scholarly journals Failure Characteristics and Mechanism of Multiface Slopes under Earthquake Load Based on PFC Method

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Tao Yang ◽  
Yunkang Rao ◽  
Huailin Chen ◽  
Bing Yang ◽  
Jiangrong Hou ◽  
...  
Keyword(s):  
Moisture Content ◽  
Failure Mechanism ◽  
Failure Modes ◽  
Shear Failure ◽  
Shaking Table ◽  
Tensile Failure ◽  
Particle Flow Code ◽  
Shear Cracks ◽  
Local Shear ◽  
Shear Slip

Understanding the failure mechanism and failure modes of multiface slopes in the Wenchuan earthquake can provide a scientific guideline for the slope seismic design. In this paper, the two-dimensional particle flow code (PFC2D) and shaking table tests are used to study the failure mechanism of multiface slopes. The results show that the failure modes of slopes with different moisture content are different under seismic loads. The failure modes of slopes with the moisture content of 5%, 8%, and 12% are shattering-shallow slip, tension-shear slip, and shattering-collapse slip, respectively. The failure mechanism of slopes with different water content is different. In the initial stage of vibration, the slope with 5% moisture content produces tensile cracks on the upper surface of the slope; local shear slip occurs at the foot of the slope and develops rapidly; however, a tensile failure finally occurs. In the slope with 8% moisture content, local shear cracks first develop and then are connected into the slip plane, leading to the formation of the unstable slope. A fracture network first forms in the slope with 12% moisture content under the shear action; uneven dislocation then occurs in the slope during vibration; the whole instability failure finally occurs. In the case of low moisture content, the tensile crack plays a leading role in the failure of the slope. But the influence of shear failure becomes greater with the increase of the moisture content.

scholarly journals Failure Behaviour of Sandstone with a Preexisting Joint under Stepped Excavation

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Yinzhu Liu ◽  
Ping Cao ◽  
Liwen He ◽  
Qibin Lin
Keyword(s):  
Failure Modes ◽  
Shear Failure ◽  
Normal Load ◽  
Crack Coalescence ◽  
Tensile Failure ◽  
Type I ◽  
Failure Characteristics ◽  
Excavation Process ◽  
Spalling Failure ◽  
Shear Slip

Much geotechnical construction needs to be carried out under the condition of stepped excavation. However, there is still a lack of research on crack coalescence and failure modes of jointed rock mass under stepped excavation conditions. In order to simulate the stepped excavation test of the real project, the polylactic acid (PLA) material is selected as the filler for the excavation area. The stepped excavation tests are performed on sandstone specimens containing a preexisting joint under different normal load conditions. The dynamic stepped excavation of simulating excavate rock engineering is realised. The constant normal loads during the excavation process are determined to be 80 kN and 100 kN. The influence of the joint inclination on the failure characteristics of the excavation process is analysed. Four typical failure modes are summarised: (a) Mode I: crack coalescence of tensile failure; (b) Mode II: crack coalescence of mixed failure; (c) Mode III: without crack coalescence of mixed failure; (d) Mode IV: without crack coalescence of shear failure. Furthermore, the failure characteristics of the area above the excavation hole and the preexisting joint are analysed. The results show that there are three failure modes: (a) Type I: spalling failure; (b) Type II: shear slip failure; (c) Type III: shear slip and spalling mixed failure.

Study on Failure of Rock Mass around Deep Tunnel

2011 ◽  
Vol 99-100 ◽  
pp. 370-374 ◽  
Author(s):  
Yue Hong Qian ◽  
Ting Ting Cheng ◽  
Xiang Ming Cao ◽  
Chun Ming Song
Keyword(s):  
Rock Mass ◽  
Stress Field ◽  
Failure Modes ◽  
Shear Failure ◽  
Simple Function ◽  
Tensile Failure ◽  
Deep Tunnel ◽  
Main Mode

During excavating the problem of unloading is a dynamic one essentially. Assuming the unloading ruled by a simple function and based on the Hamilton principal, the distribution of the stress field nearby the tunnel is obtained. The characteristics of the failure nearby the tunnel are analyzed considering the shear failure and tensile failure. The results show that the main mode of the shear failure, intact and tensile failure occurs from the tunnel. The characteristic of the shear failure, intact and tensile failure are one of the likely failure modes.

scholarly journals The meso-fracturing mechanism of marble under unloading confining pressure paths and constant axial stress

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Linna Sun ◽  
Liming Zhang ◽  
Yu Cong ◽  
Yaduo Song ◽  
Keqiang He
Keyword(s):  
Shear Failure ◽  
Axial Stress ◽  
Confining Pressure ◽  
Particle Flow Code ◽  
Shear Cracks ◽  
Confining Pressures ◽  
Tension Cracks ◽  
Trial And Error Method ◽  
Unloading Confining Pressure ◽  
Fracturing Mechanism

AbstractFailure tests on marble during unloading confining-pressure under constant axial stress and simulations with the particle flow code were performed. The influence mechanism of the unloading rate of the confining pressure, initial unloading stress, and confining pressure on the failure characteristics of, and crack propagation in, marble was studied. By using the trial-and-error method, the conversion relationship between the unloading rates of confining pressures in laboratory tests and numerical simulations was ascertained. Micro-cracks formed in the unloading process of confining pressure are dominated by tension cracks, accompanied by shear cracks. The propagation of shear cracks lags that of tension cracks. As the confining pressure is increased, more cracks occur upon failure of the samples. The proportion of shear cracks increases while that of tension cracks decreases. The failure mode of samples undergoes a transition from shear-dominated failure to conjugated shear failure.

Tensile behaviors of co-woven-knitted fabric reinforced composites under various strain rates

2011 ◽  
Vol 45 (24) ◽  
pp. 2495-2506 ◽  
Author(s):  
Pibo Ma ◽  
Hong Hu ◽  
Lvtao Zhu ◽  
Baozhong Sun ◽  
Bohong Gu
Keyword(s):  
Strain Rate ◽  
Failure Modes ◽  
Shear Failure ◽  
High Strain ◽  
Tensile Failure ◽  
Knitted Fabric ◽  
Strain Rates ◽  
High Strain Rates ◽  
Textile Composite ◽  
Interface Failure

This article reports the tensile behaviors of a novel kind of 3D textile composite, named as co-woven-knitted fabric (CWKF) reinforced composite, under quasi-static and high strain rates. The tensile tests were conducted along the warp direction (0°), bias direction (45°), and weft direction (90°) at quasi-static strain rate of 0.001/s and high strain rates ranging from 1589/s to 2586/s. The results indicate that the tensile strength, failure strain, tensile stiffness, energy absorption, and resilient energy are strain rate sensitive along all the three directions. The relationships between the mechanical parameters and the strain rate were also analyzed. The fractograph of the CWKF composite demonstrate that the tensile failure modes are matrix shear failure and fibers breakage under the quasi-static testing condition while interface failure and fibers pullout are at high strain rates.

scholarly journals Cracking Behaviors and Mechanical Properties of Rock-Like Specimens with Two Unparallel Flaws under Conventional Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Chenghua Xu ◽  
Liuyang Li ◽  
Yong Liu
Keyword(s):  
Mechanical Properties ◽  
Inclination Angle ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Critical Value ◽  
Tensile Failure ◽  
Rock Bridge ◽  
Bridge Length

Flaws existing in rock masses are generally unparallel and under three-dimensional stress; however, the mechanical and cracking behaviors of the specimens with two unparallel flaws under triaxial compression have been rarely studied. Therefore, this study conducted comprehensive research on the cracking and coalescence behavior and mechanical properties of specimens with two unparallel flaws under triaxial compression. Triaxial compressive tests were conducted under different confining pressures on rock-like specimens with two preexisting flaws but varying flaw geometries (with respect to the inclination angle of the two unparallel flaws, rock bridge length, and rock bridge inclination angle). Six crack types and eleven coalescence types in the bridge region were observed, and three types of failure modes (tensile failure, shear failure, and tensile-shear failure) were observed in experiments. Test results show that bridge length and bridge inclination angle have an effect on the coalescence pattern, but the influence of bridge inclination angle is larger than that of the bridge length. When the confining pressure is low, coalescence patterns and failure modes of the specimens are greatly affected by flaw geometry, but when confining pressure rose to a certain level, the influence of confining pressure is larger than the effect of flaw geometry. The peak strength of the specimens is affected by flaw geometry and confining pressure. There is a critical value for the bridge length. If the bridge length is larger than the critical value, peak strengths of the samples almost keep constant as the bridge length increases. In addition, as the bridge inclination angle increases, there is an increase in the probability of tensile cracks occurring, and with an increase in the confining pressure, the probability of the occurrence of shear cracks increases.

Study on Mechanism of Slope Instability with Weak Interlayer

2011 ◽  
Vol 71-78 ◽  
pp. 3615-3618 ◽  
Author(s):  
Yun Fei Wang ◽  
Fu Ping Zhong ◽  
Huai Bao Chu ◽  
Li Ping Wang
Keyword(s):  
Stress Field ◽  
Failure Mechanism ◽  
Shear Failure ◽  
Slope Instability ◽  
Tensile Failure ◽  
Cyclic Process ◽  
Research Subject ◽  
Geological Conditions ◽  
Weak Interlayer ◽  
Mass Rock

In the process of the highway building, especially in mountain region the some complex geological conditions often appears. In this paper, using the slope of highway with weak interlayer as the research subject, systematically analyzing the stress field and plastic field during the excavation of the slope, obtained the failure mechanism of the slope with weak interlayer, which is a cyclic process that weak interlayer shear failure led to the tensile failure of its upper mass rock. It has extraordinarily important guiding significance for the protection and reinforcement of similar slope.

scholarly journals Effect of Filling Interval Time on Long-Term Mechanical Strength of Layered Cemented Tailing Backfill

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Shuai Cao ◽  
Wei-dong Song
Keyword(s):  
Compressive Strength ◽  
Mechanical Strength ◽  
Failure Modes ◽  
Shear Failure ◽  
Development Stage ◽  
Stability Control ◽  
Tensile Failure ◽  
Uniaxial Compression Test ◽  
Linear Elastic ◽  
Shear Mixing

To explore the influence that filling interval has on the mechanical strength of layered cemented tailing backfill (LCTB), uniaxial compression test is conducted on LCTB samples with a concentration of 70%, 72%, and 75% and a filling interval of 12 h, 24 h, 36 h, and 48 h. From the tests above, mechanical properties and failure modes of LCTB are acquired. The results are as follows: (1) The peak compressive strength of LCTB decreases as the filling interval increases, and it increases when the concentration grows with a certain length of filling interval. At the same time, the peak compressive strength and filling interval show polynomial distribution. (2) There are four stages during the loading process of cemented backfill specimen, that is, compression stage, linear elastic stage, crack extension stage, and undermines development stage. As the filling interval increases, CTB shows a failure mode of tensile failure-tensile shear failure transition-tensile and shear mixing destruction, which provides a theoretical basis for strength design and stability control of backfill.

scholarly journals Experimental Study of the Mechanical Characteristics of a Rock-Like Material Containing a Preexisting Fissure under Loading and Unloading Triaxial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-12 ◽  
Author(s):  
Taoli Xiao ◽  
Mei Huang ◽  
Min Gao
Keyword(s):  
Experimental Study ◽  
Failure Mode ◽  
Mechanical Characteristics ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Tensile Failure ◽  
Underground Engineering ◽  
Inclination Angles ◽  
Loading And Unloading

An experimental study of a rock-like material containing a preexisting fissure subjected to loading and unloading triaxial compression is carried out, and the results show that the mechanical characteristics of the rock-like specimen depend heavily on the loading paths and the inclination of the fissure. The triaxial loading experiment results show that the failure strength linearly increases, while the residual strength linearly decreases with increasing inclination. Furthermore, specimens subjected to triaxial compression show an “X”-type shear failure mode. The triaxial unloading compression experimental results show that specimens with different inclination angles have various failure modes. Specimens with gentle inclinations show a tensile-shear mix failure mode, specimens with middle inclinations show a shear-sliding failure mode, and specimens with steep inclinations show a tensile failure mode. These findings can be used to forecast excavation-induced instabilities in deep underground engineering rock structures.

Effect of Air Position to the Mechanism of Air-Decked Blasting

2011 ◽  
Vol 328-330 ◽  
pp. 1167-1171
Author(s):  
Liang Wu
Keyword(s):  
Failure Mechanism ◽  
Shear Failure ◽  
Near Field ◽  
Blast Hole ◽  
Tensile Failure ◽  
Detonation Waves ◽  
Affecting Factors ◽  
Concrete Damage ◽  
Failure Properties ◽  
The Media

Based on the JHC model of concrete damage evolution, the dynamic stress characteristics and failure mechanism of blast-hole near-field about different air-decked charge structures are studied by numerical simulation. Result shows that the failure mechanism of typical elements changes from compression-shear failure into shear-tensile failure gradually with the increase of their position in indirect initiation of both top-air-decked and bottom-air-decked charges, because of the affecting factors of the freedom and the loading from the hole. If middle-air-decked charges detonate from the top and bottom at the same time, loading and unloading waves in blasting hole are more influential to the damage of bottom elements than the surface freedom, because detonation waves of both top and bottom meet at the middle hole, so it is conducive to the media failure at the bottom hole, the elements of freedom surface have the same failure properties to top-air-decked charge.

scholarly journals Study on stability of filling wall under lateral large-span composite hinge fracture of hard critical block

2021 ◽  
Vol 104 (2) ◽  
pp. 003685042110216
Author(s):  
Chenghai Li ◽  
Yajie Liu ◽  
Jianbiao Bai ◽  
Qing Ge
Keyword(s):  
Field Test ◽  
Shear Failure ◽  
Lateral Displacement ◽  
Axial Stress ◽  
Tensile Failure ◽  
Shear Cracks ◽  
Large Span ◽  
The Stability ◽  
Number Of Segments ◽  
Hinge Fracture

There is still a lack of mature researches on the stability mechanism, influencing factors and control technology of the gob-side filling wall, and systematic researches on the cracking forms and characteristics of the stope roof and the stability of the filling wall are rather insufficient. This paper is aimed at investigating the deformation law of the filling wall under the large-span composite hinge fracture of the hard critical block and solving the difficulty that the large-span critical block lateral fracture poses to gob-side entry retaining. Research methods such as theoretical calculation, mechanical analysis, numerical simulation and field test were adopted comprehensively in this study. When the large-span critical block B is divided into two or three parts, its force on the immediate roof decreases with the increase in the number of segments. Meanwhile, as the number of segments grows, the displacement and axial stress of the filling wall both decrease gradually; the tensile failure weakens relatively, while the shear failure changes slightly. Moreover, both the number of shear cracks and the number of tensile cracks in the filling wall are positively correlated with the strain. When the critical block divided into four parts, the amount of lateral displacement is about 190 mm, and the axial displacement reaches the minimum (about 235 mm). The stability of the filling wall along the gob-side entry is closely related to the lateral fracture span of the stope roof. Under the lateral fracture of the hard critical block, a smaller span of the lateral fracture of the critical block corresponds to a smaller force on the filling wall and a weaker damage to the filling wall. The field test result verifies that cleaving the large-span critical block into smaller segments is conducive to reducing surrounding rock and filling wall deformation.

Sign in / Sign up

Export Citation Format

Share Document