scholarly journals Factors Affecting Diametral Tensile Strength of Microfilled Dental Composites

1996 ◽  
Vol 28 (4) ◽  
pp. 293-298 ◽  
Author(s):  
Jyongsik Jang ◽  
Sangwoo Kim
Keyword(s):  
Tensile Strength ◽  
Dental Composites ◽  
Factors Affecting ◽  
Diametral Tensile Strength

Diametral tensile strength and dental composites

1987 ◽  
Vol 3 (1) ◽  
pp. 46-48 ◽  
Author(s):  
R.W. Penn ◽  
R.G. Craig ◽  
J.A. Tesk
Keyword(s):  
Tensile Strength ◽  
Dental Composites ◽  
Diametral Tensile Strength

scholarly journals The Influence of Various Photoinitiators on the Properties of Commercial Dental Composites

Polymers ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3972
Author(s):  
Andrea Kowalska ◽  
Jerzy Sokolowski ◽  
Tomasz Gozdek ◽  
Michał Krasowski ◽  
Karolina Kopacz ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Biomechanical Properties ◽  
Dental Composites ◽  
Polymerization Shrinkage ◽  
Contraction Stress ◽  
Photoelastic Analysis ◽  
Diametral Tensile Strength

The aim of this article was to compare the biomechanical properties of commercial composites containing different photoinitiators: Filtek Ultimate (3M ESPE) containing camphorquinone (CQ); Estelite Σ Quick (Tokuyama Dental) with CQ in RAP Technology®; Tetric EvoCeram Bleach BLXL (Ivoclar Vivadent AG) with CQ and Lucirin TPO; and Tetric Evoceram Powerfill IVB (Ivoclar Vivadent AG) with CQ and Ivocerin TPO. All samples were cured with a polywave Valo Lamp (Ultradent Products Inc.) with 1450 mW/cm2. The microhardness, hardness by Vicker’s method, diametral tensile strength, flexural strength and contraction stress with photoelastic analysis were tested. The highest hardness and microhardness were observed for Filtek Ultimate (93.82 ± 17.44 HV), but other composites also displayed sufficient values (from 52 ± 3.92 to 58,82 ± 7.33 HV). Filtek Ultimate not only demonstrated the highest DTS (48.03 ± 5.97 MPa) and FS (87.32 ± 19.03 MPa) but also the highest contraction stress (13.7 ± 0.4 MPa) during polymerization. The TetricEvoCeram Powerfill has optimal microhardness (54.27 ± 4.1 HV), DTS (32.5 ± 5.29 MPa) and FS (79.3 ± 14.37 MPa) and the lowest contraction stress (7.4 ± 1 MPa) during photopolymerization. To summarize, Filtek Ultimate demonstrated the highest microhardness, FS and DTS values; however, composites with additional photoinitiators such as Lucirin TPO and Ivocerin have the lowest polymerization shrinkage. These composites also have higher FS and DTS and microhardness than material containing CQ in Rap Technology.

Effect of the incorporation of hydroxyapatite on the diametral tensile strength of conventional and hybrid glass ionomer cements

Odontology ◽  
2021 ◽  
Author(s):  
Matias Mederos ◽  
Carlos Enrique Cuevas-Suarez ◽  
Walter Sanchez ◽  
Pablo Miranda ◽  
Alejandro Francia ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Glass Ionomer Cements ◽  
Glass Ionomer ◽  
Diametral Tensile Strength

scholarly journals Flexural and diametral tensile strength of composite resins

2008 ◽  
Vol 22 (1) ◽  
pp. 84-89 ◽  
Author(s):  
Álvaro Della Bona ◽  
Paula Benetti ◽  
Márcia Borba ◽  
Dileta Cecchetti
Keyword(s):  
Tensile Strength ◽  
Composite Resins ◽  
Diametral Tensile Strength

scholarly journals Assessment of the mechanical properties of glass ionomer cements for orthodontic cementation

2012 ◽  
Vol 17 (6) ◽  
pp. 154-159 ◽  
Author(s):  
Marcel M. Farret ◽  
Eduardo Martinelli de Lima ◽  
Eduardo Gonçalves Mota ◽  
Hugo Mitsuo S. Oshima ◽  
Gabriela Maguilnik ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Bond Strength ◽  
Shear Bond Strength ◽  
Glass Ionomer Cements ◽  
Glass Ionomer ◽  
Resin Modified Glass Ionomer ◽  
Strength Tests ◽  
Diametral Tensile Strength

OBJECTIVE: To evaluate the mechanical properties of three glass ionomers cements (GICs) used for band cementation in Orthodontics. METHODS: Two conventional glass ionomers (Ketac Cem Easy mix/3M-ESPE and Meron/Voco) and one resin modified glass ionomer (Multi-cure Glass ionomer/3M-Unitek) were selected. For the compressive strength and diametral tensile strength tests, 12 specimens were made of each material. For the microhardness test 15 specimens were made of each material and for the shear bond strength tests 45 bovine permanent incisors were used mounted in a self-cure acrylic resin. Then, band segments with a welded bracket were cemented on the buccal surface of the crowns. For the mechanical tests of compressive and diametral tensile strength and shear bond strength a universal testing machine was used with a crosshead speed of 1,0 mm/min and for the Vickers microhardness analysis tests a Microdurometer was used with 200 g of load during 15 seconds. The results were submitted to statistical analysis through ANOVA complemented by Tukey's test at a significance level of 5%. RESULTS: The results shown that the Multi-Cure Glass Ionomer presented higher diametral tensile strength (p < 0.01) and compressive strength greater than conventional GICs (p = 0.08). Moreover, Ketac Cem showed significant less microhardness (p < 0.01). CONCLUSION: The resin-modified glass ionomer cement showed high mechanical properties, compared to the conventional glass ionomer cements, which had few differences between them.

scholarly journals Pentaerythritol Tetrasalicylate in the Chemical Composition of Root Canal Sealers

2018 ◽  
Vol 29 (1) ◽  
pp. 48-53
Author(s):  
Manuela Gonçalves de Souza e Silva ◽  
Eliseu Aldrighi Münchow ◽  
Rafael Pino Vitti ◽  
Mário Alexandre Coelho Sinhoreti ◽  
Evandro Piva ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Young’S Modulus ◽  
Root Canal ◽  
Methyl Salicylate ◽  
Young's Modulus ◽  
Setting Time ◽  
Molar Ratio ◽  
Resonance Spectroscopy ◽  
Root Canal Sealers ◽  
Diametral Tensile Strength

Abstract The aim of this study was to synthesize and evaluate physicochemical properties of a new salicylate derivative in experimental calcium-based root canal sealers. Two salicylate derivatives were synthesized for the transesterification reaction of methyl salicylate with two different alcohols (1,3-butylenoglicol disalicylate-BD and pentaerythritol tetrasalicylate -PT) in molar ratio 1:3 and 1:6, respectively. The products (BD and PT), were characterized by Fourier Transform Infrared Spectroscopy (FTIR) and Nuclear Magnetic Resonance spectroscopy (RMN). Calcium-based experimental sealers were prepared with the same catalyst paste (60% of MTA, 39% of n-ethyl-o-toluenesulfonamide, and 1% titanium dioxide) and four different concentrations of BD and PT in the base pastes (40/0 - control, 35/5, 30/10 and 20/20) with 60% of bismuth oxide. The experimental sealers were evaluated for setting time, solubility (24 h, 7, 14 and 30 days), diametral tensile strength and Young’s Modulus. Data were analyzed by one- or two-way ANOVA with Tukey’s test (p<0.05). The addition of PT reduced the materials setting time. After 24 h the sealer 40/0 and 35/5 had higher solubility, and after 14 and 28 days the sealer 20/20 showed the lowest solubility (p<0.05). After 7 days the sealer 20/20 stabilized its solubility. The sealer 40/0 presented the highest values and the 20/20 presented the lowest values of diametral tensile strength and Young’s modulus (p<0.05). The addition of PT to calcium-based root canal sealers provides benefits to the setting time and solubility.

scholarly journals Compressive and diametral tensile strength of glass ionomer cements

2004 ◽  
Vol 12 (4) ◽  
pp. 344-348 ◽  
Author(s):  
Eduardo Bresciani ◽  
Terezinha de Jesus Esteves Barata ◽  
Ticiane Cestari Fagundes ◽  
Akimi Adachi ◽  
Marina Martins Terrin ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Testing Machine ◽  
Glass Ionomer Cement ◽  
Mean Value ◽  
Atraumatic Restorative Treatment ◽  
Glass Ionomer ◽  
Restorative Treatment ◽  
Significant Difference ◽  
The Mean ◽  
Diametral Tensile Strength

The aim of this study was to compare, in different periods of time, the compressive and diametral tensile strength of a traditional high viscous glass ionomer cement: Fuji IX (GC Corporation), with two new Brazilian GIC's: Vitro-Molar (DFL) and Bioglass R (Biodinamica), all indicated for the Atraumatic Restorative Treatment (ART) technique. Fifteen disk specimens (6.0mm diameter x 3.0mm height) for the diametral tensile strength (DTS) test and fifteen cylindrical specimens (6.0mm diameter x 12.0mm height) for the compressive strength (CS) test were made of each GIC. Specimens were stored in deionized water at 37º C and 100% of humidity in a stove until testing. Five specimens of each GIC were submitted to CS and DTS test in each period, namely 1 hour, 24 hours and 7 days. The specimens were tested in a testing machine (Emic) at a crosshead speed of 1.0mm/min for CS and 0.5mm/min for the DTS test until failure occurred. The data were submitted to two-way ANOVA and Tukey tests (alpha=0.05). The mean CS values ranged from 42.03 to 155.47MPa and means DTS from 5.54 to 13.72 MPa, with test periods from 1h to 7 days. The CS and DTS tests showed no statistically significant difference between Fuji IX and Vitro Molar, except for CS test at 1-hour period. Bioglass R had lowest mean value for CS of the cements tested. In DTS test Bioglass R presented no statistically significant differences when compared with all others tested GICs at 1-hour period and Bioglass R presented no difference at 24-hour and 7-day periods when compared to Vitro-Molar. Further studies to investigate other physical properties such as fracture toughness and wear resistance, as well as chemical composition and biocompatibility, are now needed to better understand the properties of these new Brazilian GIC's.

Sign in / Sign up

Export Citation Format

Share Document