Some theoretical considerations relating to strain concentration in elastic-plastic bending of beams

1968 ◽  
Vol 3 (4) ◽  
pp. 304-312 ◽  
Author(s):  
M Radomski ◽  
D J White
Keyword(s):  
Strain Hardening ◽  
Numerical Solutions ◽  
Bending Moment ◽  
Rate Of Change ◽  
Plastic Bending ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Rate Of Increase ◽  
Plastic Zones ◽  
Elastic Perfectly Plastic

Theoretical derivations are presented for the relations between maximum deflection and the corresponding maximum strain for some simple beams subject to elastic-plastic bending. Both elastic-perfectly plastic and arbitrary stress-strain relations are considered. Where possible, explicit analytical solutions are given, but where this is not possible numerical solutions are obtained by means of computer programmes. The calculations show that in elastic-perfectly plastic material short plastic zones may develop and cause large strains in the beam even though the deflection corresponding to first yield is not greatly exceeded. On the other hand, strain hardening elongates the plastic zones, so producing a more favourable strain distribution along the length of the beam than would exist without it. The more pronounced the strain-hardening characteristic, i.e. the greater the rate of increase of stress with strain, the less concentrated will be the strains. The mode of loading is important in that the higher the rate of change of bending moment, in the region of ihe maximum bending moment, the more concentrated will be the local strains.

Effects of Torsion on Equivalent Bending Moment for Limit Load and EPFM Circumferential Pipe Flaw Evaluations

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Phuong H. Hoang ◽  
Kunio Hasegawa ◽  
Bostjan Bezensek ◽  
Yinsheng Li
Keyword(s):  
Finite Element ◽  
Pressure Vessel ◽  
Large Strain ◽  
Bending Moment ◽  
Limit Load ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Plastic Materials ◽  
Weighted Factor ◽  
Elastic Perfectly Plastic

The circumferential flaw evaluation procedures in ASME Boiler and Pressure Vessel Code Section XI nonmandatory Appendix C are currently limited to straight pipes under pressure and bending loads without consideration of torsion loading. The Working Group on Pipe Flaw Evaluation of the ASME Boiler and Pressure Vessel Code is developing guidance for considering the effects of torsion by a mean of an equivalent bending moment, which is a square root of sum square combination of bending moment and torsion load with a weighted factor for torsion moment. A torsion weighted factor, Ce, is established in this paper using large strain finite element limit load analysis with elastic perfectly plastic materials. Planar flaws and nonplanar flaws in a 10.75 in. (273 mm) OD pipe are investigated. Additionally, a finite element J-integral calculation is performed for a planar through wall circumferential flaw with elastic plastic materials subjected to bending and torsion load combinations. The proposed Ce factor for planar flaws is intended for use with the ASME B&PV Code Section XI, Appendix C for limit load and Elastic Plastic Fracture Mechanics (EPFM) circumferential planar flaw evaluations.

Dynamic Expansion of a Spherical Cavity in an Elastic, Perfectly Plastic Material

1968 ◽  
Vol 35 (2) ◽  
pp. 372-378 ◽  
Author(s):  
Chi-Hung Mok
Keyword(s):  
Spherical Cavity ◽  
High Speed ◽  
Numerical Solutions ◽  
Plastic Material ◽  
Numerical Technique ◽  
Nonlinear Dependence ◽  
Static Approximation ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic

It is shown that initial and boundary-value problems involving high-speed elastic-plastic deformation with spherical symmetry can be solved using a finite-difference numerical technique. Numerical solutions for the dynamic expansion of a spherical cavity under a constant pressure are presented to demonstrate the nature and capability of the numerical scheme. While the solution for an elastic material agrees closely with the exact one, the solution for an elastic, perfectly plastic material also receives support from Green’s analytic predictions concerning the motion of the elastic-plastic boundary. At large times, the asymptotic solution of the dynamic elastic-plastic problem is different from the quasi-static solution. This result indicates that the concept of quasi-static approximation may not hold in dynamic plasticity. A nonlinear dependence of the plastic solution on the boundary condition is also observed.

The Elastic, Plastic Bending of a Simply Supported Plate

1961 ◽  
Vol 28 (3) ◽  
pp. 395-401 ◽  
Author(s):  
G. Eason
Keyword(s):  
Yield Condition ◽  
Constant Load ◽  
Flow Rule ◽  
Plastic Bending ◽  
Simply Supported ◽  
Elastic Plastic ◽  
Tresca Yield Condition ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic ◽  
Von Mises

In this paper the problem of the elastic, plastic bending of a circular plate which is simply supported at its edge and carries a constant load over a central circular area is considered. The von Mises yield condition and the associated flow rule are assumed and the material of the plate is assumed to be nonhardening, elastic, perfectly plastic, and compressible. Stress fields are obtained in all cases and a velocity field is presented for the case of point loading. Some numerical results are given comparing the results obtained here with those obtained when the Tresca yield condition is assumed.

Numerical Study of Defect Free Elbows Subjected to In-Plane Bending Moment

2011 ◽  
Vol 189-193 ◽  
pp. 1494-1497
Author(s):  
Wang Chen ◽  
Yin Pei Wang ◽  
Pei Ning Li ◽  
Chen Jin ◽  
Xiao Ming Sun
Keyword(s):  
Numerical Study ◽  
Plastic Material ◽  
Three Dimensional ◽  
Bending Moment ◽  
Plastic Behavior ◽  
Piping System ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Bending Radius ◽  
Elastic Perfectly Plastic

Elbow is a type of components widely used in a piping system, and so it is very important to know the plastic carrying capacity of elbow. In this study, the elastic-plastic behavior of elbows with various ratios of t/rm and relative bending radius R/rm were investigated in detail by using of three-dimensional (3D) non-linear finite element (FE) analyses, assuming elastic-perfectly-plastic material behaviour and taking geometric nonlinearity into account. The analyses indicated that elbow exhibited different behavior obviously at the elastic-plastic states subjected to In-Plane opening bending moment and closing bending moment. The closed form equations of elbow involving effect of tangent pipes were established.

Displacements in a Wide Curved Bar Subjected to Pure Elastic-Plastic Bending

1957 ◽  
Vol 24 (3) ◽  
pp. 447-452
Author(s):  
Bernard W. Shaffer ◽  
Raymond N. House
Keyword(s):  
Applied Load ◽  
Bending Moment ◽  
Incompressible Material ◽  
Pure Bending ◽  
Plastic Bending ◽  
Elastic Case ◽  
Elastic Plastic ◽  
Material Thickness ◽  
Perfectly Plastic ◽  
Order Of Magnitude

Abstract Equations have been obtained for the displacements and strains within a wide curved bar made of a perfectly plastic, incompressible material subjected to a pure bending moment which is sufficiently large to cause elastic-plastic stresses. It is found that whenever the applied load is within 95 per cent of the fully plastic bending moment, displacements and strains in the elastic-plastic problem are of the order of magnitude of the corresponding elastic case. It is also found that when the bending moment reaches approximately 65 per cent of the fully plastic bending moment, the change in material thickness reaches a maximum. It decreases to zero when the bar becomes completely plastic.

Improved analysis method for structural members subjected to blast loads considering strain hardening and softening effects

2021 ◽  
pp. 136943322110073
Author(s):  
Liuliang Cui ◽  
Xihong Zhang ◽  
Hong Hao
Keyword(s):  
Strain Hardening ◽  
Direct Shear ◽  
Analysis Method ◽  
Analysis And Design ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Design Charts ◽  
Plastic Hardening ◽  
Elastic Perfectly Plastic ◽  
Hardening And Softening

In analysis and design of structures subjected to blast loading, equivalent Single-Degree-of-Freedom (SDOF) method is commonly recommended in design guides. In this paper, improved analysis method based on SDOF models is proposed. Both flexural and direct shear behaviors of structures subjected to blast load are studied using equivalent SDOF systems. Methods of deriving flexural and direct shear resistance functions are introduced, of which strain hardening and softening effects are considered. To collocate with the improved SDOF models, the improved design charts accounting for strain hardening and softening are developed through systematical analysis of SDOF systems. To demonstrate the effectiveness of the proposed analysis method, a model validation is made through comparing the predictions with laboratory shock tube testing results on reinforced concrete (RC) columns. It is found that compared to the conventional approach with elastic and elastic-perfectly-plastic model, the elastic-plastic-hardening model provides more accurate predictions. Additional non-dimensional design charts considering various levels of elastic-plastic-hardening/softening resistance functions are developed to supplement those available in the design guides with elastic-perfectly-plastic resistance function only, which provide engineers with options to choose more appropriate resistance functions in design analysis.

Combined Viscous and Plastic Deformations in Two-Dimensional Large Strain Finite Element Analysis

1985 ◽  
Vol 107 (1) ◽  
pp. 13-18 ◽  
Author(s):  
B. V. Kiefer ◽  
P. D. Hilton
Keyword(s):  
Finite Element ◽  
Input Parameter ◽  
Time Integration ◽  
Strain Increment ◽  
Total Strain ◽  
Two Dimensional ◽  
Elastic Plastic ◽  
Time Stepping ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic

Capabilities for the analysis of combined viscous and plastic behavior have been added to an existing finite element computer program for two-dimensional elastic-plastic calculations. This program (PAPSTB) has been formulated for elastic-plastic stress and deformation analyses of two-dimensional and axisymmetric structures. It has the ability to model large strains and large deformations of elastic-perfectly plastic, multi-linear hardening, or power-hardening materials. The program is based on incremental plasticity theory with a von Mises yield criterion. Time dependent behavior has been introduced into the PAPSTB program by adding a viscous strain increment to the elastic and plastic strain increment to form the total strain increment. The viscous calculations presently employ a power-law relationship between the viscous strain rate and the effective stress. The finite element code can be easily modified to handle more complex viscous models. The Newmark method for time integration is used, i.e., an input parameter is included which enables the user to vary the time domain approximation between forward (explicit) and backward (implicit) difference. Automatic time stepping is used to provide for stability in the viscous calculations. It is controlled by an input parameter related to the ratio of the current viscous strain increment to the total strain. The viscoplastic capabilities of the PAPSTB program are verified using the axisymmetric problem of an internally pressurized, thick-walled cylinder. The transient viscoplastic case is analyzed to demonstrate that the elastic-perfectly plastic solution is obtained as a steady-state condition is approached. The influence of varying the time integration parameter for transient viscoplastic calculations is demonstrated. In addition, the effects of time step on solution accuracy are investigated by means of the automatic time stepping algorithm in the program. The approach is then applied to a simple forging problem of cylinder upsetting.

An Elastic-Plastic Finite Element Model of Rolling Contact, Part 2: Analysis of Repeated Contacts

1985 ◽  
Vol 52 (1) ◽  
pp. 75-82 ◽  
Author(s):  
V. Bhargava ◽  
G. T. Hahn ◽  
C. A. Rubin
Keyword(s):  
Finite Element ◽  
Shear Strain ◽  
Element Model ◽  
Rolling Contact ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Rolling Contacts ◽  
Elastic Perfectly Plastic ◽  
Multiple Translations ◽  
Contact Part

This paper presents finite element analyses of two-dimensional (plane strain), elastic-plastic, repeated, frictionless rolling contact. The analysis employs the elastic-perfectly plastic, cycle and strain-amplitude-independent material used in the Merwin and Johnson analysis but avoids several assumptions made by these workers. Repeated rolling contacts are simulated by multiple translations of a semielliptical Hertzian pressure distribution. Results at p0/k = 3.5, 4.35, and 5.0 are compared to the Merwin and Johnson prediction. Shakedown is observed at p0/k = 3.5, but the comparisons reveal significant differences in the amount and distribution of residual shear strain and forward flow at p0/k = 4.35 and p0/k = 5.0. The peak incremental, shear strain per cycle for steady state is five times the value calculated by Merwin and Johnson, and the plastic strain cycle is highly nonsymmetric.

A Compressible Elastic, Perfectly Plastic Wedge

1958 ◽  
Vol 25 (2) ◽  
pp. 239-242
Author(s):  
D. R. Bland ◽  
P. M. Naghdi
Keyword(s):  
Plane Strain ◽  
Yield Criterion ◽  
The State ◽  
Hardening Material ◽  
Included Angle ◽  
Elastic Plastic ◽  
Numerical Example ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic

Abstract This paper is concerned with a compressible elastic-plastic wedge of an included angle β < π/2 in the state of plane strain. The solution, deduced for an isotropic nonwork-hardening material, employs Tresca’s yield criterion and the associated flow rules. By means of a numerical example the solution is compared with that of an incompressible elastic-plastic wedge in one case (β = π/4) for various positions of the elastic-plastic boundary.

Stresses and Displacements in an Elastic-Plastic Wedge

1957 ◽  
Vol 24 (1) ◽  
pp. 98-104
Author(s):  
P. M. Naghdi
Keyword(s):  
Plane Strain ◽  
Isotropic Material ◽  
Complete Solution ◽  
Normal Pressure ◽  
Stress Strain ◽  
Included Angle ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Plastic Domain ◽  
Elastic Perfectly Plastic

Abstract An elastic, perfectly plastic wedge of an incompressible isotropic material in the state of plane strain is considered, where the stress-strain relations of Prandtl-Reuss are employed in the plastic domain. For a wedge (with an included angle β) subjected to a uniform normal pressure on one boundary, the complete solution is obtained which is valid in the range 0 < β < π/2; this latter limitation is due to the character of the initial yield which depends on the magnitude of β. Numerical results for stresses and displacements are given in one case (β = π/4) for various positions of the elastic-plastic boundary.

Sign in / Sign up

Export Citation Format

Share Document