scholarly journals Modification of Styrofoam Waste as a Low-Cost Adsorbent for Removal of Cadmium Ion in Aqueous Solution

2018 ◽  
Vol 3 (2) ◽  
pp. 127-142 ◽  
Author(s):  
Ismi M. N. Milla ◽  
Mia A. Syahri ◽  
Endang T. Wahyuni ◽  
Roto Roto ◽  
Dwi Siswanta
Keyword(s):  
Aqueous Solution ◽  
Sulfuric Acid ◽  
Low Cost ◽  
Diffusion Mechanism ◽  
Sulfuric Acid Concentration ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Cadmium Ion ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

waste has been modified by sulfonation using sulfuric acid to form its corresponding sulfonated adsorbent and was further used for removing cadmium ion in its aqueous solution. The effect of the styrofoam weight, sulfuric acid concentration, temperature and time on the sulfonation result was evaluated. The prepared adsorbent was characterized by XRD, FTIR, and SEM. The cadmium ion adsorption was conducted by batch technique, where the kinetic parameters were determined. The research results attribute that the sulfonated styrofoam has been successfully prepared, and the highest sulfonation is exhibited by using 18M of the sulfuric acid, at 60 oC for 6 h with 5 g of styrofoam. The cadmium adsorption by the sulfonated styrofoam fits with the pseudo-second-order and the Langmuir isotherm model, while the native styrofoam follows the intraparticle diffusion mechanism and Freundlich isotherm model. The adsorption capacities of the sulfonated and the native styrofoam are 51.6 mg/g and 7.09 mg/g respectively, and their respective adsorption rate are 8.20 10-3 mg. g-1. min-1 and 26.9 10-3 mg.g-1 min-1/2 .

scholarly journals Hydrazinolyzed cellulose-g-polymethyl acrylate as adsorbent for efficient removal of Cd(II) and Pb(II) ions from aqueous solution

2016 ◽  
Vol 75 (5) ◽  
pp. 1051-1058 ◽  
Author(s):  
Qiujin Jia ◽  
Wanting Zhang ◽  
Dongping Li ◽  
Yulong Liu ◽  
Yuju Che ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Physical Adsorption ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Initial Ph ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Adsorption Desorption ◽  
Efficient Adsorbent

Hydrazinolyzed cellulose-graft-polymethyl acrylate (Cell-g-PMA-HZ), an efficient adsorbent for removal of Cd(II) and Pb(II) from aqueous solution, has been prepared by ceric salt-initiated graft polymerization of methyl acrylate from microcrystalline cellulose surface and subsequent hydrazinolysis. The influences of initial pH, contact time, and temperature on adsorption capacity of Cell-g-PMA-HZ as well as adsorption equilibrium, kinetic and thermodynamic properties were examined in detail. As for Cd(II) adsorption, kinetic adsorption can be explained by pseudo-second-order, while adsorption isotherm fits well with Langmuir isotherm model, from which maximum equilibrium adsorption capacity can be derived as 235.85 mg g−1 at 28 °C. Further thermodynamic investigation indicated that adsorption of Cd(II) by adsorbent Cell-g-PMA-HZ is endothermic and spontaneous under studied conditions. On the other hand, isotherm of Pb(II) adsorption fits well with Freundlich isotherm model and is more likely to be a physical-adsorption-dominated process. Consecutive adsorption–desorption experiments showed that Cell-g-PMA-HZ is reusable with satisfactory adsorption capacity.

scholarly journals Eggshell Powder as an Adsorbent for Removal of Fluoride from Aqueous Solution: Equilibrium, Kinetic and Thermodynamic Studies

2012 ◽  
Vol 9 (3) ◽  
pp. 1457-1480 ◽  
Author(s):  
R. Bhaumik ◽  
N. K. Mondal ◽  
B. Das ◽  
P. Roy ◽  
K. C. Pal ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Fluoride Removal ◽  
Contaminated Water ◽  
Fluoride Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Kinetic And Thermodynamic Studies ◽  
Maximum Removal

A new medium, eggshell powder has been developed for fluoride removal from aqueous solution. Fluoride adsorption was studied in a batch system where adsorption was found to be pH dependent with maximum removal efficiency at 6.0. The experimental data was more satisfactorily fitted with Langmuir isotherm model. The kinetics and the factor controlling adsorption process fully accepted by pseudo-second-order model were also discussed. Eawas found to be 45.98 kJmol-1by using Arrhenius equation, indicating chemisorption nature of fluoride onto eggshell powder. Thermodynamic study showed spontaneous nature and feasibility of the adsorption process with negative enthalpy (∆H0) value also supported the exothermic nature. Batch experiments were performed to study the applicability of the adsorbent by using fluoride contaminated water collected from affected areas. These results indicate that eggshell powder can be used as an effective, low-cost adsorbent to remove fluoride from aqueous solution as well as groundwater.

scholarly journals Adsorption Of Cd(II) Ions From Aqueous Solution By A Low-Cost Biosorbent Prepared From Ipomea Pes-Caprae Stem

2020 ◽  
Vol 9 (3) ◽  
pp. 197-206
Author(s):  
Thaharah Ramadhani ◽  
Faisal Abdullah ◽  
Indra Indra ◽  
Abrar Muslim ◽  
Suhendrayatna Suhendrayatna ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Optimal Condition ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Low Cost ◽  
Ph Values ◽  
Monolayer Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir

The use of a low-cost biosorbent prepared from Ipomoea pes-caprae stem for the adsorption of Cd(II) ions from aqueous solution at different contact times, biosorbent sizes, pH values, and initial Cd(II) ions concentration solution was investigated. The biosorbent was analyzed using Fourier-transform infrared spectroscopy (FT-IR) to find important IR-active functional groups. A scanning electron microscope (SEM) was used to examine the biosorbent morphology. The experimental results showed the highest Cd(II) ions adsorption was 29.513 mg/g  under an optimal condition as initial Cd(II) ions concentration of 662.77 mg/L, 1 g dose, 80-min contact time, pH 5, 75 rpm of stirring speed, 1 atm, and 30 oC. Cd(II) ions' adsorption kinetics obeys the linearized pseudo-second-order kinetics (R2 = 0.996), and the adsorption capacity is based on the optimal condition, and the rate attained was 44.444 mg/g and 0.097 g/mg. Min, respectively. Besides, the adsorption isotherms were very well fitted by the linearized Langmuir isotherm model, and the monolayer adsorption capacity and pore volume determined was 30.121 mg/g and 0.129 L/mg, respectively. These results indicated the chemisorption nature

scholarly journals Kush - A Potential Biosorbent in the removal of Cd (II) and Zn (II) from aqueous solution

2012 ◽  
Vol 27 ◽  
pp. 107-114
Author(s):  
Jagjit Kour ◽  
P. L. Homagai ◽  
M. R. Pokherel ◽  
K. N. Ghimire
Keyword(s):  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Waste Streams ◽  
Adsorption Capacities ◽  
Optimum Ph ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The industrial discharge of heavy metals into waters' course is one of the major pollution problems affecting water quality. Therefore, they must be removed prior to their discharge into waste streams. An efficient and low-cost bioadsorbent has been investigated from Desmostachya bipinnata (Kush) by charring with concentrated sulphuric acid and functionalized with dimethylamine.It was characterised by SEM, FTIR and elemental analysis. The effect of pH, initial concentration and contact time of the metal solution was monitered by batch method. The maximum adsorption capacities were determined for Cd and Zn at their optimum pH 6. The equilibrium data were analysed using Langmuir and Freundlich isotherm models. Langmuir isotherm model fitted well and the rate of adsorption followed the pseudo second order kinetic equation.DOI: http://dx.doi.org/10.3126/jncs.v27i1.6669 J. Nepal Chem. Soc., Vol. 27, 2011 107-114  

The Adsorption Properties of Ciprofloxacin by KMnO4 Modified Durio zibethinus Murr Shells

2015 ◽  
Vol 1104 ◽  
pp. 111-117
Author(s):  
Wei Mei Shi ◽  
Ye Chun Ding ◽  
Long Huo Wu
Keyword(s):  
Linear Regression Analysis ◽  
Thermodynamic Characteristics ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Multilayer Adsorption ◽  
Durio Zibethinus ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Equilibrium Process ◽  
Kinetics Of

Through the experiment of Ciprofloxacin (CIP) adsorption by KMnO4modifiedDurio zibethinusMurr Shell (KDS), the best condition, adsorption kinetics and thermodynamic characteristics were studied. The isotherm parameters were estimated by linear regression analysis with Langmuir isotherm model, Temkin isotherm and Freundlich isotherm model. The equilibrium process was described well by the Freundlich isotherm model, which indicated that the adsorption thermodynamics of CIP on KDS is a multilayer adsorption process．The kinetics of the interactions showed better agreement with the pseudo-second-order model (R2=0.9999). This study demonstrated that KDS could be used for the removal of CIP in water treatment.

Adsorption of Toluene Using Low Cost Adsorbent

2012 ◽  
Author(s):  
Bassim H. Hameed ◽  
Abdul Rahman Mohamed ◽  
Hui Ying Chong
Keyword(s):  
Experimental Data ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Langmuir Model ◽  
Isotherm Model ◽  
Isotherm Models ◽  
Batch System ◽  
Key Words Toluene ◽  
Langmuir Isotherm Model ◽  
Langmuir And Freundlich Models

Kertas kerja ini membincangkan tentang kecekapan penjerap yang lebih murah, iaitu tayar getah terbuang (DRT), dalam menyingkirkan toluena daripada fasa akuas. Penjerapan toluena pada tayar getah terbuang dikaji menggunakan sistem berkelompok pada suhu 25°C dan 30°C. Daripada kajian ini, didapati toluena dapat disingkirkan sehingga 70% dengan menggunakan julat kepekatan awalan antara 50 mg/l hingga 300 mg/l. Dengan menggunakan model keseimbangan terlelurus, iaitu model Langmuir dan Freundlich, keupayaan penjerapan maksimum dapat ditentukan. Daripada data eksperimen, terbukti bahawa walaupun kedua–dua model isoterma Langmuir dan Freundlich boleh menjelaskan data isoterma, tetapi penjerapan toluena pada DRT dapat ditunjukkan dengan lebih baik oleh isoterma Freudlich. Bagi nilai K Freundlich, keupayaan penjerapan ialah 6.6374 mg/l dan 7.7535 mg/l, pada suhu 25°C dan 30°C. Nilai eksponen n Freudlich adalah lebih daripada satu untuk kedua–dua suhu. Kata kunci: Toluena, penjerapan, isoterma, tayar getah terbuang, model isoterma Langmuir, model isoterma Freundlich This paper discusses the effectiveness of a less expensive adsorbent, a discarded rubber tyre (DRT) in removing toluene from aqueuos phase. Adsorption of toluene on a DRT has been studied by using batch system at 25 and 30°C. It was found that up to 70% of toluene was removed for the range of toluene initial concentrations studied between 50–300 mg/l. Using linearized forms of equilibrium models, namely Langmuir and Freundlich models, the maximum adsorptive capacities were determined. It was evident from the experimental data that, although both Langmuir and Freundlich isotherm models could describe the isotherm data, the adsorption of toluene on a DRT was described well by the Freundlich isotherm. For Freundlich K values, sorption capacities were 6.6374 and 7.7535 mg/l at 25 and 30°C, respectively. The values of Freundlich exponent n were greater than one for both temperatures. Key words: Toluene, adsoprtion, isotherms, discarded rubber tyre, Langmuir isotherm model, Freundlich isotherm model

Study of the kinetics and the adsorption isotherm of cadmium(II) from aqueous solution using green algae (Ulva lactuca) biomass

2015 ◽  
Vol 72 (9) ◽  
pp. 1505-1515 ◽  
Author(s):  
H. Asnaoui ◽  
A. Laaziri ◽  
M. Khalis
Keyword(s):  
Aqueous Solution ◽  
Metal Ions ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Ulva Lactuca ◽  
Order Kinetic ◽  
Solution Ph ◽  
Algae Biomass ◽  
Pseudo Second Order

Batch experiments were conducted to study the adsorption of hazardous cadmium onto low-cost algae biomass in aqueous solution with respect to concentration of adsorbate, adsorbent dosage, contact time, solution pH and temperature. Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the isotherm constants were determined. The activation energy of adsorption was also evaluated for the adsorption of cadmium onto Ulva lactuca biomass. Experimental data were tested in terms of biosorption kinetics using pseudo-first-order and pseudo-second-order kinetic models. The results showed that the biosorption processes of Cd(II) followed well pseudo-second-order kinetics. Langmuir and Freundlich models were applied to describe the biosorption isotherm of the metal ions by Ulva lactuca biomass. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The biosorption capacity of Ulva lactuca biomass for cadmium was found to be 3.02 mg/g at pH 5.60 min equilibrium time and 20 °C. The mean free energy which was calculated was 6.24 kJ/mol for Cd(II) biosorption, which shows that the adsorption is physical. The calculated thermodynamic parameters (ΔG0, ΔH0 and ΔS0) showed that the biosorption of Cd(II) onto Ulva lactuca biomass was feasible, spontaneous and exothermic under examined conditions. The results indicate that algae Ulva lactuca could be employed as a low-cost material for the removal of metal ions from aqueous solution.

scholarly journals Equilibrium and Kinetic Study of Removal Copper(II) from Aqueous Solution Using Chicken Eggshells: Low Cost Sorbent

Molekul ◽  
2021 ◽  
Vol 16 (1) ◽  
pp. 28
Author(s):  
Mohammad Jihad Madiabu ◽  
Joko Untung ◽  
Imas Solihat ◽  
Andi Muhammad Ichzan
Keyword(s):  
Aqueous Solution ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Sorption Process ◽  
X Ray Diffraction ◽  
Order Model ◽  
X Ray ◽  
Adsorption Condition ◽  
Pseudo Second Order ◽  
Effect Of Copper

The research aims to investigate feasibility eggshells as potential adsorbent to remove copper(II) ions from aqueous solution. Eggshells powder was characterized using X-ray diffraction, scanning electron microscopy, and Fourier transform infrared spectroscopy. Effect of copper(II) initial concentration, adsorbent dosage, and contact time have conducted. The optimum adsorption condition obtained when 0.7 g eggshells applied to 50 mg/L copper(II) solution for 50 minutes. The maximum percentage of copper(II) removal was exceeded more than 85%. Langmuir and Freundlich isotherm model were applied to describe the equilibrium adsorption. Copper(II) kinetics sorption process was fitted to pseudo-second order model with a rate constant equal to 0.516 g/mg.min. The results clearly exhibit that eggshells powder can be effectively used to remove copper(II) ions from aqueous solutions.

The Kinetics and Isotherms of Adsorption of Sb(III) from Aqueous Solutions onto the Porous Biomorph-Genetic Composite of Fe2O3/Fe3O4/C with Bamboo Template

2013 ◽  
Vol 394 ◽  
pp. 8-13
Author(s):  
Zong Qiang Zhu ◽  
Shuang Cao ◽  
Wen Hui Wei ◽  
Yi Nian Zhu
Keyword(s):  
Kinetic Curve ◽  
Equilibrium Concentration ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Change Trend ◽  
Kinetics And Isotherms ◽  
Kinetics Of

Static adsorption of Sb (III) on a porous biomorph-genetic composite of Fe2O3/Fe3O4/C (PBGC-Fe/C-B) was studied. The results showed that the kinetic curve of Sb (III) adsorption by PBGC-Fe/C-B had same change trend under initial concentration of 5, 10 and 50 mg/L. The fitting and regression analysis of four kinds of kinetic model indicated that, the adsorption kinetics of Sb (III) by the PBGC-Fe/C-B well follow the pseudo-second-order model (R2>0.9999). At different reaction temperature (25 °C, 35 °C and 45 °C), the adsorption capacity of Sb (III) by PBGC-Fe/C-B both increased with increasing the solution equilibrium concentration. While it showed a declined tendency with temperature increased. The Langmuir isotherm model (R2>0.98) and the Freundlich isotherm model (R2>0.95) had both better fitted with the equilibrium data.

UTILIZATION OF DURIAN PEEL AS POTENTIAL ADSORBENT FOR BISPHENOL A REMOVAL IN AQUOEUS SOLUTION

2015 ◽  
Vol 74 (11) ◽  
Author(s):  
Zainab Mat Lazim ◽  
Tony Hadibarata ◽  
Mohd Hafiz Puteh ◽  
Zulkifli Yusop ◽  
Riry Wirasnita ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Sulfuric Acid ◽  
Low Cost ◽  
Agricultural Waste ◽  
Order Type ◽  
Batch Adsorption ◽  
Operational Parameters ◽  
Before And After ◽  
Pseudo Second Order ◽  
Solution Kinetic

This study explored the low-cost adsorbent of durian peel for BPA removal from aqueous solutions. The effect of various operational parameters such as contact time, temperature, concentration, agitation and pH on the adsorption of BPA was investigated using the batch adsorption study. It was found that Durian peel can be used as a low cost adsorbent for the removal of BPA in aqueous solution after treated with sulfuric acid. The effects of morphology, functional groups, and surface area of adsorbent, before and after pretreatment with sulfuric acid and reaction were investigated by using FESEM, FTIR, and BET. The present study indicates that durian peel had removed 69.63% of BPA with adsorption capacity of 4.178 mg/g for 24 hours. The result proved that this treated agricultural waste was promising material as an alternative adsorbent for the removal of BPA from aqueous solution. Kinetic study of the results gave a pseudo-second order type of mechanism while the adsorption characteristics of the adsorbent followed the Langmuir adsorption isotherm.

Sign in / Sign up

Export Citation Format

Share Document