scholarly journals MISR Calibration and Implications for Low-Light-Level Aerosol Retrieval over Dark Water

2005 ◽  
Vol 62 (4) ◽  
pp. 1032-1052 ◽  
Author(s):  
Ralph Kahn ◽  
Wen-Hao Li ◽  
John V. Martonchik ◽  
Carol J. Bruegge ◽  
David J. Diner ◽  
...  
Keyword(s):  
Optical Thickness ◽  
Near Infrared ◽  
Light Level ◽  
Single Scattering ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Aerosol Layer ◽  
Radiometric Calibration ◽  
Low Light ◽  
Vicarious Calibration

Abstract Studying aerosols over ocean is one goal of the Multiangle Imaging Spectroradiometer (MISR) and other spaceborne imaging systems. But top-of-atmosphere equivalent reflectance typically falls in the range of 0.03 to 0.12 at midvisible wavelengths and can be below 0.01 in the near-infrared, when an optically thin aerosol layer is viewed over a dark ocean surface. Special attention must be given to radiometric calibration if aerosol optical thickness, and any information about particle microphysical properties, are to be reliably retrieved from such observations. MISR low-light-level vicarious calibration is performed in the vicinity of remote islands hosting Aerosol Robotic Network (AERONET) sun- and sky-scanning radiometers, under low aerosol loading, low wind speed, relatively cloud free conditions. MISR equivalent reflectance is compared with values calculated from a radiative transfer model constrained by coincident, AERONET-retrieved aerosol spectral optical thickness, size distribution, and single scattering albedo, along with in situ wind measurements. Where the nadir view is not in sun glint, MISR equivalent reflectance is also compared with Moderate Resolution Imaging Spectroradiometer (MODIS) reflectance. The authors push the limits of the vicarious calibration method’s accuracy, aiming to assess absolute, camera-to-camera, and band-to-band radiometry. Patterns repeated over many well-constrained cases lend confidence to the results, at a few percent accuracy, as do additional vicarious calibration tests performed with multiplatform observations taken during the Chesapeake Lighthouse and Aircraft Measurements for Satellites (CLAMS) campaign. Conclusions are strongest in the red and green bands, but are too uncertain to accept for the near-infrared. MISR nadir-view and MODIS low-light-level absolute reflectances differ by about 4% in the blue and green bands, with MISR reporting higher values. In the red, MISR agrees with MODIS band 14 to better than 2%, whereas MODIS band 1 is significantly lower. Compared to the AERONET-constrained model, the MISR aft-viewing cameras report reflectances too high by several percent in the blue, green, and possibly the red. Better agreement is found in the nadir- and the forward-viewing cameras, especially in the blue and green. When implemented on a trial basis, calibration adjustments indicated by this work remove 40% of a 0.05 bias in retrieved midvisible aerosol optical depth over dark water scenes, produced by the early postlaunch MISR algorithm. A band-to-band correction has already been made to the MISR products, and the remaining calibration adjustments, totaling no more than a few percent, are planned.

Consistent retrieval of cloud/aerosol single scattering properties and surface reflectance

2021 ◽  
Author(s):  
Marta Luffarelli ◽  
Yves Govaerts
Keyword(s):  
Radiative Transfer ◽  
Optical Thickness ◽  
Solution Space ◽  
Single Scattering ◽  
Aerosol Optical Thickness ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Surface Reflectance ◽  
Earth System ◽  
System Components

<p>The CISAR (Combined Inversion of Surface and AeRosols) algorithm is exploited in the framework of the ESA Aerosol Climate Change Initiatiave (CCI) project, aiming at providing a set of atmospheric (cloud and aerosol) and surface reflectance products derived from S3A/SLSTR observations using the same radiative transfer physics and assumptions. CISAR is an advance algorithm developed by Rayference originally designed for the retrieval of aerosol single scattering properties and surface reflectance from both geostationary and polar orbiting satellite observations.  It is based on the inversion of a fast radiative transfer model (FASTRE). The retrieval mechanism allows a continuous variation of the aerosol and cloud single scattering properties in the solution space.</p><p> </p><p>Traditionally, different approaches are exploited to retrieve the different Earth system components, which could lead to inconsistent data sets. The simultaneous retrieval of different atmospheric and surface variables over any type of surface (including bright surfaces and water bodies) with the same forward model and inversion scheme ensures the consistency among the retrieved Earth system components. Additionally, pixels located in the transition zone between pure clouds and pure aerosols are often discarded from both cloud and aerosol algorithms. This “twilight zone” can cover up to 30% of the globe. A consistent retrieval of both cloud and aerosol single scattering properties with the same algorithm could help filling this gap.</p><p> </p><p>The CISAR algorithm aims at overcoming the need of an external cloud mask, discriminating internally between aerosol and cloud properties. This approach helps reducing the overestimation of aerosol optical thickness in cloud contaminated pixels. The surface reflectance product is delivered both for cloud-free and cloudy observations.  </p><p> </p><p>Global maps obtained from the processing of S3A/SLSTR observations will be shown. The SLSTR/CISAR products over events such as, for instance, the Australian fire in the last months of 2019, will be discussed in terms of aerosol optical thickness, aerosol-cloud discrimination and fine/coarse mode fraction.</p>

scholarly journals On the improvement of NO<sub>2</sub> satellite retrievals – aerosol impact on the airmass factors

2009 ◽  
Vol 2 (6) ◽  
pp. 3221-3264
Author(s):  
J. Leitão ◽  
A. Richter ◽  
M. Vrekoussis ◽  
A. Kokhanovsky ◽  
Q. J. Zhang ◽  
...  
Keyword(s):  
Optical Depth ◽  
Accurate Determination ◽  
Single Scattering ◽  
Sensitivity Study ◽  
Trace Gas ◽  
Radiative Transfer Model ◽  
Satellite Measurement ◽  
Transfer Model ◽  
Aerosol Layer ◽  
The Impact

Abstract. The accurate determination of nitrogen dioxide (NO2) tropospheric vertical columns from satellite measurements depends, partly, on the airmass factor (AMF) used. A sensitivity study was performed with the radiative transfer model SCIATRAN to better understand the impact of aerosols in the calculation of NO2 AMFs. This influence was studied by varying the NO2 and aerosol vertical distributions, as well as physical and optical properties of the particles. The key factors for these calculations were identified as the relation between trace gas and aerosol vertical profiles, the optical depth of the aerosol layer, and single scattering albedo. Overall it was found that aerosol mixed with the trace gas increases the measurements' sensitivity. The largest change, a factor of ~2 relative to the situation without aerosols, was found when a low layer of aerosol (600 m) was combined with a homogenous NO2 layer of 1.0 km. A layer of aerosol above the NO2 will usually reduce the sensitivity of the satellite measurement, a situation found mostly for runs with discrete elevated aerosol layers representative for long-range transport of aerosols that can generate a decrease of the AMF values of up to 70%. The use of measured aerosol profiles and modelled NO2 resulted, generally, in a much smaller changes of AMF relative to the pure Rayleigh case. Exceptions are some events of elevated layers with high aerosol optical depth that lead to a strong decrease of the AMF values. These results highlight the importance of aerosols in the retrieval of tropospheric NO2 columns from space and indicate the need for detailed information on aerosol properties and vertical distribution.

scholarly journals Error sources in the retrieval of aerosol information over bright surfaces from satellite measurements in the oxygen A-band

2017 ◽  
Author(s):  
Swadhin Nanda ◽  
Martin de Graaf ◽  
Maarten Sneep ◽  
Johan F. de Haan ◽  
Piet Stammes ◽  
...  
Keyword(s):  
Optical Thickness ◽  
Surface Albedo ◽  
High Surface ◽  
Aerosol Optical Thickness ◽  
Radiative Transfer Model ◽  
Retrieval Algorithm ◽  
Transfer Model ◽  
Aerosol Layer ◽  
Critical Surface ◽  
Layer Height

Abstract. Retrieving aerosol optical thickness and aerosol layer height over a bright surface from measured top of atmosphere reflectance spectrum in the oxygen A-band is known to be challenging, often resulting in large errors. In certain atmospheric conditions and viewing geometries, a loss of sensitivity to aerosol optical thickness has been reported in literature. This loss of sensitivity has been attributed to a phenomenon known as critical surface albedo regime, which is a range of surface albedos for which the top of atmosphere reflectance has minimal sensitivity to aerosol optical thickness. This paper extends the concept of critical surface albedo for aerosol layer height retrievals in the oxygen A-band, and discusses its implications. The underlying physics are introduced by analysing top of atmosphere reflectance spectra obtained using a radiative transfer model. Furthermore, error analysis of the aerosol layer height retrieval algorithm are conducted over dark and bright surfaces to show the dependency on surface reflectance. The analysis shows that the information on aerosol layer height from atmospheric path contribution and the surface contribution to the top of atmosphere are opposite in sign – an increase in surface brightness results in a decrease in information content. In the case of aerosol optical thickness, these contributions are anti-correlated, leading to large retrieval errors in high surface albedo regimes. The consequence of this anti-correlation is demonstrated with measured spectra in the oxygen A-band from GOME-2A instrument on board the Metop-A satellite over the 2010 Russian wildfires incident.

scholarly journals On the improvement of NO<sub>2</sub> satellite retrievals – aerosol impact on the airmass factors

2010 ◽  
Vol 3 (2) ◽  
pp. 475-493 ◽  
Author(s):  
J. Leitão ◽  
A. Richter ◽  
M. Vrekoussis ◽  
A. Kokhanovsky ◽  
Q. J. Zhang ◽  
...  
Keyword(s):  
Optical Depth ◽  
Accurate Determination ◽  
Single Scattering ◽  
Sensitivity Study ◽  
Trace Gas ◽  
Radiative Transfer Model ◽  
Satellite Measurement ◽  
Transfer Model ◽  
Aerosol Layer ◽  
The Impact

Abstract. The accurate determination of nitrogen dioxide (NO2) tropospheric vertical columns from satellite measurements depends strongly on the airmass factor (AMF) used. A sensitivity study was performed with the radiative transfer model SCIATRAN to better understand the impact of aerosols on the calculation of NO2 AMFs. This influence was studied by varying the NO2 and aerosol vertical distributions, as well as physical and optical properties of the particles. In terms of aerosol definitions, the key factors for these calculations were identified as the relation between trace gas and aerosol vertical profiles, the optical depth of the aerosol layer, and single scattering albedo. In addition, surface albedo also has a large impact on the calculations. Overall it was found that particles mixed with the trace gas increases the measurements' sensitivity, but only when the aerosol is not very absorbing. The largest change, a factor of ~2 relative to the situation without aerosols, was found when a low layer of aerosol (600 m) was combined with a homogenous NO2 layer of 1.0 km. A layer of aerosol above the NO2 usually reduces the sensitivity of the satellite measurement. This situation is found mostly for runs with discrete elevated aerosol layers (representative for long-range transport) that can generate a decrease of the AMF values of up to 70%. The use of measured aerosol profiles and modelled NO2 resulted, generally, in much smaller changes of AMF relative to the pure Rayleigh case. Exceptions are some events of elevated layers with high aerosol optical depth that lead to a strong decrease of the AMF values. These results highlight the importance of aerosols in the retrieval of tropospheric NO2 columns from space and indicate the need for detailed information on aerosol properties and vertical distribution.

Estimation of Surface and Top-of-Atmosphere Shortwave Irradiance in Biomass-Burning Regions during SCAR-B

2000 ◽  
Vol 39 (10) ◽  
pp. 1742-1753 ◽  
Author(s):  
Sundar A. Christopher ◽  
Xiang Li ◽  
Ronald M. Welch ◽  
Jeffrey S. Reid ◽  
Peter V. Hobbs ◽  
...  
Keyword(s):  
Radiative Transfer ◽  
Biomass Burning ◽  
Optical Thickness ◽  
Radiative Forcing ◽  
Wavelength Dependence ◽  
Single Scattering ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Aerosol Radiative Forcing ◽  
Mean Square Errors

Abstract Using in situ measurements of aerosol optical properties and ground-based measurements of aerosol optical thickness (τs) during the Smoke, Clouds and Radiation—Brazil (SCAR-B) experiment, a four-stream broadband radiative transfer model is used to estimate the downward shortwave irradiance (DSWI) and top-of-atmosphere (TOA) shortwave aerosol radiative forcing (SWARF) in cloud-free regions dominated by smoke from biomass burning in Brazil. The calculated DSWI values are compared with broadband pyranometer measurements made at the surface. The results show that, for two days when near-coincident measurements of single-scattering albedo ω0 and τs are available, the root-mean-square errors between the measured and calculated DSWI for daytime data are within 30 W m−2. For five days during SCAR-B, however, when assumptions about ω0 have to be made and also when τs was significantly higher, the differences can be as large as 100 W m−2. At TOA, the SWARF per unit optical thickness ranges from −20 to −60 W m−2 over four major ecosystems in South America. The results show that τs and ω0 are the two most important parameters that affect DSWI calculations. For SWARF values, surface albedos also play an important role. It is shown that ω0 must be known within 0.05 and τs at 0.55 μm must be known to within 0.1 to estimate DSWI to within 20 W m−2. The methodology described in this paper could serve as a potential strategy for determining DSWI values in the presence of aerosols. The wavelength dependence of τs and ω0 over the entire shortwave spectrum is needed to improve radiative transfer calculations. If global retrievals of DSWI and SWARF from satellite measurements are to be performed in the presence of biomass-burning aerosols on a routine basis, a concerted effort should be made to develop methodologies for estimating ω0 and τs from satellite and ground-based measurements.

Planck-Weighted Transmittance and Correction of Solar Reflection for Broadband Infrared Satellite Channels

2012 ◽  
Vol 29 (3) ◽  
pp. 382-396 ◽  
Author(s):  
Yong Chen ◽  
Fuzhong Weng ◽  
Yong Han ◽  
Quanhua Liu
Keyword(s):  
Surface Temperature ◽  
Optical Thickness ◽  
Near Infrared ◽  
Spectral Response ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Atmospheric Layer ◽  
Explanatory Variables ◽  
Brightness Temperatures ◽  
Satellite Channels

Abstract The line-by-line radiative transfer model (LBLRTM) is used to derive the channel transmittances. The channel transmittance from a level to the top of the atmosphere can be approximated by three methods: Planck-weighted transmittance 1 (PW1), Planck-weighted transmittance 2 (PW2), and non-Planck-weighted transmittance (ORD). The PW1 method accounts for a radiance variation across the instrument’s spectral response function (SRF) and the Planck function is calculated with atmospheric layer temperature, whereas the PW2 method accounts for the variation based on the temperatures at the interface between atmospheric layers. For channels with broad SRFs, the brightness temperatures (BTs) derived from the ORD are less accurate than these from either PW1 or PW2. Furthermore, the BTs from PW1 are more accurate than these from PW2, and the BT differences between PW1 and PW2 increase with atmospheric optical thickness. When the band correction is larger than 1, the PW1 method should be used to account for the Planck radiance variation across the instrument’s SRF. When considering the solar contribution in daytime, the correction of the solar reflection has been made for near-infrared broadband channels (~3.7 μm) when using PW1 transmittance. The solar transmittance is predicted by using explanatory variables, such as PW1 transmittance, the secant of zenith angle, and the surface temperature. With this correction, the errors can be significantly reduced.

scholarly journals Vicarious Calibration of FengYun-3D MERSI-II at Railroad Valley Playa Site: A Case for Sensors with Large View Angles

2021 ◽  
Vol 13 (7) ◽  
pp. 1347
Author(s):  
Yepei Chen ◽  
Kaimin Sun ◽  
Wenzhuo Li ◽  
Xiuqing Hu ◽  
Pengfei Li ◽  
...  
Keyword(s):  
Field Measurements ◽  
Calibration Method ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Radiometric Calibration ◽  
Vicarious Calibration ◽  
In Situ Data ◽  
Benchmark Datasets ◽  
Moderate Resolution Imaging Spectroradiometer

Vicarious calibration, as one on-orbit calibration method, is a supplement to onboard calibration of sensors. The application of vicarious calibration, however, is greatly limited due to the time- and effort-consuming field measurements of atmosphere and surface. Fortunately, the Radiometric Calibration Network (RadCalNet) provides automated in situ data at multiple sites, thus increasing the opportunities to achieve ongoing ground-reference calibration of in-orbit instruments. The MEdium Resolution Spectrum Imager-II (MERSI-II) onboard FengYun-3D (FY) has the temporal, spectral, spatial, and radiometric capacity for image capture at a level on par with other sensors used worldwide, such as the Moderate Resolution Imaging Spectroradiometer (MODIS). Its on-orbit radiometric performance, however, is assessed in a limited manner. In this study, the reflectance-based vicarious calibration method was employed to calibrate the MERSI-II sensor using ground measurements from RadCalNet at the Railroad Valley Playa site. The calibration of the MERSI-II sensor with large view angles presents difficulties due to the uncertainties introduced by surface bidirectional reflectance distribution function (BRDF) effects. Thus, we performed BRDF correction to harmonize the sensor and ground measurements to consistent observation geometries, before the in-situ measurements were taken as inputs for the 6SV radiative transfer model to predict at-sensor radiance. The calibration results were comprehensively validated with ground data and MODIS benchmark datasets. The results show that accounting for BRDF correction could improve the accuracy of vicarious calibration and ensure inter-consistency between different sensors. An analysis of the vicarious calibration of FY-3D MERSI-II yielded uncertainties of <5% for solar reflective bands, which meets the radiometric accuracy requirements typical for land-monitoring space missions. The proposed approach is also applicable to the calibration of other large footprint sensors.

scholarly journals A method to retrieve the spectral complex refractive index and single scattering optical properties of dust deposited in mountain snow

2016 ◽  
Vol 63 (237) ◽  
pp. 133-147 ◽  
Author(s):  
S. McKENZIE SKILES ◽  
THOMAS PAINTER ◽  
GREGORY S. OKIN
Keyword(s):  
Refractive Index ◽  
Optical Properties ◽  
Radiative Transfer ◽  
Near Infrared ◽  
Direct Reduction ◽  
Complex Refractive Index ◽  
Single Scattering ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Dust Deposition

ABSTRACTDust deposition to snow can have regionally important climatic and hydrologic impacts resulting from direct reduction of surface albedo and indirectly from the initiation of snow albedo feedbacks. Modeling the radiative impacts of dust deposited in snow requires knowledge of the optical properties of both components. Here we present an inversion technique to retrieve the effective optical properties of dust deposited in mountain snow cover from measurements of hemispherical dust reflectance and particle size distributions using radiative transfer modeling. First, modeled reflectance is produced from single scattering properties modeled with Mie theory for a specified grain size distribution over a range of values for the imaginary part of the complex refractive index (k = 0.00001–0.1). Then, a multi-step look-up table process is employed to retrieve kλ and single scattering optical properties by matching measured to modeled reflectance across the shortwave and near infrared. The real part of the complex refractive index, n, for dust aerosols ranges between 1.5 and 1.6 and a sensitivity analysis shows the method is relatively insensitive to the choice of n within this range, 1.525 was used here. Using the values retrieved by this method to update dust optical properties in a snow + aerosol radiative transfer model reduces errors in springtime albedo modeling by 50–70%.

scholarly journals A neural network radiative transfer model approach applied to TROPOMI’s aerosol height algorithm

2019 ◽  
Author(s):  
Swadhin Nanda ◽  
Martin de Graaf ◽  
J. Pepijn Veefkind ◽  
Mark ter Linden ◽  
Maarten Sneep ◽  
...  
Keyword(s):  
Neural Network ◽  
Radiative Transfer ◽  
Near Infrared ◽  
Forward Model ◽  
Radiative Transfer Model ◽  
Retrieval Algorithm ◽  
Transfer Model ◽  
Aerosol Layer ◽  
Neural Network Models ◽  
Layer Height

Abstract. To retrieve aerosol properties from satellite measurements of the oxygen A-band in the near infrared, a line-by-line radiative transfer model implementation requires a large number of calculations. These calculations severely restrict a retrieval algorithm's operational capability as it can take several minutes to retrieve aerosol layer height for a single ground pixel. This paper proposes a forward modeling approach using artificial neural networks to speed up the retrieval algorithm. The forward model outputs are trained into a set of neural network models to completely replace line-by-line calculations in the operational processor. Results of comparing the forward model to the neural network alternative show encouraging results with good agreements between the two when applied to retrieval scenarios using both synthetic and real measured spectra from TROPOMI (TROPOspheric Monitoring Instrument) on board the ESA Sentinel-5 Precursor mission. With an enhancement of the computational speed by three orders of magnitude, TROPOMI's operational aerosol layer height processor is now able to retrieve aerosol layer heights well within operational capacity.

scholarly journals Remote sensing of aerosol properties from multi-wavelength and multi-pixel information over the ocean

2018 ◽  
Author(s):  
Chong Shi ◽  
Makiko Hashimoto ◽  
Teruyuki Nakajima
Keyword(s):  
Remote Sensing ◽  
Spatial Variation ◽  
Optical Thickness ◽  
Measurement Errors ◽  
Near Infrared ◽  
Aerosol Optical Thickness ◽  
Dust Particles ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Satellite Measurements

Abstract. In this study, we investigate the feasibility of multi-pixel scheme in the inversion of aerosol optical thickness (AOT) for multi-spectral satellite instruments over the ocean. Different from the traditional satellite aerosol retrievals conducted pixel by pixel independently, we derive the aerosol optical thickness of multiple pixels simultaneously by adding smoothness constraint on the spatial variation of aerosols and oceanic substances, which helps the satellite retrieval with higher consistency from pixel to pixel. Simulations are performed for two representative oceanic circumstances – open and coastal waters, as well as the land-ocean interface region. We retrieve the AOT for fine, sea spray, and dust particles simultaneously using synthetic spectral measurements from the Greenhouse Gases Observing Satellite/Thermal and Near Infrared Sensor for Carbon Observations-Cloud and Aerosol Imager (GOSAT/TANSO-CAI) with four wavelengths coving from the ultraviolet to shortwave infrared bands. The forward radiation calculation is performed by a coupled atmosphere-ocean radiative transfer model combined with a three-component bio-optical oceanic module, where the chlorophyll a concentration, sediment and colored dissolved organic matter are considered. Results show that accuracies of the derived AOT and spectral remote-sensing reflectance are both improved by applying smoothness constraints on the spatial variation of aerosol and oceanic substances in homogeneous or inhomogeneous surface conditions. The multi-pixel scheme can be effective to compensate the retrieval biases induced by measurement errors and improve the retrieval sensitivity, particularly for the fine aerosol over the coastal water. We then apply the algorithm to derive AOTs using real satellite measurements. Results indicate that the multi-pixel method helps to polish the irregular retrieved results of the satellite imagery and shows promising potentiality to correct the overestimation of aerosols over high turbid waters, by benefiting from the coincident retrieval of neighboring pixels. A comparison of retrieved AOTs from satellite measurements with those from the Aerosol Robotic Network (AERONET) also indicates that retrievals conducted by the multi-pixel scheme are more consistent with the AERONET observations.

Sign in / Sign up

Export Citation Format

Share Document