scholarly journals Study on Dynamic Evolution of Roof Crack and Support Timing of Secondary Tunneling for Large Section Open-Off Cut in Deep Mines

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Shuaigang Liu ◽  
Jianbiao Bai ◽  
Xiangyu Wang ◽  
Bowen Wu ◽  
Guanghui Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Failure Mode ◽  
Roof Rock ◽  
Large Section ◽  
Rock Stratum ◽  
Damage Degree ◽  
Key Factor ◽  
Large Mining Height ◽  
Control Technologies ◽  
The Stability

The stability of large section open-off cut in deep mines (LODM) is the key factor affecting the normal equipment installation and safe mining in fully mechanized top-coal caving face. The mechanical model shows that the deflection of the roof of the LODM is proportional to the cubic of span. In this paper, UDEC Trigon model is established, and the parameters of different coal measures strata are modified in detail. The evolution law, failure mode, and damage degree of roof cracks in secondary tunneling are studied, and the roof support effect is analyzed. The numerical simulation results show that the process of roof crack evolution after the primary excavation section and the second excavation section can be divided into three stages according to microseismic activities, and the reasonable supporting time can control the propagation of roof microcracks and reduce the development height of macrocracks. The rock bridge existing in the roof rock stratum after the combined support of long and short anchor cables can effectively limit the formation of macrocracks and their interaction; especially the key support in the interface area can reduce the development height of roof cracks in secondary tunneling and weaken the damage degree of roof rock stratum in the LODM. The field test shows that the moved volume of rib-to-rib and roof-to-floor of the LODM is stable at about 350 mm and 550 mm, respectively. The numerical simulation in this paper is helpful to understand the failure mode of roof in LODM with large mining height and provides a method for the design of its control technologies.

scholarly journals Research on Technology of Supporting in Super-Large Section Cut in Working Face with Large Mining Height

2021 ◽  
Vol 2021 ◽  
pp. 1-6
Author(s):  
Zhicheng Ren ◽  
Minghui Zuo
Keyword(s):  
Large Section ◽  
Rock Stratum ◽  
Working Face ◽  
Structure Detection ◽  
Fracture Area ◽  
Large Mining Height ◽  
Design Plan ◽  
Computer Numerical Simulation ◽  
Roof Strata ◽  
Mining Height

For the support problem of the super-large section cut in working face with large mining height, the 1105 cut pilot chamber of Zhaogu No. 2 Mine, the roof strata structure detection and the strata movement rule research were conducted. The results prove that concentrate fracture area, gradually sparse fracture area, and rare fracture area regularly distributed from the surface to the deep area of the roof of 1105 cut, and less fracture exists in the rock stratum of roof above 3.5 m, and the stratum of roof within the range of 4–6 m is stable. Authors propose the long bolt and cable combined supporting technology and optimized the design plan applying theoretical calculation and computer numerical simulation. The scheme has been applied in the field of the 1105 super-large section cut in Zhaogu No. 2 Mine. The monitoring results show that the scheme can effectively control surrounding rock of roadway, and the support with long bolt has good effectiveness.

scholarly journals The Supporting Technology Research in Large Section Inclined Shaft with Fracture and Soft Surrounding Rock

2015 ◽  
Vol 9 (1) ◽  
pp. 450-456 ◽  
Author(s):  
Peng Wen-qing ◽  
Wang Xin-min ◽  
Wang Wei-jun
Keyword(s):  
Numerical Simulation ◽  
Reaction Force ◽  
Surrounding Rock ◽  
Bending Stress ◽  
Technology Research ◽  
Large Section ◽  
Stability Of Surrounding Rock ◽  
Mechanical Models ◽  
The Stability ◽  
Accuracy Of Results

This paper is based on the large section inclined shaft crossing goaf of Pingdingshan No.6 Mine as engineering background, and aimed at solving the difficult supporting problem of fractured surrounding rock. After establishing and calculating the mechanical models of U-steel and inverted arch, the support’s vertical reaction force (N1) and horizontal counterforce (X1) are determined as 180.96 KN and 48.12 KN, while the maximum bending stress (σmax) and ultimate bearing capacity of the inverted arch are obtained as 375.59 Mpa and 0.27 Mpa. It shows that the deformation of surrounding rock is well controlled by the supporting structure. The numerical simulation model is built by using the software FLAC3D to analyze the stability of surrounding rock after supporting. The results suggest that the deformation of roof, floor and sides is reduced by 17%, 23% and 71% respectively after supporting with U-steel in the inclined shaft, and the accuracy of results has been verified by a field experiment. Therefore, the “U-steel+ pouring concrete + inverted arch + backwall grouting” technology can effectively control the damage of surrounding rock and improve the stability of surrounding rock.

scholarly journals Procedure for the Selection of Rubber Compound in Rubber-Metal Springs for Vibration Isolation

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1737
Author(s):  
Milan Banić ◽  
Dušan Stamenković ◽  
Aleksandar Miltenović ◽  
Dragan Jovanović ◽  
Milan Tica
Keyword(s):  
Numerical Simulation ◽  
Constitutive Model ◽  
Vibration Isolation ◽  
Correct Selection ◽  
Virtual Experiment ◽  
Rubber Compound ◽  
Key Factor ◽  
Railway Engineering ◽  
Selection Of

The selection of a rubber compound has a determining influence on the final characteristics of rubber-metal springs. Therefore, the correct selection of a rubber compound is a key factor for development of rubber-metal vibration isolation springs with required characteristics. The procedure for the selection of the rubber compound for vibration isolation of rubber-metal springs has been proposed, so that the rubber-metal elements have the necessary characteristics, especially in terms of deflection. The procedure is based on numerical simulation of spring deflection with Bergström-Boyce constitutive model in virtual experiment, with a goal to determine which parameters of the constitutive model will lead to spring required deflection. The procedure was verified by case study defined to select rubber compound for a rubber–metal spring used in railway engineering.

scholarly journals Study on instability failure mode and monitoring early warning standard of surrounding rock in fully weathered argillaceous sandstone section of large section tunnel

2019 ◽  
Vol 136 ◽  
pp. 04023
Author(s):  
Ming Zhao ◽  
Ke Li ◽  
Hong Yan Guo ◽  
KaiCheng Hua
Keyword(s):  
Limit State ◽  
Stable State ◽  
Simulation Software ◽  
Surrounding Rock ◽  
Large Section ◽  
Rock Stability ◽  
Geological Conditions ◽  
Construction Step ◽  
The Face ◽  
The Stability

Based on the special geological conditions of a tunnel in Qingyuan section of Huizhou-Zhanzhou Expressway, FLAC3d numerical simulation software is used to simulate the rheological properties and instability of surrounding rock in large-section fully weathered sandstone section, and the stability and loss of surrounding rock are analyzed. The deformation of the dome and the face at steady state is analyzed. It is found that: 1) when the surrounding rock is in a stable state, the deformation curve of the dome is smooth. When the surrounding rock of the face is unstable, the front of the face appears ahead. Deformation should be first strengthened on the surrounding rock in front of the face. 2) The arched foot is an important part of the instability of the surrounding rock. In order to prevent the expansion of the collapsed part, the arched part should be reinforced. 3) In order to obtain the limit state of surrounding rock stability, the strength of surrounding rock is reduced, and the strength reduction coefficient corresponding to the displacement sudden point is taken as the safety factor of rock stability around the hole, and the stability safety coefficients of surrounding rock of each construction step are greater than 1.2. 4) The dynamic standard values of deformation control in the whole construction stage are obtained by analyzing the deformation curves of each data monitoring point with time in the corresponding time period of each construction step.

STABILITY OF TWO TYPICAL COMPLEX DYNAMICAL NETWORKS

2008 ◽  
Vol 22 (05) ◽  
pp. 553-560 ◽  
Author(s):  
WU-JIE YUAN ◽  
XIAO-SHU LUO ◽  
PIN-QUN JIANG ◽  
BING-HONG WANG ◽  
JIN-QING FANG
Keyword(s):  
Numerical Simulation ◽  
Dissipative System ◽  
Small World ◽  
Complex Dynamical Networks ◽  
Dynamical Networks ◽  
Scale Free ◽  
Scale Free Networks ◽  
General Complex ◽  
The Stability ◽  
Theoretical Results

When being constructed, complex dynamical networks can lose stability in the sense of Lyapunov (i. s. L.) due to positive feedback. Thus, there is much important worthiness in the theory and applications of complex dynamical networks to study the stability. In this paper, according to dissipative system criteria, we give the stability condition in general complex dynamical networks, especially, in NW small-world and BA scale-free networks. The results of theoretical analysis and numerical simulation show that the stability i. s. L. depends on the maximal connectivity of the network. Finally, we show a numerical example to verify our theoretical results.

The Compliance Method for Measurement of Near Surface Residual Stresses—Analytical Background

1994 ◽  
Vol 116 (4) ◽  
pp. 550-555 ◽  
Author(s):  
M. Gremaud ◽  
W. Cheng ◽  
I. Finnie ◽  
M. B. Prime
Keyword(s):  
Numerical Simulation ◽  
Residual Stresses ◽  
Random Errors ◽  
Residual Stress Field ◽  
Near Surface ◽  
Surface Residual Stresses ◽  
Zero Shift ◽  
Stress States ◽  
The Stability ◽  
Piecewise Functions

Introducing a thin cut from the surface of a part containing residual stresses produces a change in strain on the surface. When the strains are measured as a function of the depth of the cut, residual stresses near the surface can be estimated using the compliance method. In previous work, the unknown residual stress field was represented by a series of continuous polynomials. The present paper shows that for stress states with steep gradients, superior predictions are obtained by using “overlapping piecewise functions” to represent the stresses. The stability of the method under the influence of random errors and a zero shift is demonstrated by numerical simulation.

Release Profile of a Model Protein Drug Depending on the Stability of Microspheres Based on Polyelectrolyte Complex

2007 ◽  
Vol 342-343 ◽  
pp. 505-508
Author(s):  
Sung Won Kim ◽  
Yun Sik Nam ◽  
Yeon Jin Min ◽  
Jong Ho Kim ◽  
Kwang Meyong Kim ◽  
...  
Keyword(s):  
Polyelectrolyte Complex ◽  
Coating Layer ◽  
Great Influence ◽  
Release Profile ◽  
Core Material ◽  
Glycol Chitosan ◽  
The Core ◽  
Key Factor ◽  
Model Protein ◽  
The Stability

Stability and disintegration of natural polyelectrolyte complex microspheres for protein drugs delivery have been extensively investigated because of their great influence on the drug release patterns. In this study, we tested stability of microspheres with alginate (Alg) core layered by either chitosan (Chi) or glycol chitosan (GChi) by examining release profiles of fluorophorelabeled bovine serum albumin (BSA) and lysozyme (Lys) from the microspheres. While GChi shell was disintegrated quickly, Chi-shell microspheres showed good stability in PBS. Disintegration of the coated layer induced the core material instable. The results indicated that while the charges of the shell material provided additional diffusion barrier against the protein release, the key factor to hold the proteins inside the microspheres was the integrity of the outer coating layer.

Basic Experimental and Numerical Investigations on Chip Pressing

2013 ◽  
Vol 554-557 ◽  
pp. 630-637 ◽  
Author(s):  
Martin Grüner ◽  
Marion Merklein
Keyword(s):  
Numerical Simulation ◽  
Aluminium Alloys ◽  
Testing Machine ◽  
Material Model ◽  
Extrusion Process ◽  
Milling Process ◽  
Numerical Investigations ◽  
Compression Direction ◽  
Universal Testing ◽  
The Stability

Aluminium alloys show a great potential for lightweight constructions due to their high strength and low density but the production of this material is very energy consuming. Also the recycling of aluminium alloys, e.g. chips from the milling process, shows different challenges. Beside contamination by cooling lubricant and oxidation of the surface of the chips the melting and rolling process for new semi finish products needs a high amount of energy. TEKKAYA shows a new approach for recycling of aluminium alloy chips by an extrusion process at elevated temperatures producing different kinds of profiles. A new idea is the production of components directly out of chips using severe plastic deformation for joining of the chips similar to the accumulative roll bonding process in sheet metal forming. In a first approach aluminium alloy chips out of a milling process were uniaxial compressed with different loads inside an axisymmetric tool installed in a universal testing machine. The compressed chip disks subsequently were tested with two experiments to gain information on their stability. First experiment is a disk compression test with the disk standing on its cylindrical surface, giving information on the stability perpendicular to the compression direction. Second experiment is a stacked disk compression test with three disks to investigate the stability parallel to compression direction. During all three tests force and displacement values are recorded by the universal testing machine. These data are also processed to calculate or identify input parameters for the numerical investigations. For numerical simulation ABAQUS in conjunction with the Drucker-Prager-Cap material model, which is often used for sintering processes, seems to be a good choice. By numerical simulation of the experiments and comparison with the experiments input parameters for the material model can be identified showing good accordance. This material model will be used in future numerical investigations of an extrusion process to identify tool geometries leading to high strains inside the material and by this to an increased stability of the parts.

Application of ABAQUS in Surrounding Rock Stability Analysis of Shallow Large Cross-Section Tunnel

2015 ◽  
Vol 777 ◽  
pp. 8-12 ◽  
Author(s):  
Lin Zhen Cai ◽  
Cheng Liang Zhang
Keyword(s):  
Numerical Simulation ◽  
Rock Mass ◽  
Strong Support ◽  
Surrounding Rock ◽  
Tunnel Engineering ◽  
Tunnel Excavation ◽  
Rock Stability ◽  
Rock Bolting ◽  
Excavation Support ◽  
The Stability

HuJiaDi tunnel construction of Dai Gong highway is troublesome, the surrounding-rock mass give priority to full to strong weathering basalt, surrounding rock integrity is poor, weak self-stability of surrounding rock, and tunnel is prone to collapse. In order to reduce disturbance, taking advantage of the ability of rock mass, excavation adopt the method of "more steps, short footage and strong support". The excavation method using three steps excavation, The excavation footage is about 1.2 ~ 1.5 m; The surrounding rock bolting system still produce a large deformation after completion of the first support construction, it shows that the adopted support intensity cannot guarantee the stability of the tunnel engineering. Using ABAQUS to simulate tunnel excavation support, optimizing the support parameters of the tunnel, conducting comparative analysis with Monitoring and Measuring and numerical simulation results, it shows that the displacement - time curves have a certain consistency in numerical simulation of ABAQUS and Monitoring and Measuring.

Sign in / Sign up

Export Citation Format

Share Document