Analytical solution for direct current electric potential in an anisotropic half‐space with a vertical contact

1997 ◽  
Author(s):  
Ping Li ◽  
Norman F. Uren
Keyword(s):  
Analytical Solution ◽  
Half Space ◽  
Direct Current ◽  
Electric Potential ◽  
Vertical Contact

QUADRIPOLE‐QUADRIPOLE ARRAYS FOR DIRECT CURRENT RESISTIVITY MEASUREMENTS—MODEL STUDIES

Geophysics ◽  
1976 ◽  
Vol 41 (1) ◽  
pp. 79-95 ◽  
Author(s):  
Dariu Doicin
Keyword(s):  
Half Space ◽  
Electric Fields ◽  
Direct Current ◽  
Apparent Resistivity ◽  
Cross Product ◽  
Resistivity Measurements ◽  
Model Studies ◽  
True Resistivity ◽  
Vertical Contact ◽  
Source Dipole

For a quadripole‐quadripole array, in which current is sequentially injected into the ground by two perpendicular dipoles, an apparent resistivity can be defined in terms of the vectorial cross product of the two electric fields measured at the receiver site. Transform equations are derived (for horizontally layered media) which relate this apparent resistivity to the apparent resistivities obtained with conventional dipole‐dipole and Schlumberger arrangements. To evaluate the method, two mathematical models are used. The first model is a half‐space with an “alpha conductivity center,” and the second model is a half‐space with a vertical contact. For an idealized quadripole‐quadripole array, simple expressions are found for the apparent resistivity, which is shown to be independent of the orientation of the current quadripole. Theoretical anomalies calculated for the quadripole‐quadripole array are compared with those obtained for a dipole‐quadripole array. It is shown that whereas the apparent resistivity map for the dipole‐quadripole array varies greatly with the azimuth of the source dipole, the results obtained with the quadripole‐quadripole array consistently display a remarkable resemblance to the assumed distribution of true resistivity. This is especially true when the current quadripole is placed at a large distance from the surveyed area.

Determination of Crack-Initiation in Fracture Toughness Testing Using an Experimental Key-Curve Methodology

2021 ◽  
Author(s):  
S. Pothana ◽  
G. Wilkowski ◽  
S. Kalyanam ◽  
J. K. Hong ◽  
C. J. Sallaberry
Keyword(s):  
Fracture Toughness ◽  
Crack Initiation ◽  
Crack Growth ◽  
Power Law ◽  
Direct Current ◽  
Electric Potential ◽  
Crack Mouth Opening Displacement ◽  
Ductile Tearing ◽  
Curve Method ◽  
Unloading Compliance

Abstract A new approach was implemented to confirm the start of ductile tearing relative to assessments by other methods such as direct-current Electric Potential (d-c EP) method in coupon specimens. This approach was developed on the Key-Curve methodology by Ernst/Joyce and is similar to the ASTM E-1820 Load Normalization procedure used to determine J-R curves directly from load versus Load-Line Displacement (LLD) record of the test specimen. It is consistent with Deformation Plasticity relationships for fully plastic behavior. Using this Experimental Key-Curve method, crack initiation can be determined directly from load versus LLD data or load versus Crack-Mouth Opening Displacement (CMOD) obtained from a fracture test without the need for additional instrumentation required for crack initiation detection. It is based on the fact that plastic deformation of homogeneous metals at the crack tip follows a power-law function until the crack tearing initiates. Crack tearing initiation is determined at the point where the power-law fit to the load versus plastic part of CMOD or LLD curve deviates from the total experimental load versus plastic-CMOD or LLD curve. The procedure for fitting of the data requires some care to be exercised such that the fitted data is beyond the elastic region and early small-scale plastic region of the Load-CMOD or Load-LLD curve but include data before crack initiation. An iterative regression analysis was done to achieve this, which is shown in this paper. The iterative fitting in this region typically results with a coefficient of determination (R2) values that are greater than 0.990. This method can be either used in conjunction with other methods such as direct-current Electric Potential (d-c EP) or unloading-compliance methods as a secondary (or primary) confirmation of crack tearing initiation (and even for crack growth); or can be used alone when other methods cannot be used. Furthermore, when using instrumentation methods for determining crack-initiation such as d-c EP method in a fracture toughness test, it is good to have a secondary confirmation of the initiation point in case of instrumentation malfunction or high signal to noise ratio in the measured d-c EP signals. In addition, the Experimental Key-Curve procedure provides relatively smooth data for the fitting procedure, while unloading-compliance data when used to get small crack growth values frequently has significant variability, which is part of the reason that JIC by ASTM E1820 is determined using an offset with some growth past the very start of ductile tearing. In this work, the Experimental Key-Curve method had been successfully used to determine crack tearing initiation and demonstrate the applicability for different fracture toughness specimen geometries such as SEN(T), and C(T) specimens. In all the cases analyzed, the Experimental Key-Curve method gave consistent results that were in good agreement with other crack tearing initiation measuring method such as d-c EP but seemed to result in less scatter.

Bleustein-Gulyaev Waves in an Inhomogeneous Layered Piezoelectric Half-Space

2006 ◽  
Vol 306-308 ◽  
pp. 1223-1228
Author(s):  
Fei Peng ◽  
Hua Rui Liu
Keyword(s):  
Fourier Transform ◽  
Phase Velocity ◽  
Half Space ◽  
Electric Potential ◽  
Piezoelectric Layer ◽  
Field Equations ◽  
Transform Method ◽  
Coupled Field ◽  
Coupled Field Equations ◽  
The Fourier Transform

The propagation of Bleustein-Gulyaev (BG) waves in an inhomogeneous layered piezoelectric half-space is investigated in this paper. Application of the Fourier transform method and by solving the electromechanically coupled field equations, solutions to the mechanical displacement and electric potential are obtained for the piezoelectric layer and substrate, respectively. The phase velocity equations for BG waves are obtained for the surface electrically shorted case. When the layer and the substrate are homogenous, the dispersion equations are in agreement with the corresponding results. Numerical calculations are performed for the case that the layer and the substrate are identical LiNbO3 except that they are polarized in opposite directions. Effects of the inhomogeneities induced by either the layer or substrate are discussed in detail.

Sign in / Sign up

Export Citation Format

Share Document