scholarly journals Stannous Oxide Thick Film Nanosensors Design by Screen Printing Technology: Structural, Electrical Parameters and H2s Gas Detection Study

2021 ◽  
Vol 18 (1) ◽  
pp. 66-74
Author(s):  
Umesh Jagannath Tupe ◽  
Arun Vitthal Patil ◽  
Madhukar Sarvottam Zambare ◽  
Prashant Bhimrao Koli
Keyword(s):  
Hydrogen Sulfide ◽  
Thick Film ◽  
Screen Printing ◽  
Sno2 Nanoparticles ◽  
Average Particle Size ◽  
Cost Effective ◽  
Surface Characteristic ◽  
Precipitation Method ◽  
Average Particle ◽  
Stannous Oxide

The present research deals with the fabrication of stannous oxide nanoparticles by conventional and cost effective co precipitation method. The thick film sensors of SnO2 nanoparticles were prepared by standard screen-printing technique by photolithography. The prepared SnO2 material was characterized by several techniques to confirm the structural properties. Initially, the prepared nanoparticles of SnO2 were investigated by x-ray diffraction technique to confirm the synthesis of prepared material within nanoscale. From XRD data the average particle size of prepared thick films was found to be 21.87 nm calculated using Debye-Scherer formula. The material was further characterized by using scanning electron microscopy (SEM) to investigate the structural and surface characteristic of SnO2. SEM data clearly indicates the heterogeneous surface, and some voids present over the surface of SnO2 nanoparticles. The Fourier transfer infra red technique was employed to investigate the metal oxygen frequency of SnO2 material. The prepared sensor was exclusively utilized to sense the hydrogen sulfide gas vapors at various concentrations. The prepared sensor was found to be highly sensitive to H2S vapors nearly 63.8% sensitivity was recorded. The response and recovery study shows the response time of 9 seconds and recovery time of 19 seconds for hydrogen sulfide gas vapors. The SnO2 sensor was further utilized for recycling performance to get the firm results of sensitivity in four turns with period of 15 days.

Zn-doped SnO2 nanoparticles: Structural, optical, dielectric and magnetic properties

2017 ◽  
Vol 31 (30) ◽  
pp. 1750234 ◽  
Author(s):  
Zulfiqar ◽  
Yuliang Yuan ◽  
Zainab Iqbal ◽  
Jianguo Lu
Keyword(s):  
Particle Size ◽  
Magnetic Properties ◽  
Defect Density ◽  
Sno2 Nanoparticles ◽  
Average Particle Size ◽  
Dielectric Materials ◽  
Precipitation Method ◽  
Average Particle ◽  
Zn Content ◽  
Optical Dielectric

Zn-doped SnO2 nanoparticles have been synthesized by the chemical precipitation method with the Zn contents ([Formula: see text]) of 1, 2 and 4 wt.%. The nanoparticles are crystalline in all cases, with the average particle size decreasing from 13.4 nm to 7.71 nm as the Zn concentration increases. The visible photoluminescence emission is observed in Zn-doped SnO2 nanoparticles, with larger emission intensity at elevated Zn content. The dielectric constant has a strong doping dependence, which is evidently enhanced with increasing Zn content. Magnetization measurements reveal the enhancement in saturation magnetization and remanence magnetization, while the reduction in coercive field is observed with increasing amount of Zn dopant. The variation of optical, dielectric and magnetic properties is due to the incorporation of Zn in SnO2 with smaller particle size and higher defect density. The present study clearly reveals the doping-induced ferromagnetism in Zn-doped SnO2 nanoparticles, having applications in ultrahigh dielectric materials, high frequency devices and spintronics.

scholarly journals Developing of buffer-precipitation method for lead metaborate (Pb(BO2)2 H2O) nanostructures

2020 ◽  
Vol 38 (1) ◽  
pp. 138-142
Author(s):  
Berna Bulbul ◽  
Seda Beyaz
Keyword(s):  
Inductively Coupled Plasma ◽  
Average Particle Size ◽  
Particle Surface ◽  
Synthesis Method ◽  
Cost Effective ◽  
Precipitation Method ◽  
Average Particle ◽  
Gravimetric Analysis ◽  
Reflectance Measurement ◽  
Vis Spectroscopy

AbstractAmorphous lead metaborate (Pb(BO2)2 H2O) nanostructures were synthesized by a simpl and cost-effective synthesis method which is based on precipitation of lead ions using boric acid/sodium hydroxide buffer (pH 9.2) in the presence of polyethylene glycol (PEG). Scanning electron microscopy images showed that the average particle size is 30±9 nm and the particle shape is mostly spherical. The chemical formulation of Pb(BO2)2 H2O was confirmed by infrared spectroscopy, inductively coupled plasma and thermal gravimetric analysis (TGA). The percentage of PEG molecules on the particle surface equal to 2.5 % was determined by TGA. Optical reflectance measurement was performed by UV-Vis spectroscopy. Based on the Kubelka-Munk function, it was calculated that the Pb(BO2)2 H2O nanostructures have a direct band gap of 4.6 eV.

Enhanced oral bioavailability of nisoldipine-piperine-loaded poly-lactic-co-glycolic acid nanoparticles

2017 ◽  
Vol 6 (6) ◽  
pp. 517-526 ◽  
Author(s):  
Permender Rathee ◽  
Anjoo Kamboj ◽  
Shabir Sidhu
Keyword(s):  
Oral Bioavailability ◽  
Drug Loading ◽  
Average Particle Size ◽  
Entrapment Efficiency ◽  
Pharmacokinetic Interaction ◽  
Precipitation Method ◽  
Pharmacokinetic Studies ◽  
Average Particle

AbstractBackground:Piperine helps in the improvement of bioavailability through pharmacokinetic interaction by modulating metabolism when administered with other drugs. Nisoldipine is a substrate for cytochrome P4503A4 enzymes. The study was undertaken to assess the influence of piperine on the pharmacokinetics and pharmacodynamics of nisoldipine nanoparticles in rats.Methods:Optimization studies of nanoparticles were performed using Taguchi L9 orthogonal array, and the nanoparticles were formulated by the precipitation method. The influence of piperine and nanoparticles was evaluated by means of in vivo kinetic and dynamic studies by oral administration in rats.Results:The entrapment efficiency, drug loading, ζ potential, and average particle size of optimized nisoldipine-piperine nanoparticles was 89.77±1.06%, 13.6±0.56%, −26.5 mV, and 132±7.21 nm, respectively. The in vitro release in 0.1 n HCl and 6.8 pH phosphate buffer was 96.9±0.48% and 98.3±0.26%, respectively. Pharmacokinetic studies showed a 4.9-fold increase in oral bioavailability and a >28.376±1.32% reduction in systemic blood pressure by using nanoparticles as compared to control (nisoldipine suspension) in Wistar rats.Conclusion:The results revealed that piperine being an inhibitor of cytochrome P4503A4 enzymes enhanced the bioavailability of nisoldipine by 4.9-fold in nanoparticles.

scholarly journals Textiles Printing Using Microencapsulated Pigments in Biodegradable Thickeners

2018 ◽  
Vol 15 (1) ◽  
pp. 6122-6129 ◽  
Author(s):  
Meram S. Abdelrahman ◽  
Sahar Nassar ◽  
Hamada Mashaly ◽  
Safia Mahmoud ◽  
Dalia Maamoun
Keyword(s):  
Screen Printing ◽  
Average Particle Size ◽  
Morphological Structure ◽  
Core Material ◽  
Average Particle ◽  
X Ray ◽  
Screen Printing Technique ◽  
Printing Technique ◽  
Encapsulation Process ◽  
Dispersing Agents

Micro-encapsulated pigments were formulated into biodegradable printing pastes and their properties were analyzed. The pigment was used as the core material and polylactic-based biodegradable thickener was used as the wall-former. Cotton/polyester blend fabric was printed with micro-encapsulated pigment using screen-printing technique without dispersing agents, penetrating agents, leveling agents or other auxiliaries. Micro-encapsulated pigment has been characterized in terms of average particle size and size distribution, morphological structure and elemental composition using scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX). The variations in viscosity and paste stability were observed upon storing over 7 days at ambient temperature. For permanence, the micro-encapsulation process afforded better colorfastness properties against light, washing, rubbing, and perspiration.

scholarly journals Preparation and characterization of domperidone nanoparticles for dissolution improvement

2018 ◽  
Vol 27 (1) ◽  
pp. 39-52
Author(s):  
Mohammed Sabar Al-lami ◽  
Malath H. Oudah ◽  
Firas A. Rahi
Keyword(s):  
Particle Size ◽  
Average Particle Size ◽  
In Vitro Release ◽  
Methyl Cellulose ◽  
Precipitation Method ◽  
Average Particle ◽  
Antisolvent Precipitation ◽  
Stirring Time

This study was carried out to prepare and characterize domperidone nanoparticles to enhance solubility and the release rate. Domperidone is practically insoluble in water and has low and an erratic bioavailability range from 13%-17%. The domperidone nanoparticles were prepared by solvent/antisolvent precipitation method at different polymer:drug ratios of 1:1 and 2:1 using different polymers and grades of poly vinyl pyrolidone, hydroxy propyl methyl cellulose and sodium carboxymethyl cellulose as stabilizers. The effect of polymer type, ratio of polymer:drug, solvent:antisolvent ratio, stirring rate and stirring time on the particle size, were investigated and found to have a significant (p? 0.05) effect on particle size. The best formula was obtained with lowest average particle size of 84.05. This formula was studied for compatibility by FTIR and DSC, surface morphology by FESEM and crystalline state by XRPD. Then domperidone nanoparticles were formulated into a simple capsule dosage form in order to study of the in vitro release of drug from nanoparticles in comparison raw drug and mixture of polymer:drug ratios of 2:1. The release of domperidone from best formula was highly improved with a significant (p? 0.05) increase.

Synthesis of Nanostructured Magnetic Mixed-Oxide Ferrite Powders by Using A Novel Chemical Method

2002 ◽  
Vol 720 ◽  
Author(s):  
N N Ghosh
Keyword(s):  
Particle Size ◽  
Mixed Oxide ◽  
Chemical Method ◽  
Average Particle Size ◽  
Cost Effective ◽  
Water Soluble ◽  
Average Particle ◽  
Chemical Route ◽  
Water Soluble Polymer ◽  
Different Temperatures

AbstractIn the present investigation, an attempt has been made to establish a new chemical route for synthesis of the nanostructured mixed oxide ferrite powders. By using this chemical method a variety of ferrite powders having spinel structure and doped with Co, Ni, Mn, Zn etc has been prepared. In this method nitrate salts of the different metals were used as starting materials. The aqueous solutions of the metal nitrates were mixed according to the molar ration of the compositions. Then the mixtures were mixed with an aqueous solution of water soluble polymer (polyvinyl alcohol). This mixture after drying yield fluffy brown powders. These powders were then calcined at different temperatures ranging from 400 °C to 700 °C. Nanostructured powders were obtained from the thermal decomposition of the brown powders. The powders, prepared by calcinations at different temperatures, were characterized by using X-Ray diffraction analysis, IR spectroscopy, TGA/DTA, and TEM. It was observed that the average particle size of the powders are in nanometer scale with a narrow size distribution. The average particle size of the powders was increased with the increase of calcinations temperature.This chemical method has proved to provide a convenient process for the preparation of nanostructured ceramic powders at comparatively low temperatures and offers the potential of being a simple and cost-effective route.

Morphology-Controlled CaCO3 Nanostructures by Modified Co-Precipitation in Pulsed Mode

2015 ◽  
Vol 752-753 ◽  
pp. 148-153
Author(s):  
M.M. Nassar ◽  
Taha Ebrahiem Farrag ◽  
M.S. Mahmoud ◽  
Sayed Abdelmonem
Keyword(s):  
Particle Size ◽  
Calcium Carbonate ◽  
Rotation Speed ◽  
Average Particle Size ◽  
Calcium Nitrate ◽  
Precipitation Method ◽  
Average Particle ◽  
X Ray ◽  
Co Precipitation ◽  
Pulsed Mixing

Calcium carbonate nanoparticles and nanorods were synthesized by precipitation from saturated sodium carbonate and calcium nitrate aqueous solutions through co precipitation method. A new rout of synthesis was done by both using pulsed mixing method and controlling the addition of calcium nitrate. The effect of the agitation speed, and the temperature on particle size and morphology were investigated. Particles were characterized using X-ray Microanalysis, X-ray analysis (XRD) and scanning electron microscopy (SEM). The results indicated that increasing the mixer rotation speed from 3425 to 15900 (rpm) decreases the average particle size to 64±7 nm. A rapid nucleation then aggregation induced by excessive shear force phenomena could explain this observation. Moreover, by increasing the reaction temperature, the products were converted from nanoparticle to nanorods. The maximum attainable aspect ratio was 6.23 at temperature of 75°C and rotation speed of 3425. Generally, temperature raise promoted a significant homoepitaxial growth in one direction toward the formation of calcite nanorods. Overall, this study can open new avenues to control the morphology of the calcium carbonate nanostructures.

Grain Size Control and Ethanol Sensing Properties of Calcined SnO2 Nanoparticles

2011 ◽  
Vol 266 ◽  
pp. 76-79
Author(s):  
Yu Wang ◽  
Xiao Lin Jia ◽  
Lin Dong ◽  
Shao Kang Guan
Keyword(s):  
Sno2 Nanoparticles ◽  
Sol Gel ◽  
Average Particle Size ◽  
Size Control ◽  
High Sensitivity ◽  
Average Particle ◽  
Nanocrystal Growth ◽  
Grain Size Control ◽  
Concentration Detection Limit ◽  
Ethanol Sensing

SnO2 nanoparticles were prepared via a sol-gel method by heating the mixture of hydrous SnO2 nanoparticles and SiO2 nanospheres at 600 °C. The average particle size of the obtained SnO2 nanoparticles is 3.3 nm, smaller than that of the SnO2 nanoparticles (~ 6.4 nm) prepared by calcining the pure hydrous SnO2 at 600 °C. The SiO2 nanospheres play an important role in restricting SnO2 nanocrystal growth. The ~3.3 nm-sized SnO2 nanoparticles exhibited high sensitivity for ethanol as well as quick response and recovery time. The concentration detection limit can be as low as 5 ppm at room temperature.

scholarly journals Facile Preparation of CNT/Ag2S Nanocomposites with Improved Visible and NIR Light Photocatalytic Degradation Activity and Their Catalytic Mechanism

Micromachines ◽  
2019 ◽  
Vol 10 (8) ◽  
pp. 503 ◽  
Author(s):  
Lijing Di ◽  
Tao Xian ◽  
Xiaofeng Sun ◽  
Hongqin Li ◽  
Yongjie Zhou ◽  
...  
Keyword(s):  
Catalytic Mechanism ◽  
Dye Degradation ◽  
Average Particle Size ◽  
Hybrid Nanocomposites ◽  
Light Irradiation ◽  
Precipitation Method ◽  
Average Particle ◽  
Nir Light ◽  
Photocatalytic Activities ◽  
Ag2s Nanoparticles

In this work, a series of carbon nanotubes (CNT)/Ag2S hybrid nanocomposites were successfully prepared by a facile precipitation method. Transmission electron microscope (TEM) observation indicates that Ag2S nanoparticles with an average particle size of ~25 nm are uniformly anchored on the surface of CNT. The photocatalytic activities of the CNT/Ag2S nanocomposites were investigated toward the degradation of rhodamine B (RhB) under visible and near-infrared (NIR) light irradiation. It is shown that the nanocomposites exhibit obviously enhanced visible and NIR light photocatalytic activities compared with bare Ag2S nanoparticles. Moreover, the recycling photocatalytic experiment demonstrates that the CNT/Ag2S nanocomposites possess excellent photocatalytic stability. The photoelectrochemical and photoluminescence measurements reveal the efficient separation of photogenerated charges in the CNT/Ag2S nanocomposites. This is the dominant reason behind the improvement of the photocatalytic activity. Based on active species trapping experiments, the possible photocatalytic mechanism of CNT/Ag2S nanocomposites for dye degradation under visible and NIR light irradiation was proposed.

Evaluation of the Antimicrobial Activity of Citric Acid Functionalized Magnetite Nanoparticles

2020 ◽  
Vol EJMM29 (4) ◽  
pp. 143-149
Author(s):  
Ahmed M. El-Khawaga ◽  
Ayman A. Farrag ◽  
Ahmed I. El-Batal ◽  
Mohamed A. Elsayed
Keyword(s):  
Antimicrobial Activity ◽  
Citric Acid ◽  
Magnetite Nanoparticles ◽  
Pathogenic Bacteria ◽  
Average Particle Size ◽  
Maximum Activity ◽  
Precipitation Method ◽  
Average Particle ◽  
Effective Prevention ◽  
Fe3o4 Nps

Background: Antimicrobial resistance (AMR) has emerged as one of the principal public health problems of the 21st century that threatens the effective prevention and treatment of an ever-increasing range of infections caused by bacteria no longer susceptible to the common medicines used to treat them. Objectives: To development of Fe3O4 NPs with specific sizes and shapes Potential as a new antibacterial agent. Methodology: In this study magnetite nanoparticles (Fe3O4 NPs) were synthesized through an aqueous co-precipitation method and functionalized with citric acid for outstanding their antimicrobial potential. Fe3O4 NPs were characterized by XRD, TEM, SEM, EDX and FTIR to analyze crystallinity, average particle size, morphology and functional groups, respectively. Antimicrobial activity was investigated against pathogenic bacteria as zone of inhibition (ZOI) and minimum inhibitory concentration (MIC). Results: Antimicrobial results showed that CA- Fe3O4 NPs owns maximum activity against Staphylococcus aureus and E. coli by 18.0 and 15.0mm ZOI, respectively. Conclusion: It should be noted that (CA-Fe3O4) NPs are also active upon Gram-positive than Gram- negative bacteria. The synthesized (CA-Fe3O4) NPs are promising for potential applications as antimicrobial agent and in drug delivery fields.

Sign in / Sign up

Export Citation Format

Share Document