Millable Polyurethane/Organoclay Nanocomposites: Preparation, Characterization, and Properties

2007 ◽  
Vol 7 (2) ◽  
pp. 634-640 ◽  
Author(s):  
M. Siliani ◽  
M. A. López-Manchado ◽  
J. L. Valentín ◽  
M. Arroyo ◽  
A. Marcos ◽  
...  
Keyword(s):  
Barrier Properties ◽  
Substantial Improvement ◽  
Nanometer Scale ◽  
X Ray Diffraction ◽  
Transformation Techniques ◽  
Covalent Bonds ◽  
X Ray ◽  
Transmission Electron ◽  
Organically Modified ◽  
Diffraction Patterns

Novel millable polyurethane (PU)/organoclay nanocomposites have been successfully prepared by conventional transformation techniques. One natural (C6A) and two organically modified (C15A and C30B) montmorillonites have been used as clays for preparing PU nanocomposites. The optimum dispersion of nanofiller at a nanometer scale in PU matrix was confirmed by X-ray diffraction patterns and transmission electron microscopy. A substantial improvement of the PU properties by addition of only a small amount of organoclay was observed. It is worthy to note that the organoclays show a different interfacial interaction with the PU matrix, which was reflected in different macroscopic properties. Thus, C30B organoclay seems to react with PU chains to form covalent bonds, while C15Aonly interacts physically with PU chains. Mechanical and barrier properties are analyzed.

Cetyltrimethylammonium bromide- and ethylene glycol-assisted preparation of mono-dispersed indium oxide nanoparticles using hydrothermal method

2014 ◽  
Vol 68 (8) ◽  
Author(s):  
Selvakumar Dhanasingh ◽  
Dharmaraj Nallasamy ◽  
Saravanan Padmanapan ◽  
Vinod Padaki
Keyword(s):  
Ethylene Glycol ◽  
Hydrothermal Method ◽  
Indium Oxide ◽  
Cetyltrimethylammonium Bromide ◽  
Oxide Nanoparticles ◽  
X Ray Diffraction ◽  
Hydrothermal Conditions ◽  
X Ray ◽  
Transmission Electron ◽  
Diffraction Patterns

AbstractThe influence of cetyltrimethylammonium bromide and ethylene glycol on the size and dispersion of indium oxide nanoparticles prepared under hydrothermal conditions was investigated. The precursor compound, indium hydroxide, obtained by the hydrothermal method in the absence as well as the presence of cetyltrimethylammonium bromide, was converted to indium oxide by sintering at 400°C. The formation of nanoscale indium oxide upon sintering was ascertained by the characteristic infrared adsorption bands and X-ray diffraction patterns of indium oxide. Transmission electron microscopy and band gap values confirmed that the cetyltrimethylammonium bromide facilitated the formation of indium oxide nanoparticles smaller in size and narrower in distribution than those prepared without the assistance of cetyltrimethylammonium bromide.

Facile Refluxing Synthesis of Hydroxyapatite Nanoparticles

2015 ◽  
Vol 68 (8) ◽  
pp. 1293 ◽  
Author(s):  
Pakvipar Chaopanich ◽  
Punnama Siriphannon
Keyword(s):  
Crystallite Size ◽  
Reaction Times ◽  
Single Step ◽  
Hydroxyapatite Nanoparticles ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Aqueous Mixture ◽  
Diffraction Patterns ◽  
Microscopy Images

Hydroxyapatite (HAp) nanoparticles were successfully synthesized from an aqueous mixture of Ca(NO3)2·4H2O and (NH4)2HPO4 by a facile single-step refluxing method using polystyrene sulfonate (PSS) as a template. The effects of reaction times, pH, and PSS concentration on the HAp formation were investigated. It was found that the crystalline HAp was obtained under all conditions after refluxing the precursors for 3 and 6 h. The longer refluxing time, the greater the crystallinity and the larger the crystallite size of the HAp nanoparticles. The HAp with poor crystallinity was obtained at pH 8.5; however, the well-crystallized HAp was obtained when reaction pH was increased to 9.5 and 10.5. In addition, the X-ray diffraction patterns revealed that the presence of PSS template caused the reduction of HAp crystallite size along the (002) plane from 52.6 nm of non-template HAp to 43.4 nm and 41.4 nm of HAp with 0.05 and 0.2 wt-% PSS template, respectively. Transmission electron microscopy images of the synthesized HAp revealed the rod-shaped crystals of all samples. The synthesized HAp nanoparticles were modified by l-aspartic acid (Asp) and l-arginine (Arg), having negative and positive charges, respectively. It was found that the zeta potential of HAp was significantly changed from +5.46 to –24.70 mV after modification with Asp, whereas it was +4.72 mV in the Arg-modified HAp. These results suggested that the negatively charged amino acid was preferentially adsorbed onto the synthesized HAp surface.

scholarly journals Synthesis, Physical Properties and Enzymatic Degradation of Biodegradable Nanocomposites Fabricated Using Poly(Butylene Carbonate-Co-Terephthalate) and Organically Modified Layered Zinc Phenylphosphonate

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 2149
Author(s):  
Li-Ying Tseng ◽  
Erh-Chiang Chen ◽  
Jie-Mao Wang ◽  
Tzong-Ming Wu
Keyword(s):  
Nmr Spectra ◽  
Enzymatic Degradation ◽  
Molar Ratio ◽  
Wide Angle ◽  
Mixing Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Organically Modified ◽  
Biodegradable Nanocomposites

A new biodegradable aliphatic-aromatic poly (butylene carbonate-co-terephthalate) (PBCT-85) with the molar ratio [BC]/[BT] = 85/15, successfully synthesized through transesterification and polycondensation processes, was identified using 1H-NMR spectra. Various weight ratios of PBCT/organically modified layered zinc phenylphosphonate (m-PPZn) nanocomposites were manufactured using the solution mixing process. Wide-angle X-ray diffraction and transmission electron microscopy were used to examine the morphology of PBCT-85/m-PPZn nanocomposites. Both results exhibited that the stacking layers of m-PPZn were intercalated into the PBCT-85 polymer matrix. The additional m-PPZn into PBCT-85 copolymer matrix significantly enhanced the storage modulus at −70 °C, as compared to that of neat PBCT-85. The lipase from Pseudomonas sp. was used to investigate the enzymatic degradation of PBCT-85/m-PPZn nanocomposites. The weight loss decreased as the loading of m-PPZn increased, indicating that the existence of m-PPZn inhibits the degradation of the PBCT-85 copolymers. This result might be attributed to the higher degree of contact angle for PBCT-85/m-PPZn nanocomposites. The PBCT-85/m-PPZn composites approved by MTT assay are appropriate for cell growth and might have potential in the application of biomedical materials.

A Chemical Solution Route to Rapid Synthesis of Homogeneous Bi100−xSbx Alloys Nanoparticles at Room Temperature

2007 ◽  
Vol 7 (2) ◽  
pp. 525-529 ◽  
Author(s):  
Bo Zhou ◽  
Jun-Jie Zhu
Keyword(s):  
Room Temperature ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Solution Route ◽  
Diffraction Patterns ◽  
Co Reduction ◽  
Chemical Solution Route

A chemical co-reduction route in aqueous solution was developed to synthesize Bi100−xSbx alloys at room temperature. The hydrolyses of Bi(III) and Sb(III) were effectively avoided by selecting proper raw materials and coordinator. X-ray diffraction analysis indicated that the as-prepared Bi100−xSbx alloys were homogeneous and phase-pure, and the Bi/Sb ratios in the alloys were very close to those in the aqueous solutions. The transmission electron microscope observation showed that the as-prepared Bi100−xSbx (x = 0∼100) alloys were particles with a size of tens of nanometers. The selected area electron diffraction patterns confirmed the high crystallinity, the homogeneousness, and the composition controllability of as-prepared alloys. All these characters and the nanometer-scaled size of the alloys are believed to be beneficial to the thermoelectric property of the Bi100−xSbx alloys.

scholarly journals Enzymatic Degradation of Acrylic Acid-Grafted Poly(butylene succinate-co-terephthalate) Nanocomposites Fabricated Using Heat Pressing and Freeze-Drying Techniques

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 376 ◽  
Author(s):  
Sheng-Hsiang Lin ◽  
Hsiang-Ting Wang ◽  
Jie-Mao Wang ◽  
Tzong-Ming Wu
Keyword(s):  
Acrylic Acid ◽  
Freeze Drying ◽  
Crystallization Rate ◽  
X Ray Diffraction ◽  
Butylene Succinate ◽  
Covalent Bonds ◽  
Polymer Backbone ◽  
Transmission Electron ◽  
Degradation Rates ◽  
Organically Modified

Biodegradable acrylic acid-grafted poly(butylene succinate-co-terephthalate) (g-PBST)/organically modified layered zinc phenylphosphonate (m-PPZn) nanocomposites were effectively fabricated containing covalent bonds between the g-PBST and m-PPZn. The results of wide-angle X-ray diffraction and transmission electron microscopy revealed that the morphology of the g-PBST/m-PPZn nanocomposites contained a mixture of partially exfoliated or intercalated conformations. The isothermal crystallization behavior of the nanocomposites showed that the half-time for crystallization of 5 wt % g-PBST/m-PPZn nanocomposites was less than 1 wt % g-PBST/m-PPZn nanocomposites. This finding reveals that increasing the loading of m-PPZn can increase the crystallization rate of nanocomposites. Degradation tests of g-PBST/m-PPZn nanocomposites fabricated using the heat pressing and the freeze-drying process were performed by lipase from Pseudomonas sp. The degradation rates of g-PBST-50/m-PPZn nanocomposites were significantly lower than those of g-PBST-70/m-PPZn nanocomposites. The g-PBST-50 degraded more slowly due to the higher quantity of aromatic group and increased stiffness of the polymer backbone. The degradation rate of the freeze-drying specimens contained a more extremely porous conformation compared to those fabricated using the heat pressing process.

scholarly journals The Reliability Improvement of Cu Interconnection by the Control of Crystallizedα-Ta/TaNxDiffusion Barrier

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Wei-Lin Wang ◽  
Chia-Ti Wang ◽  
Wei-Chun Chen ◽  
Kuo-Tzu Peng ◽  
Ming-Hsin Yeh ◽  
...  
Keyword(s):  
Diffusion Barrier ◽  
Practical Application ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
X Ray ◽  
Reliability Improvement ◽  
N Concentration ◽  
Transmission Electron ◽  
Diffraction Patterns ◽  
Interconnection Structure

Ta/TaN bilayers have been deposited by a commercial self-ionized plasma (SIP) system. The microstructures of Ta/TaN bilayers have been systematically characterized by X-ray diffraction patterns and cross-sectional transmission electron microscopy. TaN films deposited by SIP system are amorphous. The crystalline behavior of Ta film can be controlled by the N concentration of underlying TaN film. On amorphous TaN film with low N concentration, overdeposited Ta film is the mixture ofα- andβ-phases with amorphous-like structure. Increasing the N concentration of amorphous TaN underlayer successfully leads upper Ta film to form pureα-phase. For the practical application, the electrical property and reliability of Cu interconnection structure have been investigated by utilizing various types of Ta/TaN diffusion barrier. The diffusion barrier fabricated by the combination of crystallizedα-Ta and TaN with high N concentration efficiently reduces the KRc and improves the EM resistance of Cu interconnection structure.

Homogeneity in the Polyether Alkoxide Sol‐Gel Synthesis of YBa2Cu3O7-δ

1994 ◽  
Vol 346 ◽  
Author(s):  
Carol S. Houk ◽  
Gary A. Burgoine ◽  
Catherine J. Page
Keyword(s):  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Diffraction Patterns ◽  
Mapping Techniques ◽  
Starting Solutions ◽  
Average Size ◽  
Sol Gel Synthesis ◽  
Elemental Maps

ABSTRACTWe have investigated the homogeneity of sol‐gel derived YBa2Cu307‐s from the solution phase to the final product using transmission electron microscopy (TEM), x‐ray diffraction (XRD), and Energy Dispersive X‐ray (EDX) lateral mapping techniques. The starting solutions contain stoichiometric amounts of the metal 2‐(2‐methoxyethoxy)ethoxide components in 2‐(2‐methoxyethoxy)ethanol and appear to be homogeneous by TEM with a uniform distribution of particles having an average size of less than 40 â. Through elemental mapping we see elemental segregation in the high temperature (950 °C) products, which are orthorhombic by XRD. In elemental maps of gel samples fired to 700 °C, which are tetragonal by XRD, we also see elemental inhomogeneity within particles and phase zoning in maps of products from finely ground gels. A comparison of elemental maps and x‐ray diffraction patterns of the products from gel processing and conventional solid state processing is made.

Structural properties of molecular beam epitaxy grown Ni/Pt superlattices

1997 ◽  
Vol 12 (1) ◽  
pp. 161-174 ◽  
Author(s):  
W. Staiger ◽  
A. Michel ◽  
V. Pierron-Bohnes ◽  
N. Hermann ◽  
M. C. Cadeville
Keyword(s):  
Molecular Beam ◽  
Growth Direction ◽  
Misfit Dislocations ◽  
X Ray Diffraction ◽  
Plan View ◽  
X Ray ◽  
Transmission Electron ◽  
Superlattice Peak ◽  
Diffraction Peaks ◽  
Diffraction Patterns

We find that the [Ni3.2nmPt1.6nm] × 15 and [Ni3.2nmPt0.8nm] × 15 multilayers are semicoherent and display a columnar morphology. From both the period of the moir’e fringes and the positions of the diffraction peaks in electronic (plan-view and crosssection geometries) and x-ray diffraction patterns, one deduces that the nickel is relaxed (at least in the error bars of all our measurements), whereas the platinum remains slightly strained (≈−1%). The interfaces are sharp; no intermixing takes place giving rise to neat contrasts in transmission electron microscopy (TEM) and to high intensities of the superlattice peaks in the growth direction in both diffraction techniques. The relaxation of the interfacial misfit occurs partially through misfit dislocations, partially through the strain of platinum. A quasiperiodic twinning occurs at the interfaces, the stacking fault which forms the twin being the most often located at the interface Pt/Ni, i.e., when a Pt layer begins to grow on the Ni layer. The simulation of the θ/2θ superlattice peak intensities takes into account the columnar microstructure. It shows that the roughness is predominantly at medium scale with a fluctuation of about 12.5% for Ni layers and negligible for Pt layers.

The Microstructure of Fe7C3 Formed at 300°C by Plasma Enhanced Chemical Vapor Deposition (PECVD)

1993 ◽  
Vol 313 ◽  
Author(s):  
H. Siriwardane ◽  
P. Fraundorf ◽  
J.W. Newkirk ◽  
O.A. Pringle ◽  
W.J. James
Keyword(s):  
Oxidation Process ◽  
Iron Carbide ◽  
Chemical Vapor ◽  
Carbon Films ◽  
Corrosion And Wear ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Iron Phase ◽  
Diffraction Patterns

Thin iron carbide films were prepared by introducing iron penta carbonyl (FeCO5) and hydrogen (H2) into a glow discharge. The films are of potential interest in corrosion and wear resistant applications. X-ray diffraction data of films (≈ 7000 Å thick) deposited on glass at 300°C evidenced only Fe7C3. Thinner films were required for examination by analytical and high resolution transmission electron Microscopy. Therefore, two sets of films (“thin” < 200 Å and “thick” ≈ 800 Å) were plasma-deposited on carbon or holey carbon films supported on copper grids. The thin TEM specimens exhibited a fine texture and gave rise to ring diffraction patterns, whereas the thick TEM specimens evidenced two types of structure: (i) half-Micron sized grains separated from one another by 1–2 Microns on the support, although sometimes interconnected by single crystal platelets and (ii) 300 Å grapelike clumps of 100–200 Å crystals, each individually surrounded by a 50 Å non-crystalline coating. The latter structure may result from a post-formation oxidation process which expels carbon from the iron phase into grain boundaries.

Evolution of Nanoindentation Hardness of Fe/Cu Nanometer-Scale Multilayers by Magnetron Sputtering

2008 ◽  
Vol 373-374 ◽  
pp. 104-107 ◽  
Author(s):  
J. Gao ◽  
Z.L. Wu ◽  
Z.P. Zhang ◽  
B.S. Cao ◽  
M.K. Lei
Keyword(s):  
Magnetron Sputtering ◽  
Nanometer Scale ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
X Ray ◽  
Transmission Electron ◽  
Modulus Difference ◽  
Nanoindentation Hardness ◽  
Modulation Wavelength ◽  
Peak Value

Fe/Cu nanometer-scale multilayers with nominal modulation wavelengths ranging from 5 to 40 nm are deposited by direct current magnetron sputtering on Si (100) substrates. Modulation structures of the multilayers are examined by small angle / wide angle x-ray diffraction (SA/WAXRD) and cross-sectional transmission electron microscopy (XTEM). Hardness of the multilayers is measured by using nanoindentation. All the multilayers have Fe (110) and Cu (111) textures. Interface coherency is observed in the multilayers with designed modulation wavelengths of 5 and 10 nm. The hardness increases firstly and then deceases with increasing the modulation wavelength, and reaches peak value of 7.29±0.29 GPa in the multilayers with nominal modulation wavelength of 10 nm. The evolution of the hardness of the mulitlayers is explained by interface width and modulus difference between sublayers.

Sign in / Sign up

Export Citation Format

Share Document