Microstructure and shear strength of low-silver SAC/Cu solder joints during the thermal cycle

2015 ◽  
pp. 373-376
Author(s):  
H Wang ◽  
G Gan ◽  
D Yang ◽  
G Meng ◽  
H Luo
Keyword(s):  
Shear Strength ◽  
Thermal Cycle ◽  
Solder Joints

scholarly journals The Interface Microstructure and Shear Strength of Sn2.5Ag0.7Cu0.1RExNi/Cu Solder Joints under Thermal-Cycle Loading

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 518 ◽  
Author(s):  
Congcong Cao ◽  
Keke Zhang ◽  
Baojin Shi ◽  
Huigai Wang ◽  
Di Zhao ◽  
...  
Keyword(s):  
Shear Strength ◽  
Fracture Mechanism ◽  
Thermal Cycle ◽  
Solder Joints ◽  
Joint Interface ◽  
Interface Microstructure ◽  
Average Thickness ◽  
Thermal Cycles ◽  
Initial State ◽  
Cycle Loading

The interface microstructure and shear strength of Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints under thermal-cycle loading were investigated with scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and physical and chemical tests. The results show that an intermetallic compound (IMC) layer of Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints evolved gradually from the scalloped into larger wavy forms with increasing number of thermal cycles. The roughness and average thickness of IMC increased with thermal-cycle loading. However, at longer thermal-cycle loading, the shear strength of the joints was reduced by about 40%. The fracture pathway of solder joints was initiated in the solder seam with ductile fracture mechanism and propagated to the solder seam/IMC layer with ductile-brittle mixed-type fracture mechanism, when the number of thermal cycles increased from 100 to 500 cycles. By adding 0.05 wt.% Ni, the growth of the joint interface IMC could be controlled, and the roughness and average thickness of the interfacial IMC layer reduced. As a result, the shear strength of joints is higher than those without Ni. When compared to joint without Ni, the roughness and average thickness of 0.05 wt.% Ni solder joint interface IMC layer reached the minimum after 500 thermal cycles. The shear strength of that joint was reduced to a minimum of 36.4% of the initial state, to a value of 18.2 MPa.

scholarly journals Microstructure and shear properties of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints under thermal cycling

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jianguo Cui ◽  
Keke Zhang ◽  
Di Zhao ◽  
Yibo Pan
Keyword(s):  
Shear Strength ◽  
Thermal Cycling ◽  
Solder Joints ◽  
High Reliability ◽  
Sharp Decrease ◽  
Thermal Shock Test ◽  
Shear Properties ◽  
Equivalent Time ◽  
Ultrasonic Assisted ◽  
Reliability Of Solder Joints

AbstractThrough ultrasonic wave assisted Sn2.5Ag0.7Cu0.1RExNi/Cu (x = 0, 0.05, 0.1) soldering test and − 40 to 125 °C thermal shock test, the microstructure and shear properties of Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints under thermal cycling were studied by the SEM, EDS and XRD. The results show that the Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints with high quality and high reliability can be obtained by ultrasonic assistance. When the ultrasonic vibration power is 88 W, the ultrasonic-assisted Sn2.5Ag0.7Cu0.1RE0.05Ni/Cu solder joints exhibits the optimized performance. During the thermal cycling process, the shear strength of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints had a linear relationship with the thickness of interfacial intermetallic compound (IMC). Under the thermal cycling, the interfacial IMC layer of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints consisted of (Cu,Ni)6Sn5 and Cu3Sn. The thickness of interfacial IMC of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints was linearly related to the square root of equivalent time. The growth of interfacial IMC of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints had an incubation period, and the growth of IMC was slow within 300 cycles. And after 300 cycles, the IMC grew rapidly, the granular IMC began to merge, and the thickness and roughness of IMC increased obviously, which led to a sharp decrease in the shear strength of the solder joints. The 0.05 wt% Ni could inhibit the excessive growth of IMC, improve the shear strength of solder joints and improve the reliability of solder joints. The fracture mechanism of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints changed from the ductile–brittle mixed fracture in the solder/IMC transition zone to the brittle fracture in the interfacial IMC.

Effect of intermetallic compound layer thickness on the shear strength of 1206 chip resistor solder joint

2015 ◽  
Vol 27 (1) ◽  
pp. 52-58 ◽  
Author(s):  
Peter K. Bernasko ◽  
Sabuj Mallik ◽  
G. Takyi
Keyword(s):  
Shear Strength ◽  
Intermetallic Compound ◽  
Solder Joint ◽  
Layer Thickness ◽  
Solder Joints ◽  
Ageing Time ◽  
Circuit Board ◽  
Intermetallic Compound Layer ◽  
Content Type ◽  
Surface Mount

Purpose – The purpose of this paper is to study the effect of intermetallic compound (IMC) layer thickness on the shear strength of surface-mount component 1206 chip resistor solder joints. Design/methodology/approach – To evaluate the shear strength and IMC thickness of the 1206 chip resistor solder joints, the test vehicles were conventionally reflowed for 480 seconds at a peak temperature of 240°C at different isothermal ageing times of 100, 200 and 300 hours. A cross-sectional study was conducted on the reflowed and aged 1206 chip resistor solder joints. The shear strength of the solder joints aged at 100, 200 and 300 hours was measured using a shear tester (Dage-4000PXY bond tester). Findings – It was found that the growth of IMC layer thickness increases as the ageing time increases at a constant temperature of 175°C, which resulted in a reduction of solder joint strength due to its brittle nature. It was also found that the shear strength of the reflowed 1206 chip resistor solder joint was higher than the aged joints. Moreover, it was revealed that the shear strength of the 1206 resistor solder joints aged at 100, 200 and 300 hours was influenced by the ageing reaction times. The results also indicate that an increase in ageing time and temperature does not have much influence on the formation and growth of Kirkendall voids. Research limitations/implications – A proper correlation between shear strength and fracture mode is required. Practical implications – The IMC thickness can be used to predict the shear strength of the component/printed circuit board pad solder joint. Originality/value – The shear strength of the 1206 chip resistor solder joint is a function of ageing time and temperature (°C). Therefore, it is vital to consider the shear strength of the surface-mount chip component in high-temperature electronics.

Microstructure evolution and microimpact performance of Sn–Ag–Cu solder joints under thermal cycle test

2010 ◽  
Vol 25 (7) ◽  
pp. 1312-1320 ◽  
Author(s):  
Y.L. Huang ◽  
K.L. Lin ◽  
D.S. Liu
Keyword(s):  
Fracture Energy ◽  
Microstructure Evolution ◽  
Thermal Cycle ◽  
Fracture Behavior ◽  
Solder Ball ◽  
Solder Joints ◽  
Whisker Formation ◽  
Structural Variations ◽  
Before And After ◽  
Ball Joints

The microstructure and microimpact performance of Sn1Ag0.1Cu0.02Ni0.05In (SAC101NiIn)/AuNi/Cu solder ball joints were investigated after a thermal cycle test (TCT). The joints show complete bulk fracture behavior before TCT. Moreover, TCT facilitated interfacial fracture behavior with lower fracture energy. The intermetallic compounds (IMCs) formed in the solder joints before and after TCT were investigated. TCT induces a variety of structural variations in the solder joints, including slipping bands, whisker formation, the squeezing of the IMC layer, the formation of cavities, the rotation and pop-up of grain, and the deformation and rotation of the entire joint. The variations in fracture behavior induced by TCT are correlated with the structural variations in the solder joints.

Thermal cycle effects on laminated composite plates containing voids

2018 ◽  
Vol 53 (4) ◽  
pp. 489-501 ◽  
Author(s):  
Shambhu K Gupta ◽  
Mehdi Hojjati
Keyword(s):  
Shear Strength ◽  
Thermal Cycle ◽  
Composite Structures ◽  
Laminated Composite ◽  
Composite Plates ◽  
Interlaminar Shear Strength ◽  
Void Content ◽  
Manufacturing Method ◽  
Polished Cross Section ◽  
Interlaminar Shear

Composite structures are often cured in an autoclave to acquire the required space grade quality. Now the industry is focusing on the out of autoclave manufacturing method which leads to more voids inside laminate with respect to those manufactured in the autoclave. In the present work, the influence of voids on microcrack formation under thermal cycling and environmental conditions was analyzed. Thermal cycle experiments were performed using liquid nitrogen and oven, followed by microscopic observation of the polished cross-section of the 90° layered plies. Cracks were monitored, counted, and measured with respect to void and void free areas. Void content was characterized using microscopic and ImageJ software was used. It was observed that the microcracks will be formed both around the voids and in void free areas. As the number of thermal cycle increases, the number of microcrack around the voids increases much faster than compared to the void free areas. Also it was observed that most of microcracks were propagated in the transverse direction. Interlaminar shear strength was measured. Results indicate that interlaminar shear strength reduces as the number of cycle rises due to the increase in the microcrack density. Finite element method was used to simulate the process. The micro, meso, and macro model were created with respect to original samples voids and positions to calculate the stress distribution and its concentration. Good agreement between experiment and simulation was observed.

scholarly journals Shear Strength Degradation Modeling of Lead-Free Solder Joints at Different Isothermal Aging Conditions

2021 ◽  
Vol 18 (3) ◽  
pp. 137-144
Author(s):  
Dania Bani Hani ◽  
Raed Al Athamneh ◽  
Mohammed Aljarrah ◽  
Sa’d Hamasha
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Printed Circuit Board ◽  
Solder Joints ◽  
Constant Strain Rate ◽  
Circuit Board ◽  
Sac305 Solder ◽  
Aging Conditions ◽  
Osp Surface Finish ◽  
Shear Strength Degradation

Abstract SAC-based alloys are one of the most common solder materials that are utilized to provide mechanical support and electrical connection between electronic components and the printed circuit board. Enhancing the mechanical properties of solder joints can improve the life of the components. One of the mechanical properties that define the solder joint structure integrity is the shear strength. The main objective of this study is to assess the shear strength behavior of SAC305 solder joints under different aging conditions. Instron 5948 Micromechanical Tester with a customized fixture is used to perform accelerated shear tests on individual solder joints. The shear strength of SAC305 solder joints with organic solderability preservative (OSP) surface finish is investigated at constant strain rate under different aging times (2, 10, 100, and 1,000 h) and different aging temperatures (50, 100, and 150°C). The nonaged solder joints are examined as well for comparison purposes. Analysis of variance (ANOVA) is accomplished to identify the contribution of each parameter on the shear strength. A general empirical model is developed to estimate the shear strength as a function of aging conditions using the Arrhenius term. Microstructure analysis is performed at different aging conditions using scanning electron microscope (SEM). The results revealed a significant reduction in the shear strength when the aging level is increased. An increase in the precipitates coarsening and intermetallic compound (IMC) layer thickness are observed with increased aging time and temperature.

Sign in / Sign up

Export Citation Format

Share Document