Study on temperature-rising rules of self-heating airfield pavement with continuous carbon fiber heating wire

2016 ◽  
pp. 95-99
Author(s):  
Wei Xu ◽  
Chun-Ming Li ◽  
Gui Xu ◽  
Guang-Yuan Li
Keyword(s):  
Carbon Fiber ◽  
Self Heating ◽  
Heating Wire ◽  
Continuous Carbon Fiber

Self-heating 3D printed continuous carbon fiber/epoxy mesh and its application in wind turbine deicing

2020 ◽  
Vol 82 ◽  
pp. 106309 ◽  
Author(s):  
Yueke Ming ◽  
Yugang Duan ◽  
Shaoqiu Zhang ◽  
Yansong Zhu ◽  
Ben Wang
Keyword(s):  
Carbon Fiber ◽  
Wind Turbine ◽  
Self Heating ◽  
Continuous Carbon Fiber ◽  
3D Printed ◽  
Carbon Fiber Epoxy

Effects of high pressure on the crystallization of carbon fiber reinforced polyetheretherketone (CF/PEEK) laminate composites

1990 ◽  
Vol 48 (4) ◽  
pp. 876-877
Author(s):  
Hong-Ming Lin ◽  
C. H. Liu ◽  
R. F. Lee
Keyword(s):  
High Pressure ◽  
Carbon Fiber ◽  
Sample Surface ◽  
High Yield ◽  
Fiber Reinforced ◽  
Laminate Composites ◽  
Peek Composite ◽  
Continuous Carbon Fiber ◽  
Carbon Fiber Reinforced

Polyetheretherketone (PEEK) is a crystallizable thermoplastic used as composite matrix materials in application which requires high yield stress, high toughness, long term high temperature service, and resistance to solvent and radiation. There have been several reports on the crystallization behavior of neat PEEK and of CF/PEEK composite. Other reports discussed the effects of crystallization on the mechanical properties of PEEK and CF/PEEK composites. However, these reports were all concerned with the crystallization or melting processes at or close to atmospheric pressure. Thus, the effects of high pressure on the crystallization of CF/PEEK will be examined in this study.The continuous carbon fiber reinforced PEEK (CF/PEEK) laminate composite with 68 wt.% of fibers was obtained from Imperial Chemical Industry (ICI). For the high pressure experiments, HIP was used to keep these samples under 1000, 1500 or 2000 atm. Then the samples were slowly cooled from 420 °C to 60 °C in the cooling rate about 1 - 2 degree per minute to induce high pressure crystallization. After the high pressure treatment, the samples were scanned in regular DSC to study the crystallinity and the melting temperature. Following the regular polishing, etching, and gold coating of the sample surface, the scanning electron microscope (SEM) was used to image the microstructure of the crystals. Also the samples about 25mmx5mmx3mm were prepared for the 3-point bending tests.

Linear translaminar fracture characterization of additive manufactured continuous carbon fiber reinforced thermoplastic

2021 ◽  
pp. 089270572110214
Author(s):  
Weiller M Lamin ◽  
Flávio LS Bussamra ◽  
Rafael TL Ferreira ◽  
Rita CM Sales ◽  
José E Baldo
Keyword(s):  
Fracture Toughness ◽  
Carbon Fiber ◽  
Fracture Mechanics ◽  
Image Correlation ◽  
Fiber Reinforced ◽  
Fused Filament Fabrication ◽  
Critical Energy Release Rate ◽  
Linear Elastic ◽  
Continuous Carbon Fiber ◽  
Carbon Fiber Reinforced

This work presents the experimental determination of fracture mechanics parameters of composite specimens manufactured by fused filament fabrication (FFF) with continuous carbon fiber reinforced thermoplastic filaments, based on Linear Elastic Fracture Mechanics (LEFM). The critical mode I translaminar fracture toughness (KIc) and the critical energy release rate (GIc) are found for unidirectional and cross-ply laminates. The specimens were submitted to quasi-static tensile testing. Digital Image Correlation (DIC) is used to find the stress field. The stress fields around the crack tip are compared to linear elastic finite element simulations. The results demonstrate the magnitude of fracture toughness is in the same range as for polymers and some metals, depending on lay-up configuration. Besides, fractographic analyses show some typical features as river lines, fiber impression, fiber pulls-out and porosity aspects.

Additive Manufacturing Using Continuous Carbon Fiber

2021 ◽  
Vol 39 (4) ◽  
pp. 314-317
Author(s):  
Yasuhisa Hirata ◽  
Kohei Yamamoto
Keyword(s):  
Additive Manufacturing ◽  
Carbon Fiber ◽  
Continuous Carbon Fiber
Sign in / Sign up

Export Citation Format

Share Document