Optimization of Diffuser Parameters for Mixing Fans in Agricultural Buildings

2018 ◽  
Vol 34 (2) ◽  
pp. 437-444 ◽  
Author(s):  
Tao Ding ◽  
Lumeng Fang ◽  
Ji-Qin Ni ◽  
Zhengxiang Shi ◽  
Baoxi Sun ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Energy Efficiency ◽  
Optimal Design ◽  
Field Test ◽  
Cfd Simulation ◽  
Maximum Flow ◽  
Uniformity Coefficient ◽  
Wind Speeds ◽  
Average Wind ◽  
Flow Flux

Abstract. Mixing fans (MFFs) are widely used in ventilation of agricultural buildings to improve the uniformity of the air supply, thereby improving the ventilation efficiency. In order to improve the ventilation performance of MFFs, a new visor-shaped diffuser was designed and installed on a MFF. The angle and the length of the diffuser were crucial parameters that affected the performance of the MFFs with the diffusers. Thereby, in this study numerical simulation with 42 diffusers of different angles (ranged from 90-270°) and different lengths (ranged from 150-650 mm) with the MFF were studied with Computational Fluid Dynamics (CFD) simulation to acquire the optimal design of diffusers. The numerical simulation results show that the diffusers of 90°/450 mm, 120°/350 mm, and 150°/250 mm with jet lengths of up to 5.85, 5.90, and 5.85 m, respectively, had better performances among all the diffusers. The optimal prototype diffusers of 90°/450 mm, 120°/350 mm, and 150°/250 mm of MFFs were tested by laboratory study and field test. The test was conducted in wind speed distributions at distances of 0.5 to 1.0 m from the axial of MFFs. During the test, we evaluated the MFFs performance such as maximum flow flux, maximum energy efficiency, and non-uniformity coefficient. The diffuser of 150°/250 mm showed the best performance, increasing the flow flux and energy efficiency by 3.8% and 11%, respectively, and obtain higher axial wind speeds and larger non-uniformity coefficients. Finally, the diffusers of 150°/250 mm were tested in a free-stall dairy barn. The field test result shows that the diffusers of 150°/250 mm increased overall average wind speeds by 7.4% and local average wind speeds at bedding 1 and bedding 2 by 31.0% and 27.7%, respectively, which agreed with our numerical simulation and laboratory test. This optimal design of mixing fans could be applied to improve the air mixing in agricultural buildings. Keywords: Agricultural buildings, Diffuser, Mixing fan, Numerical simulation, Optimization.

scholarly journals Effect of Mixed-Flow Fans with a Newly Shaped Diffuser on Heat Stress of Dairy Cows Based on CFD

Energies ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 4315 ◽  
Author(s):  
Yao ◽  
Shi ◽  
Zhao ◽  
Ding
Keyword(s):  
Energy Efficiency ◽  
Heat Stress ◽  
Dairy Cows ◽  
Cfd Simulation ◽  
Elevation Angle ◽  
Maximum Flow ◽  
Dynamics Simulation ◽  
Mixed Flow ◽  
Wind Speeds ◽  
Flow Flux

Mixed-flow fans (MFF) are widely used to reduce the heat stress in dairy cows in summer. Our research team developed MFFs with a newly shaped diffuser with the length of 250 mm and the circumferential angle of 150°, which have better performance in terms of maximum flow flux and energy efficiency. However, how the elevation angle of the diffuser influences the performance of MFFs and how the optimal fan perform in the field experiment has not been studied yet. In this paper, the diffuser was optimized by CFD (Computational Fluid Dynamics) simulation of the fan and a laboratory prototype test. An orthogonal test showed no interaction among length, circumferential angle, and elevation angle. The diffuser with an elevation angle of 10° performed better than that with an elevation angle of 0°, showing increased jet lengths, flow flux, and energy efficiency by 0.5 m, 0.69%, and 1.39%, respectively, and attaining greater axial wind speeds and better non-uniformity coefficients at the dairy cattle height. Then, through on-site controlled trials, we found that the 10°/150°/250 mm diffusers increased the overall average wind speeds by 9.4% with respect to the MFFs without a diffuser. MFFs with the newly shaped diffuser were used for field tests, and their effectiveness in alleviating heat stress in dairy cows was evaluated by testing environmental parameters and dairy cows’ physiological indicators. Although the temperature–humidity indexes (THIs) in the experimental barn with the optimized fan at different times were lower than those in the controlled barn, the environmental conditions corresponded to moderate heat stress. However, this was not consistent with cow's respiratory rate and rectal temperature. Finally, on the basis of the CFD simulation of a dairy cow barn, the equivalent temperature of cattle (ETIC), which takes into account the effect of air velocity, showed that the environment caused moderate heat stress only at 13:00, but not at other times of the day. This shows that ETIC is more accurate to evaluate heat stress.

SHAPING OF AN AUTONOMOUS POWER SYSTEM FOR GUARANTEED POWER SUPPLY WITH THE PREDOMINANCE WIND ENERGY

2018 ◽  
pp. 28-50
Author(s):  
S. G. Ignatiev ◽  
S. V. Kiseleva
Keyword(s):  
Energy Storage ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Demand ◽  
Diesel Generator ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Optimization of the autonomous wind-diesel plants composition and of their power for guaranteed energy supply, despite the long history of research, the diversity of approaches and methods, is an urgent problem. In this paper, a detailed analysis of the wind energy characteristics is proposed to shape an autonomous power system for a guaranteed power supply with predominance wind energy. The analysis was carried out on the basis of wind speed measurements in the south of the European part of Russia during 8 months at different heights with a discreteness of 10 minutes. As a result, we have obtained a sequence of average daily wind speeds and the sequences constructed by arbitrary variations in the distribution of average daily wind speeds in this interval. These sequences have been used to calculate energy balances in systems (wind turbines + diesel generator + consumer with constant and limited daily energy demand) and (wind turbines + diesel generator + consumer with constant and limited daily energy demand + energy storage). In order to maximize the use of wind energy, the wind turbine integrally for the period in question is assumed to produce the required amount of energy. For the generality of consideration, we have introduced the relative values of the required energy, relative energy produced by the wind turbine and the diesel generator and relative storage capacity by normalizing them to the swept area of the wind wheel. The paper shows the effect of the average wind speed over the period on the energy characteristics of the system (wind turbine + diesel generator + consumer). It was found that the wind turbine energy produced, wind turbine energy used by the consumer, fuel consumption, and fuel economy depend (close to cubic dependence) upon the specified average wind speed. It was found that, for the same system with a limited amount of required energy and high average wind speed over the period, the wind turbines with lower generator power and smaller wind wheel radius use wind energy more efficiently than the wind turbines with higher generator power and larger wind wheel radius at less average wind speed. For the system (wind turbine + diesel generator + energy storage + consumer) with increasing average speed for a given amount of energy required, which in general is covered by the energy production of wind turbines for the period, the maximum size capacity of the storage device decreases. With decreasing the energy storage capacity, the influence of the random nature of the change in wind speed decreases, and at some values of the relative capacity, it can be neglected.

scholarly journals Analysis of Performance of the Wind-Driven Pulverizing Aerator Based on Average Wind Speeds in the Conditions of Góreckie Lake

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2796
Author(s):  
Andrzej Osuch ◽  
Ewa Osuch ◽  
Stanisław Podsiadłowski ◽  
Piotr Rybacki
Keyword(s):  
Mathematical Model ◽  
Wind Speed ◽  
Water Pump ◽  
Average Wind Speed ◽  
Flow Rates ◽  
Wind Speeds ◽  
Average Wind ◽  
Flow Through ◽  
Analysis Of Performance ◽  
Research Period

In the introduction to this paper, the characteristics of Góreckie lake and the construction and operation of the wind-driven pulverizing aerator are presented. The purpose of this manuscript is to determine the efficiency of the pulverizing aerator unit in the windy conditions of Góreckie Lake. The efficiency of the pulverization aerator depends on the wind conditions at the lake. It was necessary to conduct thorough research to determine the efficiency of water flow through the pulverization segment (water pump). It was necessary to determine the rotational speed of the paddle wheel, which depended on the average wind speed. Throughout the research period, measurements of hourly average wind speed were carried out. It was possible to determine the efficiency of the machine by developing a dedicated mathematical model. The latest method was used in the research, consisting of determining the theoretical volumetric flow rates of water in the pulverizing aerator unit, based on average hourly wind speeds. Pulverization efficiency under the conditions of Góreckie Lake was determined based on 6600 average wind speeds for spring, summer and autumn, 2018. Based on the model, the theoretical efficiency of the machine was calculated, which, under the conditions of Góreckie Lake, amounted to 75,000 m3 per year.

scholarly journals The study of the numerical diffusion in computational calculation

2020 ◽  
Vol 310 ◽  
pp. 00039
Author(s):  
Kamila Kotrasova ◽  
Vladimira Michalcova
Keyword(s):  
Heat Transfer ◽  
Differential Equation ◽  
Numerical Simulation ◽  
Continuity Equation ◽  
Cfd Simulation ◽  
Flow Process ◽  
Ansys Fluent ◽  
Numerical Diffusion ◽  
Mesh Density ◽  
Computational Calculation

The numerical simulation of flow process and heat transfer phenomena demands the solution of continuous differential equation and energy-conservation equations coupled with the continuity equation. The choosing of computation parameters in numerical simulation of computation domain have influence on accuracy of obtained results. The choose parameters, as mesh density, mesh type and computation procedures, for the numerical diffusion of computation domain were analysed and compared. The CFD simulation in ANSYS – Fluent was used for numerical simulation of 3D stational temperature flow of the computation domain.

Numerical simulation and field test study of desulfurization wastewater evaporation treatment through flue gas

2014 ◽  
Vol 70 (7) ◽  
pp. 1285-1291 ◽  
Author(s):  
Jia-jia Deng ◽  
Liang-ming Pan ◽  
De-qi Chen ◽  
Yu-quan Dong ◽  
Cheng-mu Wang ◽  
...  
Keyword(s):  
Field Test ◽  
Flue Gas ◽  
Cfd Simulation ◽  
Electrostatic Precipitator ◽  
Negative Impact ◽  
Positive Impact ◽  
Field Tests ◽  
Gas Temperature ◽  
Simulation Results ◽  
Desulfurization Wastewater

Aimed at cost saving and pollution reduction, a novel desulfurization wastewater evaporation treatment system (DWETS) for handling wet flue gas desulfurization (WFGD) wastewater of a coal-fired power plant was studied. The system's advantages include simple process, and less investment and space. The feasibility of this system has been proven and the appropriate position and number of nozzles, the spray droplet size and flue gas temperature limitation have been obtained by computational fluid dynamics (CFD) simulation. The simulation results show that a longer duct, smaller diameter and higher flue gas temperature could help to increase the evaporation rate. The optimal DWETS design of Shangdu plant is 100 μm droplet sprayed by two nozzles located at the long duct when the flue gas temperature is 130 °C. Field tests were carried out based on the simulation results. The effects of running DWETS on the downstream devices have been studied. The results show that DWETS has a positive impact on ash removal efficiency and does not have any negative impact on the electrostatic precipitator (ESP), flue gas heat exchanger and WFGD. The pH values of the slurry of WFGD slightly increase when the DWETS is running. The simulation and field test of the DWETS show that it is a feasible future technology for desulfurization wastewater treatment.

Application and Research of Digital Technology in Optimal Design of CNC Floor Boring and Milling Machine

2012 ◽  
Vol 429 ◽  
pp. 111-115
Author(s):  
Zhen Long Leng ◽  
Jin Feng Yang ◽  
Qun Ping Liu ◽  
Xun Deng
Keyword(s):  
Numerical Simulation ◽  
Optimal Design ◽  
Digital Technology ◽  
Three Dimensional ◽  
Milling Machine ◽  
Machine Model ◽  
Digital Modeling ◽  
Key Technologies ◽  
The Cost ◽  
Interference Checking

This paper focuses on application of the three-dimensional digital modeling, numerical analysis and optimization, digital control and other key technologies which provide technical support for the design and development in CNC floor boring and milling machine manufactruing. The three-dimensional digital modeling, digital assembly, interference checking help to eliminate some hidden trouble before processing and assembly. Numerical simulation reduces the cost and shortens the cycle of designand manufactruing in the optimal design of the machine. This technique has been successfully applied to a CNC Floor Boring and Milling Machine Model, which has been running for three years and achieved satisfactary economic result.

scholarly journals Rapid coral mortality following unusually calm and hot conditions on Iriomote, Japan

F1000Research ◽  
2018 ◽  
Vol 6 ◽  
pp. 1728 ◽  
Author(s):  
Andrew H Baird ◽  
Sally A. Keith ◽  
Erika Woolsey ◽  
Ryuta Yoshida ◽  
Tohru Naruse
Keyword(s):  
Water Movement ◽  
Sea Surface ◽  
Bleaching Event ◽  
Coral Mortality ◽  
Average Wind Speed ◽  
Common Cause ◽  
Wind Speeds ◽  
Average Wind ◽  
The Mean ◽  
Low Wind Speeds

Coral bleaching can be induced by many different stressors, however, the most common cause of mass bleaching in the field is higher than average sea surface temperatures (SST). Here, we describe an unusual bleaching event that followed very calm sea conditions combined with higher than average SST. Patterns of mortality differed from typical bleaching in four ways: 1) mortality was very rapid; 2) a different suite of species were most affected; 3) tissue mortality in Acropora spp. was often restricted to the center of the colony; 4) the event occurred early in summer. The two weeks prior to the event included 8 days where the average wind speed was less than 3 ms-1. In addition, SSTs in the weeks preceding and during the event were 1.0-1.5°C higher than the mean for the last 30 years. We hypothesize that this unusual bleaching event was caused by anoxia resulting from a lack of water movement induced by low wind speeds combined with high SST.

Optimal design of selective catalyst reduction denitrification system using numerical simulation

2019 ◽  
Vol 231 ◽  
pp. 909-918 ◽  
Author(s):  
Xiang Gao ◽  
Ben Wang ◽  
Xudong Yuan ◽  
Siyuan Lei ◽  
Qinggong Qu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Optimal Design ◽  
Selective Catalyst ◽  
Catalyst Reduction

Blade Design Criteria to Compensate the Flow Curvature Effects in H-Darrieus Wind Turbines

2014 ◽  
Author(s):  
Francesco Balduzzi ◽  
Alessandro Bianchini ◽  
Riccardo Maleci ◽  
Giovanni Ferrara ◽  
Lorenzo Ferrari
Keyword(s):  
Wind Turbines ◽  
Scale Effects ◽  
Medium Size ◽  
Design Criteria ◽  
Wind Speeds ◽  
Curvature Effects ◽  
Average Wind ◽  
Energy Scenario ◽  
Flow Curvature ◽  
Real Flow

Darrieus wind turbines are experiencing a renewed interest in the wind energy scenario, in particular whenever small and medium-size installations are considered. In these contexts, the average wind speeds are generally quite low due to scale effects and therefore the most exploited design choices for the turbines are the H-shape configuration, as the entire blade can take advantage of the maximum rotational radius, and high chord to radius ratios, in order to ensure suitable Reynolds numbers on the airfoils. By doing so, the aerodynamic effects induced by the motion of the airfoils in a curved flowpath become more evident and the airfoils themselves have to be designed to compensate these phenomena if conventional design tools based on the BEM theory are used. In this study, fully unsteady 2D simulations were exploited to analyze a three-bladed H-Darrieus wind turbine in order to define the real flow structure and its effects on the turbine performance; in detail, the influence of both the virtual camber and the virtual incidence were investigated. CFD results were supported by experimental data collected on full-scale models reproducing two different airfoil mountings. Finally, the proper design criteria to compensate these phenomena are proposed and their benefits on a conventional simulation with a BEM approach are discussed.

Hydraulic Characteristics of the New Type Bulb Turbine With Micro-Head

2013 ◽  
Author(s):  
Lingyu Li ◽  
Yuan Zheng ◽  
Daqing Zhou ◽  
Zihao Mi
Keyword(s):  
Numerical Simulation ◽  
Cfd Simulation ◽  
Guide Vane ◽  
Three Dimensional ◽  
Flow Distribution ◽  
Three Dimensions ◽  
Guide Vanes ◽  
Runner Blade ◽  
Cfd Method ◽  
Bulb Turbine

The head of low-head hydropower stations is generally higher than 2.5m in the world, while micro-head hydropower resources which head is less than 2.5m are also very rich. In the paper, three-dimensional CFD method has been used to simulate flow passage of the micro-head bulb turbine. The design head and unit flow of the turbine was 1m and 3m3/s respectively. With the numerical simulation, the bulb turbine is researched by analyzing external characteristics of the bulb turbine, flow distribution before the runner, pressure distribution of the runner blade surface, and flow distribution of the outlet conduit under three different schemes. The turbine in second scheme was test by manufactured into a physical model. According to the results of numerical simulation and model test, bulb turbine with no guide vane in second scheme has simpler structure, lower cost, and better flow capacity than first scheme, which has traditional multi-guide vanes. Meanwhile, efficiency of second scheme has just little decrease. The results of three dimensions CFD simulation and test results agree well in second scheme, and higher efficiency is up to 77% which has a wider area with the head of 1m. The curved supports in third scheme are combined guide vanes to the fixed supports based on 2nd scheme. By the water circulations flowing along the curved supports which improve energy transformation ability of the runner, the efficiency of the turbine in third scheme is up to 82.6%. Third scheme, which has simpler structure and best performance, is appropriate for the development and utilization of micro-head hydropower resources in plains and oceans.

Sign in / Sign up

Export Citation Format

Share Document