a very high temperature of 1200 oC to improve the crystallinity. The device fabrication process was also developed. The contact of carbon nanotubes and p-type Si substrate showed a Schottky behavior, and the Schottky barrier height increased with exposure to gases while the overall conductivity decreased. The sensors showed fast response and recovery to ammonia gas upon the filling (400 mTorr) and evacuation.

scholarly journals Simple and rapid gas sensing using a single-walled carbon nanotube field-effect transistor-based logic inverter

2021 ◽  
Author(s):  
Salomé Forel ◽  
Leandro Sacco ◽  
Alice Castan ◽  
Ileana Florea ◽  
Costel Sorin Cojocaru
Keyword(s):  
Carbon Nanotube ◽  
Power Consumption ◽  
Data Processing ◽  
Gas Sensor ◽  
Field Effect ◽  
Field Effect Transistor ◽  
Gas Sensing ◽  
Single Walled Carbon Nanotube ◽  
Effect Transistor ◽  
System Miniaturization

We design a gas sensor by combining two SWCNT-FET devices in an inverter configuration enabling a better system miniaturization together with a reduction of power consumption and ease of data processing.

ZnO doped single wall carbon nanotube as an active medium for gas sensor and solar absorber

2018 ◽  
Vol 30 (1) ◽  
pp. 147-158 ◽  
Author(s):  
K. Kaviyarasu ◽  
Genene T. Mola ◽  
S. O. Oseni ◽  
K. Kanimozhi ◽  
C. Maria Magdalane ◽  
...  
Keyword(s):  
Carbon Nanotube ◽  
Gas Sensor ◽  
Active Medium ◽  
Single Wall Carbon Nanotube ◽  
Single Wall Carbon ◽  
Solar Absorber

Fabrication of Carbon Nanotube Gas Sensor Using Step-Wise Dielectrophoretic Deposition Onto Interdigitated Pyrolyzed Carbon Electrodes

2021 ◽  
Author(s):  
Taajza Singleton ◽  
Lawrence Kulinsky
Keyword(s):  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Carbon Nanotube ◽  
Gas Sensor ◽  
Carbon Electrodes ◽  
Proof Of Concept ◽  
Nitrogen Gas ◽  
Electrical Field ◽  
The Creation ◽  
Field Lines

Abstract Carbon nanotubes (CNTs) have been implemented in the creation of many micro- and nano-devices due to their physical properties such as large volume-to-surface area as well as their high thermal and electrical conductivity. The paper describes a novel dielectrophoretic step-wise deposition of CNTs (that alternates deposition of CNTs and drying steps) between the interdigitated fingers of carbon electrodes. Multiphysics simulation illustrates the physics of CNT alignment along the electrical field lines that forms a basis for dielectrophoretic deposition of CNTs. This fabrication methodology resulted in the creation of a proof-of-concept nitrogen gas sensor.

Room-Temperature Hydrogen-Gas Sensor Based on Carbon Nanotube Yarn

2020 ◽  
Vol 20 (7) ◽  
pp. 4011-4014 ◽  
Author(s):  
Maeum Han ◽  
Jae Keon Kim ◽  
Junyeop Lee ◽  
Hee Kyung An ◽  
Jong Pil Yun ◽  
...  
Keyword(s):  
Carbon Nanotube ◽  
Gas Sensor ◽  
Room Temperature ◽  
Hydrogen Gas ◽  
Step Procedure ◽  
One Step ◽  
Cnt Arrays ◽  
Removal Of Impurities ◽  
Yarn Surface ◽  
Higher Sensitivity

The proposed study describes the development of a carbon nanotube (CNT)-based gas sensor capable of detecting the presence of hydrogen (H2) gas at room temperature. CNT yarn used in the proposed sensor was fabricated from synthesized CNT arrays. Subsequently, the yarn was treated by means of a simple one-step procedure, called acid treatment, to facilitate removal of impurities from the yarn surface and forming functional species. To verify the proposed sensor’s effectiveness with regard to detection of H2 gas at room temperature, acid-treated CNT and pure yarns were fabricated and tested under identical conditions. Corresponding results demonstrate that compared to the untreated CNT yarn, the acid-treated CNT yarn exhibits higher sensitivity to the presence of H2 gas at room temperature. Additionally, the acid-treated CNT yarn was observed to demonstrate excellent selectivity pertaining to H2 gas.

Incorporation of carbon nanotube and graphene in ZnO nanorods-based hydrogen gas sensor

2018 ◽  
Vol 44 (11) ◽  
pp. 12308-12314 ◽  
Author(s):  
Wen Chang Huang ◽  
Hsin Jie Tsai ◽  
Tien Chai Lin ◽  
Wei Chih Weng ◽  
Yu Cheng Chang ◽  
...  
Keyword(s):  
Carbon Nanotube ◽  
Gas Sensor ◽  
Zno Nanorods ◽  
Hydrogen Gas
Sign in / Sign up

Export Citation Format

Share Document