scholarly journals Analysis of the Known Synergistic Effects of the Exposure to Selected Air Pollutants

2015 ◽  
pp. 255-274
Keyword(s):  
Air Pollutants ◽  
Synergistic Effects

Some Effects of Oxidant Air Pollutants (Ozone and Peroxyacetyl Nitrate) on the Ultrastructure of Leaf Tissues

1972 ◽  
Vol 30 ◽  
pp. 360-361
Author(s):  
William W. Thomson ◽  
Elizabeth S. Swanson
Keyword(s):  
Air Pollutants ◽  
Electron Microscopic Examination ◽  
Peroxyacetyl Nitrate ◽  
Electron Microscopic ◽  
Growth Physiology ◽  
Physiology And Biochemistry ◽  
Entire Plant ◽  
Leaf Tissues ◽  
Gaseous Hydrocarbons ◽  
The Individual

The oxidant air pollutants, ozone and peroxyacetyl nitrate, are produced in the atmosphere through the interaction of light with nitrogen oxides and gaseous hydrocarbons. These oxidants are phytotoxicants and are known to deleteriously affect plant growth, physiology, and biochemistry. In many instances they induce changes which lead to the death of cells, tissues, organs, and frequently the entire plant. The most obvious damage and biochemical changes are generally observed with leaves.Electron microscopic examination of leaves from bean (Phaseolus vulgaris L.) tobacco (Nicotiana tabacum L.) and cotton (Gossipyum hirsutum L.) fumigated for .5 to 2 hours with 0.3 -1 ppm of the individual oxidants revealed that changes in the ultrastructure of the cells occurred in a sequential fashion with time following the fumigation period. Although occasional cells showed severe damage immediately after fumigation, the most obvious change was an enhanced clarity of the cell membranes.

Freeze-dried dispersions for automated SEM analysis of individual submicron airborne particulates

1992 ◽  
Vol 50 (1) ◽  
pp. 408-409
Author(s):  
Karen A. Katrinak ◽  
David W. Brekke ◽  
John P. Hurley
Keyword(s):  
Air Pollutants ◽  
Size Range ◽  
Sem Analysis ◽  
Individual Particle ◽  
Chemical Data ◽  
Particle Analysis ◽  
Bulk Analysis ◽  
Airborne Particulates ◽  
Freeze Dried ◽  
Individual Particle Analysis

Individual-particle analysis is well established as an alternative to bulk analysis of airborne particulates. It yields size and chemical data on a particle-by-particle basis, information that is critical in predicting the behavior of air pollutants. Individual-particle analysis is especially important for particles with diameter < 1 μm, because particles in this size range have a disproportionately large effect on atmospheric visibility and health.

Morphology of High-Performance Rigid-Rod Polymer Fibers and Molecular Composites

1989 ◽  
Vol 47 ◽  
pp. 338-339
Author(s):  
W.W. Adams ◽  
S. J. Krause
Keyword(s):  
Tensile Strength ◽  
High Performance ◽  
Liquid Crystalline ◽  
Molecular Level ◽  
Synergistic Effects ◽  
Tensile Modulus ◽  
Commercial Development ◽  
The Matrix ◽  
Molecular Composites ◽  
Rigid Rod

Rigid-rod polymers such as PBO, poly(paraphenylene benzobisoxazole), Figure 1a, are now in commercial development for use as high-performance fibers and for reinforcement at the molecular level in molecular composites. Spinning of liquid crystalline polyphosphoric acid solutions of PBO, followed by washing, drying, and tension heat treatment produces fibers which have the following properties: density of 1.59 g/cm3; tensile strength of 820 kpsi; tensile modulus of 52 Mpsi; compressive strength of 50 kpsi; they are electrically insulating; they do not absorb moisture; and they are insensitive to radiation, including ultraviolet. Since the chain modulus of PBO is estimated to be 730 GPa, the high stiffness also affords the opportunity to reinforce a flexible coil polymer at the molecular level, in analogy to a chopped fiber reinforced composite. The objectives of the molecular composite concept are to eliminate the thermal expansion coefficient mismatch between the fiber and the matrix, as occurs in conventional composites, to eliminate the interface between the fiber and the matrix, and, hopefully, to obtain synergistic effects from the exceptional stiffness of the rigid-rod molecule. These expectations have been confirmed in the case of blending rigid-rod PBZT, poly(paraphenylene benzobisthiazole), Figure 1b, with stiff-chain ABPBI, poly 2,5(6) benzimidazole, Fig. 1c A film with 30% PBZT/70% ABPBI had tensile strength 190 kpsi and tensile modulus of 13 Mpsi when solution spun from a 3% methane sulfonic acid solution into a film. The modulus, as predicted by rule of mixtures, for a film with this composition and with planar isotropic orientation, should be 16 Mpsi. The experimental value is 80% of the theoretical value indicating that the concept of a molecular composite is valid.

Sign in / Sign up

Export Citation Format

Share Document