scholarly journals INFLUENCE OF CUTTING ON THE PROPERTIES OF CLIPPINGS FROM ELECTRICAL SHEETS

2015 ◽  
Vol 21 (4) ◽  
pp. 302 ◽  
Author(s):  
Emil Spisak ◽  
Janka Majernikova ◽  
Lubos Kascak ◽  
Jan Slota
Keyword(s):  
Magnetic Field ◽  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Magnetic Properties ◽  
Electrical Resistance ◽  
Electric Machines ◽  
Crystallographic Structure ◽  
Atomic Lattice ◽  
Cold Forming ◽  
The Magnetic Field

<p class="AMSmaintext">During cutting, there is a plastic deformation in the cutting area and subsequent hardening of material occurs in this area. The hardening of material in the cutting area causes a change in its mechanical properties, which also has an impact on the physical properties of the material. The hardening manifests as an increase in strength, hardness and yield strength and reduction in the elongation and impact strength. The hardened area increases "watts losses" and reduces the magnetic induction in iron. The electrical resistance increases, which is related with failures in the atomic lattice. The degradation of the electrical conductivity can be explained by the fact that any defect resulting in cold forming causes a dispersion of electron waves. The magnetic properties of iron depend on the distribution of the magnetic field in the crystallographic structure. Violation of the crystallographic structure by forming destroys the magnetic field distribution. The magnetic properties get worse. In the end it causes a reduction in the efficiency of electric machines. The paper analyses the influence of cutting on microhardness in the cutting area.</p>

Magnetosensitive Polymer Composites and Effect of Magnetic Field Directivity on their Properties

2016 ◽  
Vol 251 ◽  
pp. 3-7 ◽  
Author(s):  
Egidijus Dragašius ◽  
Evguenia Korobko ◽  
Zoya Novikava ◽  
Elena Sermyazhko
Keyword(s):  
Magnetic Field ◽  
Mechanical Properties ◽  
Magnetic Properties ◽  
Polymer Composites ◽  
Matrix Material ◽  
Vertical Shear ◽  
Horizontal Shear ◽  
Dispersed Particles ◽  
The Magnetic Field ◽  
Ferromagnetic Particles

Mechanical properties of polymer composite materials, containing ferromagnetic small dispersed particles of carbonyl iron that create structures along force lines of the magnetic field have been investigated. In paper the influence of the polymer matrix material and the orientation of ferromagnetic particles inside it on the properties of polymer composites are considered in the regimes of horizontal shear, vertical shear and periodical (sinusoidal) deformation of the samples. Magnetic properties at the change of magnetic field induction B in the range of 0 to 1 T are determined.

Investigating flexible textile-based coils for wireless charging wearable electronics

2019 ◽  
Vol 50 (3) ◽  
pp. 333-345 ◽  
Author(s):  
Danmei Sun ◽  
Meixuan Chen ◽  
Symon Podilchak ◽  
Apostolos Georgiadis ◽  
Qassim S Abdullahi ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Electrical Conductivity ◽  
Electromagnetic Field ◽  
Electric Field ◽  
Dimensional Stability ◽  
Screen Printing ◽  
Wearable Electronics ◽  
Wireless Charging ◽  
The Magnetic Field ◽  
Screen Printed

Smart and interactive textiles have been attracted great attention in recent years. This research explored three different techniques and processes in developing textile-based conductive coils that are able to embed in a garment layer. Coils made through embroidery and screen printing have good dimensional stability, although the resistance of screen printed coil is too high due to the low conductivity of the print ink. Laser cut coil provided the best electrical conductivity; however, the disadvantage of this method is that it is very difficult to keep the completed coil to the predetermined shape and dimension. The tested results show that an electromagnetic field has been generated between the textile-based conductive coil and an external coil that is directly powered by electricity. The magnetic field and electric field worked simultaneously to complete the wireless charging process.

scholarly journals Hydromagnetic dynamos in rotating spherical fluid shells in dependence on the Prandtl number, density stratification and electromagnetic boundary conditions

2014 ◽  
Vol 44 (4) ◽  
pp. 293-312 ◽  
Author(s):  
Tomáš Šoltis ◽  
Ján Šimkanin
Keyword(s):  
Magnetic Field ◽  
Electrical Conductivity ◽  
Magnetic Fields ◽  
Prandtl Number ◽  
Inner Core ◽  
Polar Regions ◽  
Number Density ◽  
Magnetic Diffusion ◽  
Spherical Fluid ◽  
The Magnetic Field

Abstract We present an investigation of dynamo in a simultaneous dependence on the non-uniform stratification, electrical conductivity of the inner core and the Prandtl number. Computations are performed using the MAG dynamo code. In all the investigated cases, the generated magnetic fields are dipolar. Our results show that the dynamos, especially magnetic field structures, are independent in our investigated cases on the electrical conductivity of the inner core. This is in agreement with results obtained in previous analyses. The influence of non-uniform stratification is for our parameters weak, which is understandable because most of the shell is unstably stratified, and the stably stratified region is only a thin layer near the CMB. The teleconvection is not observed in our study. However, the influence of the Prandtl number is strong. The generated magnetic fields do not become weak in the polar regions because the magnetic field inside the tangent cylinder is always regenerated due to the weak magnetic diffusion.

Study of the Performance of Practical Magneto-Rheological Elastomers

2012 ◽  
Vol 430-432 ◽  
pp. 1979-1983
Author(s):  
Wei Bang Feng ◽  
Xue Yang ◽  
Zhi Qiang Lv
Keyword(s):  
Magnetic Field ◽  
Mechanical Properties ◽  
Mechanical Property ◽  
Magnetic Properties ◽  
External Magnetic Field ◽  
Magnetic Particles ◽  
Poor Performance ◽  
Electrical And Magnetic Properties ◽  
Intelligent Material ◽  
Magneto Rheological

Magneto-rheological elastomer( MR elastomer) is an emerging intelligent material made up of macromolecule polymer and magnetic particles. While a promising wide application it has in the fields of warships vibration controlling for its controllable mechanical, electrical and magnetic properties by external magnetic field, design and application of devices based on it are facing great limitations imposed by its poor performance in mechanical properties and magneto effect. Aiming at developing a practical MR elastomer, a new confecting method was proposed in this paper. Then, following this new method and using a specificly designed solidifying matrix, an amido- polyester MR elastomer was developed with its mechanical property systemically explored.

Martensitic Transformation and Mechanical Properties of Fe-Doped Ni54Mn21Ga25 Alloys

2011 ◽  
Vol 687 ◽  
pp. 500-504
Author(s):  
S. X. Xue ◽  
S.S. Feng ◽  
P. Y. Cai ◽  
Q T Li ◽  
H. B. Wang
Keyword(s):  
Magnetic Field ◽  
Mechanical Properties ◽  
Magnetic Properties ◽  
Martensitic Transformation ◽  
Curie Temperature ◽  
Directional Solidification ◽  
Transformation Temperature ◽  
Room Temperature ◽  
Martensitic Transformation Temperature ◽  
Polycrystalline Alloys

Ni54Mn21-xFexGa25（x=0,1,3,5,7,9）polycrystalline alloys were prepared by the technique of directional solidification and the effect of substituting Fe for Mn on the martensitic transformation and mechanical properties of the alloys was analyzed. It was found that the Curie temperature increased with increasing substitution while the martensitic transformation temperature decreased. The Fe-doped Ni54Mn21Ga25 alloys exhibit excellent magnetic properties at room temperature; the typical Ni54Mn20Fe1Ga25 alloy shows a large magnetic-induced-strain of -1040 ppm at a magnetic field of 4000 Oe.

scholarly journals Field- and Stress-Induced Magnetic Anisotropy in Nanocrystalline Fe-Based and Amorphous Co-Based Alloys

1999 ◽  
Vol 32 (1-4) ◽  
pp. 289-294
Author(s):  
V. A. Lukshina ◽  
N. V. Dmitrieva ◽  
A. P. Potapov
Keyword(s):  
Magnetic Field ◽  
Magnetic Properties ◽  
Amorphous Alloy ◽  
Magnetic Anisotropy ◽  
Thermomechanical Treatment ◽  
Nanocrystalline Alloy ◽  
Complex Effect ◽  
Induced Magnetic Anisotropy ◽  
The Magnetic Field

For nanocrystalline alloy Fe73.5Cu1Nb3Si13.5B9 thermomechanical treatment was carried out simultaneously with nanocrystallizing annealing (1) or after it (2). It was shown that a change in magnetic properties for the case 1 is essentially greater than for the case 2. Complex effect of thermomagnetic and thermomechanical treatments on magnetic properties was studied in the above-mentioned nanocrystalline alloy as well as in the amorphous alloy Fe5Co70.6Si15B9.4., During the annealings both field and stress were aligned with the long side of the specimens. It was shown that the magnetic field, AC or DC, decreases an effect of loading. Moreover, the magnetic field, AC or DC, applied after stress-annealing can destroy the magnetic anisotropy already induced under load.

scholarly journals Tribological Evolution of the Superficial Layer and the Effects of the Magnetic Field to a Non- conventional Treated Steel, During Wear Tests

2018 ◽  
Vol 55 (3) ◽  
pp. 442-446
Author(s):  
Carmen Penelopi Papadatu ◽  
Andrei Victor Sandu ◽  
Marian Bordei ◽  
Ioan Gabriel Sandu ◽  
Sorin Ciortan
Keyword(s):  
Magnetic Field ◽  
Mechanical Properties ◽  
Dry Friction ◽  
Experimental Tests ◽  
Superficial Layer ◽  
Alloyed Steel ◽  
Wear Process ◽  
The Magnetic Field ◽  
Wear Tests ◽  
Made In

The article focuses on the behavior of the non-conventional treated alloyed steel in magnetic field, during the dry wear tests. It is a review of the experimental tests from last years. The thermo-magnetic treatments have been applied before the application of a thermo-chemical treatment in plasma based on diffusion process. The study was made in order to improve the mechanical properties of the alloyed steel during the friction wear. Thermo-magnetic treatment applied before the plasma nitro-carburizing treatment improves the mechanical properties of the material especially in this case, for a steel that has a considerable content of Chromium (1.02%). The behavior was studied using X-Ray diffractometry of the superficial layers during the dry friction of wear process. The wear tests used an Amsler machine, during three hours of wear tests. After each hour of the wear tests the samples have been analyzed. The diffractometric characteristics of the superficial layers obtained after a complex array of thermo-magnetic and thermo-chemical in plasma treatments, the phases distribution, the content of the superficial layers and the behavior of the steel during the wear through dry friction tests, have been considered as criteria.

The stability of viscous flow between rotating cylinders in the presence of a magnetic field

1953 ◽  
Vol 216 (1126) ◽  
pp. 293-309 ◽  
Keyword(s):  
Magnetic Field ◽  
Electrical Conductivity ◽  
Viscous Flow ◽  
Thermal Instability ◽  
Horizontal Layer ◽  
Rotational Stability ◽  
Marginal Stability ◽  
Inhibiting Effect ◽  
The Stability ◽  
The Magnetic Field

In this paper the theory of the stability of viscous flow between two rotating coaxial cylinders which has been developed by Taylor, Jeffreys and Meksyn is extended to the case when the fluid considered is an electrical conductor and a magnetic field along the axis of the cylinders is present. A differential equation of order eight is derived which governs the situation in marginal stability; and a significant set of boundary conditions for the problem is formulated. The case when the two cylinders are rotating in the same direction and the difference ( d ) in their radii is small compared to their mean (R 0 ) is investigated in detail. A variational procedure for solving the underlying characteristic value problem and determining the critical Taylor numbers for the onset of instability is described. As in the case of thermal instability of a horizontal layer of fluid heated below, the effect of the magnetic field is to inhibit the onset of instability, the inhibiting effect being the greater, the greater the strength of the field and the value of the electrical conductivity. In both cases, the inhibiting effect of the magnetic field depends on the strength of the field ( H ), the density ( ρ ) and the coefficients of electrical conductivity ( σ ), kinematic viscosity ( v ) and magnetic permeability ( μ ) through the same non-dimensional combination Q =μ 2 H 2 d 2 σ/ pv ; however, the effect on rotational stability is more pronounced than on thermal instability. A table of the critical Taylor numbers for various values of Q is provided.

Sign in / Sign up

Export Citation Format

Share Document