High-speed measurement of mechanical microdeformation with extended phase range using dualwavelength digital holographic interferometry

2021 ◽  
Author(s):  
Natalia Múnera ◽  
Carlos Trujillo ◽  
Jorge Garcia-Sucerquia
Keyword(s):  
Holographic Interferometry ◽  
High Speed ◽  
Extended Phase ◽  
Speed Measurement ◽  
Phase Range

scholarly journals Current-limiting amplifier for high speed measurement of resistive switching data

2021 ◽  
Vol 92 (5) ◽  
pp. 054701
Author(s):  
T. Hennen ◽  
E. Wichmann ◽  
A. Elias ◽  
J. Lille ◽  
O. Mosendz ◽  
...  
Keyword(s):  
Resistive Switching ◽  
High Speed ◽  
Limiting Amplifier ◽  
Speed Measurement ◽  
Current Limiting

Development of high speed measurement system for cell-scaffold interaction

2015 ◽  
Author(s):  
Yu Hirano ◽  
Masaru Kojima ◽  
Mitsuhiro Horade ◽  
Kazuto Kamiyama ◽  
Yasushi Mae ◽  
...  
Keyword(s):  
Measurement System ◽  
High Speed ◽  
Speed Measurement ◽  
Cell Scaffold

Ripple Technique; a Novel Non-Contact Wafer Emissivity and Temperature Method for RTP

1991 ◽  
Vol 224 ◽  
Author(s):  
C. Schietinger ◽  
B. Adams ◽  
C. Yarling
Keyword(s):  
Optical Fiber ◽  
Measurement Technique ◽  
Thermal Processing ◽  
High Speed ◽  
Rapid Thermal Processing ◽  
Wafer Surface ◽  
Speed Measurement ◽  
Temperature Method ◽  
Emissivity Measurement ◽  
Emissivity Measurements

AbstractA novel wafer temperature and emissivity measurement technique for rapid thermal processing (RTP) is presented. The ‘Ripple Technique’ takes advantage of heating lamp AC ripple as the signature of the reflected component of the radiation from the wafer surface. This application of Optical Fiber Thermometry (OFT) allows high speed measurement of wafer surface temperatures and emissivities. This ‘Ripple Technique’ is discussed in theoretical and practical terms with wafer data presented. Results of both temperature and emissivity measurements are presented for RTP conditions with bare silicon wafers and filmed wafers.

THE DESIGN AND FABRICATION OF HIGH-SPEED HBT CIRCUITS FOR FIBER-OPTIC COMMUNICATION SYSTEMS

1994 ◽  
Vol 05 (03) ◽  
pp. 253-274 ◽  
Author(s):  
MASAO OBARA ◽  
JUNKO AKAGI
Keyword(s):  
Measurement System ◽  
Communication Systems ◽  
High Speed ◽  
Fiber Optic ◽  
Heterojunction Bipolar Transistor ◽  
Fiber Amplifiers ◽  
Speed Measurement ◽  
Fiber Optic Communication ◽  
Optical Fiber Amplifiers ◽  
Optic Communication

AlGaAs/GaAs heterojunction bipolar transistor (HBT) high speed ICs have been paving the way for the most sophisticated fiber-optic communication systems since the late 1980s. Recently 20 Gbps HBT ICs have been developed to accommodate the emergence of optical fiber amplifiers. HBT technology is now proceeding towards the development of 40 Gbps systems where the lack of high speed measurement system remains an issue.

Numerical Simulation of Blast Effects on Fibre Grout Strengthened RC Panels

2017 ◽  
Vol 755 ◽  
pp. 18-30
Author(s):  
Corneliu Cismaşiu ◽  
Hugo Bento Rebelo ◽  
Válter J.G. Lúcio ◽  
Manuel T.M.S. Gonçalves ◽  
Gabriel J. Gomes ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Numerical Model ◽  
High Speed ◽  
Numerical Models ◽  
Blast Load ◽  
Measurement Equipment ◽  
Speed Measurement ◽  
Experimental Campaign ◽  
Blast Effects ◽  
Applied Element Method

The present paper aims to examine the potential of the Applied Element Method (AEM) in simulating the blast effects in RC panels. The numerical estimates are compared with the results obtained in an experimental campaign designed to investigate the effectiveness of fibre grout for strengthening full scale RC panels by comparing the effects that a similar blast load produces in a reference and the strengthened panel. First, a numerical model of the reference specimen was created in the software Extreme Loading for Structures and calibrated to match the experimental results. With no further calibration, the fibre reinforced grout strengthening was added and the resulting numerical model subjected to the same blast load. The experimental blast effects on both reference and strengthened panels, despite the lack of high speed measurement equipment (pressure, strains and displacements sensors), compare well with the numerical estimates in terms of residual and maximum displacements, showing that, once calibrated, the AEM numerical models can be successfully used to simulate blast effects in RC panels.

Sign in / Sign up

Export Citation Format

Share Document