Earthquakes and Fluid Injection1

1972 ◽  
Author(s):  
C. B. Raleigh
Keyword(s):  
Fluid Injection

A new approach to the hydraulic fracture geometric dimensions determination

2017 ◽  
Vol 12 (1) ◽  
pp. 126-134
Author(s):  
A.M. Ilyasov
Keyword(s):  
Exact Solution ◽  
Hydraulic Fracture ◽  
Pressure Gauge ◽  
Hyperbolic Type ◽  
Fluid Injection ◽  
Fracturing Fluid ◽  
New Approach ◽  
Gauge Data ◽  
Bottomhole Pressure ◽  
Half Length

Based on the generalized Perkins-Kern-Nordgren model (PKN) for the development of a hyperbolic type vertical hydraulic fracture, an exact solution is obtained for the hydraulic fracture self-oscillations after terminating the fracturing fluid injection. These oscillations are excited by a rarefaction wave that occurs after the injection is stopped. The obtained solution was used to estimate the height, width and half-length of the hydraulic fracture at the time of stopping the hydraulic fracturing fluid injection based on the bottomhole pressure gauge data.

Simulation of proppant transport and fracture plugging in the framework of a radial hydraulic fracturing model

2020 ◽  
Vol 35 (6) ◽  
pp. 325-339
Author(s):  
Vasily N. Lapin ◽  
Denis V. Esipov
Keyword(s):  
Numerical Model ◽  
Hydraulic Fracturing ◽  
Oil And Gas ◽  
Oil And Gas Industry ◽  
Injection Rate ◽  
Fluid Injection ◽  
Subtraction Technique ◽  
Gas Industry ◽  
Proppant Transport ◽  
Hydraulic Fracture Propagation

AbstractHydraulic fracturing technology is widely used in the oil and gas industry. A part of the technology consists in injecting a mixture of proppant and fluid into the fracture. Proppant significantly increases the viscosity of the injected mixture and can cause plugging of the fracture. In this paper we propose a numerical model of hydraulic fracture propagation within the framework of the radial geometry taking into account the proppant transport and possible plugging. The finite difference method and the singularity subtraction technique near the fracture tip are used in the numerical model. Based on the simulation results it was found that depending on the parameters of the rock, fluid, and fluid injection rate, the plugging can be caused by two reasons. A parameter was introduced to separate these two cases. If this parameter is large enough, then the plugging occurs due to reaching the maximum possible concentration of proppant far from the fracture tip. If its value is small, then the plugging is caused by the proppant reaching a narrow part of the fracture near its tip. The numerical experiments give an estimate of the radius of the filled with proppant part of the fracture for various injection rates and leakages into the rock.

Numerical simulation of fluid injection-induced fault slip in heterogeneous shale formations

2021 ◽  
Vol 134 ◽  
pp. 104120
Author(s):  
Yijin Zeng ◽  
Qinghua Lei ◽  
Zineng Wang ◽  
Shidong Ding ◽  
Kui Liu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Fault Slip ◽  
Fluid Injection ◽  
Shale Formations

scholarly journals Evaluating the Improvement of Cross-Correlation–Based Flow Measurement by Periodic Fluid Injection

2021 ◽  
pp. 1-21
Author(s):  
Xiong Gao ◽  
Jamie B. Coble ◽  
A. C. Hines ◽  
Belle R. Upadhyaya ◽  
J. Wesley Hines
Keyword(s):  
Flow Measurement ◽  
Cross Correlation ◽  
Fluid Injection

Dynamic Modeling of Channel Formation During Fluid Injection Into Unconsolidated Formations

SPE Journal ◽  
2015 ◽  
Vol 20 (04) ◽  
pp. 689-700 ◽  
Author(s):  
S.. Ameen ◽  
A. Dahi Taleghani
Keyword(s):  
Preferential Flow ◽  
Volume Fraction ◽  
Injection Pressure ◽  
Internal Erosion ◽  
Fluid Injection ◽  
Critical Threshold ◽  
Model Parameters ◽  
Flow Paths ◽  
Preferential Flow Paths ◽  
Stress Changes

Summary Injectivity loss is a common problem in unconsolidated-sand formations. Injection of water into a poorly cemented granular medium may lead to internal erosion, and consequently formation of preferential flow paths within the medium because of channelization. Channelization in the porous medium might occur when fluid-induced stresses become locally larger than a critical threshold and small grains are dislodged and carried away; hence, porosity and permeability of the medium will evolve along the induced flow paths. Vice versa, flowback during shut-in might carry particles back to the well and cause sand accumulation inside the well, and subsequently loss of injectivity. In most cases, to maintain the injection rate, operators will increase injection pressure and pumping power. The increased injection pressure results in stress changes and possibly further changes in channel patterns around the wellbore. Experimental laboratory studies have confirmed the presence of the transition from uniform Darcy flow to a fingered-pattern flow. To predict these phenomena, a model is needed to fill this gap by predicting the formation of preferential flow paths and their evolution. A model based on the multiphase-volume-fraction concept is used to decompose porosity into mobile and immobile porosities where phases may change spatially, evolve over time, and lead to development of erosional channels depending on injection rates, viscosity, and rock properties. This model will account for both particle release and suspension deposition. By use of this model, a methodology is proposed to derive model parameters from routine injection tests by inverse analysis. The proposed model presents the characteristic behavior of unconsolidated formation during fluid injection and the possible effect of injection parameters on downhole-permeability evolution.

Drag reduction of a nonnewtonian fluid by fluid injection on a moving wall

1999 ◽  
Vol 69 (3) ◽  
pp. 215-225 ◽  
Author(s):  
M. Akçay ◽  
M. Adil Yükselen
Keyword(s):  
Drag Reduction ◽  
Fluid Injection ◽  
Moving Wall
Sign in / Sign up

Export Citation Format

Share Document