Superplasticity and Superplastic Forming

2007 ◽  
pp. 14-1-14-35
Author(s):  
Indrajit Charit ◽  
Rajiv Mishra
Keyword(s):  
Superplastic Forming

A very rapid in situ Kikuchi technique to determine relative crystal misorientation

1988 ◽  
Vol 46 ◽  
pp. 830-831
Author(s):  
J. I. Bennetch
Keyword(s):  
Electron Beam ◽  
Analytical Techniques ◽  
Superplastic Forming ◽  
The Other ◽  
Kikuchi Pattern ◽  
Kikuchi Line ◽  
Line Analysis

In a recent study of the superplastic forming (SPF) behavior of certain Al-Li-X alloys, the relative misorientation between adjacent (sub)grains proved to be an important parameter. It is well established that the most accurate way to determine misorientation across boundaries is by Kikuchi line analysis. However, the SPF study required the characterization of a large number of (sub)grains in each sample to be statistically meaningful, a very time-consuming task even for comparatively rapid Kikuchi analytical techniques.In order to circumvent this problem, an alternate, even more rapid in-situ Kikuchi technique was devised, eliminating the need for the developing of negatives and any subsequent measurements on photographic plates. All that is required is a double tilt low backlash goniometer capable of tilting ± 45° in one axis and ± 30° in the other axis. The procedure is as follows. While viewing the microscope screen, one merely tilts the specimen until a standard recognizable reference Kikuchi pattern is centered, making sure, at the same time, that the focused electron beam remains on the (sub)grain in question.

“Cavity” formation in superplastically deformed aluminium alloys

1990 ◽  
Vol 48 (4) ◽  
pp. 958-959
Author(s):  
A. Cziráki ◽  
E. Ková-csetényi ◽  
T. Torma ◽  
T. Turmezey
Keyword(s):  
Grain Boundaries ◽  
Aluminium Alloys ◽  
Superplastic Deformation ◽  
Volume Fraction ◽  
Superplastic Forming ◽  
Polished Surface ◽  
Cavity Formation ◽  
Stress Concentrations ◽  
Electron Microscopic ◽  
Commercial Aluminium

It is known that the formation of cavities during superplastic deformation can be correlated with the development of stress concentrations at irregularities along grain boundaries such as particles, ledges and triple points. In commercial aluminium alloys Al-Fe-Si particles or other coarse constituents may play an important role in cavity formation.Cavity formation during superplastic deformation was studied by optical metallography and transmission scanning electron microscopic investigations on Al-Mg-Si and Al-Mg-Mn alloys. The structure of particles was characterized by selected area diffraction and X-ray micro analysis. The volume fraction of “voids” was determined on mechanically polished surface.It was found by electron microscopy that strongly deformed regions are formed during superplastic forming at grain boundaries and around coarse particles.According to electron diffraction measurements these areas consist of small micro crystallized regions. See Fig.l.Comparing the volume fraction and morphology of cavities found by optical microscopy a good correlation was established between that of micro crystalline regions.

Research on Quick Superplastic Forming for Aluminium Alloy Sheet

2012 ◽  
Vol 735 ◽  
pp. 301-306 ◽  
Author(s):  
Hai Jian Liang ◽  
Xiao Wei Wu ◽  
Yong Wang ◽  
Quan Lin Jin ◽  
Zhao Li Ma ◽  
...  
Keyword(s):  
Mass Production ◽  
Simulation Experiment ◽  
Hot Stamping ◽  
Superplastic Forming ◽  
Alloy Sheet ◽  
High Rate ◽  
Hot Forming ◽  
Forming Technology ◽  
Complex Process ◽  
Better Than

This article describes the high rate superplastic forming. The high rate superplastic forming technology is a new complex process,which integrates hot stamping and superplastic forming .It has feature of rapidity of the hot stamping and character of excellent formability of the superplastic forming.We obtained the best proportion of the hot forming and the superplastic forming through simulation experiment, and formed a car’s abonnet by applying the proportion.Compared with the high rate superplastic forming,the forming quality is better than that of hot forming. and the forming time is less than that of superplastic forming. Result shows that ,the high rate superplastic forming technology can meet the requirements for mass production.

The Measurement of Friction for Superplastic Forming of Ti-6Al-4V

2004 ◽  
Vol 447-448 ◽  
pp. 111-116 ◽  
Author(s):  
R.B. Kelly ◽  
Sean B. Leen ◽  
I.R. Pashby ◽  
Andrew R. Kennedy
Keyword(s):  
Superplastic Forming

Study on Cavity Growth in Uniaxial Tension of ZK60 Magnesium Alloy

2007 ◽  
Vol 353-358 ◽  
pp. 687-690
Author(s):  
Yan Dong Yu ◽  
De Liang Yin ◽  
Bao You Zhang
Keyword(s):  
Volume Fraction ◽  
Cavity Growth ◽  
Experimental Studies ◽  
Superplastic Forming ◽  
Cavity Radius ◽  
Analysis Software ◽  
Mixed Characteristic ◽  
Substantial Growth ◽  
Zk60 Magnesium Alloy ◽  
Electronic Microscope

Cavity growth is a typical microstructure feature in superplastic forming (SPF) of materials. Substantial growth and interlink of cavities in superplastic deformation usually lead to reduction in elongation, even to failure. Consequently, it is necessary to investigate the mechanism and model of cavity growth. In this paper, experimental studies on cavity growth were carried out by means of superplastic tension of ZK60 magnesium alloys. Scanning electronic microscope (SEM) was employed for observation of fractography. Experimental cavity radius and volume fraction were determined by optical microscopy and corresponding picture-based analysis software. It is found that, the fractured surfaces after a superplastic elongation have a mixed characteristic of intergranular cavities and dimples. Further, the cavity growth is identified to follow a exponentially increasing mode.

Sign in / Sign up

Export Citation Format

Share Document