scholarly journals Effect of Filling Interval Time on Long-Term Mechanical Strength of Layered Cemented Tailing Backfill

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Shuai Cao ◽  
Wei-dong Song
Keyword(s):  
Compressive Strength ◽  
Mechanical Strength ◽  
Failure Modes ◽  
Shear Failure ◽  
Development Stage ◽  
Stability Control ◽  
Tensile Failure ◽  
Uniaxial Compression Test ◽  
Linear Elastic ◽  
Shear Mixing

To explore the influence that filling interval has on the mechanical strength of layered cemented tailing backfill (LCTB), uniaxial compression test is conducted on LCTB samples with a concentration of 70%, 72%, and 75% and a filling interval of 12 h, 24 h, 36 h, and 48 h. From the tests above, mechanical properties and failure modes of LCTB are acquired. The results are as follows: (1) The peak compressive strength of LCTB decreases as the filling interval increases, and it increases when the concentration grows with a certain length of filling interval. At the same time, the peak compressive strength and filling interval show polynomial distribution. (2) There are four stages during the loading process of cemented backfill specimen, that is, compression stage, linear elastic stage, crack extension stage, and undermines development stage. As the filling interval increases, CTB shows a failure mode of tensile failure-tensile shear failure transition-tensile and shear mixing destruction, which provides a theoretical basis for strength design and stability control of backfill.

Study on Acoustic Emission and Failure Modes of Rock in Uniaxial Compression Test

2011 ◽  
Vol 261-263 ◽  
pp. 1393-1400
Author(s):  
Ji Liang Zhang ◽  
Chang Hong Li
Keyword(s):  
Compressive Strength ◽  
Acoustic Emission ◽  
Uniaxial Compression ◽  
Compression Test ◽  
Failure Modes ◽  
Soft Rock ◽  
Development Stage ◽  
Uniaxial Compression Test ◽  
Whole Process ◽  
Shear Rupture

Based on uniaxial compression test, the mechanical properties and acoustic emission characteristics of rock had been obtained, including the relationship between AE and time, AE and stress level, and so on, in the whole process of rock failure. Research shows AE rate of rock has the subparagraph features obviously. There are three obvious AE sections for the higher strength elastic-brittle rock: First section is compaction stage, corresponding stress is 10% of compressive strength of rock; Second section is crack-development stage, corresponding stress is 80% of compressive strength; Third section is rupture stage, corresponding stress is the compressive strength. Furthermore, AE signals for the rupture stage is strongest. The law is still correct in cycle loading conditions. However, the subparagraph phenomenon isn’t clear for elastic-plastic rock, and the AE peak is lagging behind the ultimate strength of rock, the AE signal in the decline stage of strength is the most intensive and strong. The lagging phenomenon is due to X-shear rupture model of soft rock. The significant stress concentration in cone tip between the two relative extrusion cones leads to local rock broken seriously. Then, many acoustic signals have been observed.

Study on Failure of Rock Mass around Deep Tunnel

2011 ◽  
Vol 99-100 ◽  
pp. 370-374 ◽  
Author(s):  
Yue Hong Qian ◽  
Ting Ting Cheng ◽  
Xiang Ming Cao ◽  
Chun Ming Song
Keyword(s):  
Rock Mass ◽  
Stress Field ◽  
Failure Modes ◽  
Shear Failure ◽  
Simple Function ◽  
Tensile Failure ◽  
Deep Tunnel ◽  
Main Mode

During excavating the problem of unloading is a dynamic one essentially. Assuming the unloading ruled by a simple function and based on the Hamilton principal, the distribution of the stress field nearby the tunnel is obtained. The characteristics of the failure nearby the tunnel are analyzed considering the shear failure and tensile failure. The results show that the main mode of the shear failure, intact and tensile failure occurs from the tunnel. The characteristic of the shear failure, intact and tensile failure are one of the likely failure modes.

scholarly journals Failure Characteristics and Mechanism of Multiface Slopes under Earthquake Load Based on PFC Method

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Tao Yang ◽  
Yunkang Rao ◽  
Huailin Chen ◽  
Bing Yang ◽  
Jiangrong Hou ◽  
...  
Keyword(s):  
Moisture Content ◽  
Failure Mechanism ◽  
Failure Modes ◽  
Shear Failure ◽  
Shaking Table ◽  
Tensile Failure ◽  
Particle Flow Code ◽  
Shear Cracks ◽  
Local Shear ◽  
Shear Slip

Understanding the failure mechanism and failure modes of multiface slopes in the Wenchuan earthquake can provide a scientific guideline for the slope seismic design. In this paper, the two-dimensional particle flow code (PFC2D) and shaking table tests are used to study the failure mechanism of multiface slopes. The results show that the failure modes of slopes with different moisture content are different under seismic loads. The failure modes of slopes with the moisture content of 5%, 8%, and 12% are shattering-shallow slip, tension-shear slip, and shattering-collapse slip, respectively. The failure mechanism of slopes with different water content is different. In the initial stage of vibration, the slope with 5% moisture content produces tensile cracks on the upper surface of the slope; local shear slip occurs at the foot of the slope and develops rapidly; however, a tensile failure finally occurs. In the slope with 8% moisture content, local shear cracks first develop and then are connected into the slip plane, leading to the formation of the unstable slope. A fracture network first forms in the slope with 12% moisture content under the shear action; uneven dislocation then occurs in the slope during vibration; the whole instability failure finally occurs. In the case of low moisture content, the tensile crack plays a leading role in the failure of the slope. But the influence of shear failure becomes greater with the increase of the moisture content.

Tensile behaviors of co-woven-knitted fabric reinforced composites under various strain rates

2011 ◽  
Vol 45 (24) ◽  
pp. 2495-2506 ◽  
Author(s):  
Pibo Ma ◽  
Hong Hu ◽  
Lvtao Zhu ◽  
Baozhong Sun ◽  
Bohong Gu
Keyword(s):  
Strain Rate ◽  
Failure Modes ◽  
Shear Failure ◽  
High Strain ◽  
Tensile Failure ◽  
Knitted Fabric ◽  
Strain Rates ◽  
High Strain Rates ◽  
Textile Composite ◽  
Interface Failure

This article reports the tensile behaviors of a novel kind of 3D textile composite, named as co-woven-knitted fabric (CWKF) reinforced composite, under quasi-static and high strain rates. The tensile tests were conducted along the warp direction (0°), bias direction (45°), and weft direction (90°) at quasi-static strain rate of 0.001/s and high strain rates ranging from 1589/s to 2586/s. The results indicate that the tensile strength, failure strain, tensile stiffness, energy absorption, and resilient energy are strain rate sensitive along all the three directions. The relationships between the mechanical parameters and the strain rate were also analyzed. The fractograph of the CWKF composite demonstrate that the tensile failure modes are matrix shear failure and fibers breakage under the quasi-static testing condition while interface failure and fibers pullout are at high strain rates.

scholarly journals Cracking Behaviors and Mechanical Properties of Rock-Like Specimens with Two Unparallel Flaws under Conventional Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Chenghua Xu ◽  
Liuyang Li ◽  
Yong Liu
Keyword(s):  
Mechanical Properties ◽  
Inclination Angle ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Critical Value ◽  
Tensile Failure ◽  
Rock Bridge ◽  
Bridge Length

Flaws existing in rock masses are generally unparallel and under three-dimensional stress; however, the mechanical and cracking behaviors of the specimens with two unparallel flaws under triaxial compression have been rarely studied. Therefore, this study conducted comprehensive research on the cracking and coalescence behavior and mechanical properties of specimens with two unparallel flaws under triaxial compression. Triaxial compressive tests were conducted under different confining pressures on rock-like specimens with two preexisting flaws but varying flaw geometries (with respect to the inclination angle of the two unparallel flaws, rock bridge length, and rock bridge inclination angle). Six crack types and eleven coalescence types in the bridge region were observed, and three types of failure modes (tensile failure, shear failure, and tensile-shear failure) were observed in experiments. Test results show that bridge length and bridge inclination angle have an effect on the coalescence pattern, but the influence of bridge inclination angle is larger than that of the bridge length. When the confining pressure is low, coalescence patterns and failure modes of the specimens are greatly affected by flaw geometry, but when confining pressure rose to a certain level, the influence of confining pressure is larger than the effect of flaw geometry. The peak strength of the specimens is affected by flaw geometry and confining pressure. There is a critical value for the bridge length. If the bridge length is larger than the critical value, peak strengths of the samples almost keep constant as the bridge length increases. In addition, as the bridge inclination angle increases, there is an increase in the probability of tensile cracks occurring, and with an increase in the confining pressure, the probability of the occurrence of shear cracks increases.

scholarly journals Experimental Study of the Mechanical Characteristics of a Rock-Like Material Containing a Preexisting Fissure under Loading and Unloading Triaxial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-12 ◽  
Author(s):  
Taoli Xiao ◽  
Mei Huang ◽  
Min Gao
Keyword(s):  
Experimental Study ◽  
Failure Mode ◽  
Mechanical Characteristics ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Tensile Failure ◽  
Underground Engineering ◽  
Inclination Angles ◽  
Loading And Unloading

An experimental study of a rock-like material containing a preexisting fissure subjected to loading and unloading triaxial compression is carried out, and the results show that the mechanical characteristics of the rock-like specimen depend heavily on the loading paths and the inclination of the fissure. The triaxial loading experiment results show that the failure strength linearly increases, while the residual strength linearly decreases with increasing inclination. Furthermore, specimens subjected to triaxial compression show an “X”-type shear failure mode. The triaxial unloading compression experimental results show that specimens with different inclination angles have various failure modes. Specimens with gentle inclinations show a tensile-shear mix failure mode, specimens with middle inclinations show a shear-sliding failure mode, and specimens with steep inclinations show a tensile failure mode. These findings can be used to forecast excavation-induced instabilities in deep underground engineering rock structures.

scholarly journals Failure Behaviour of Sandstone with a Preexisting Joint under Stepped Excavation

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Yinzhu Liu ◽  
Ping Cao ◽  
Liwen He ◽  
Qibin Lin
Keyword(s):  
Failure Modes ◽  
Shear Failure ◽  
Normal Load ◽  
Crack Coalescence ◽  
Tensile Failure ◽  
Type I ◽  
Failure Characteristics ◽  
Excavation Process ◽  
Spalling Failure ◽  
Shear Slip

Much geotechnical construction needs to be carried out under the condition of stepped excavation. However, there is still a lack of research on crack coalescence and failure modes of jointed rock mass under stepped excavation conditions. In order to simulate the stepped excavation test of the real project, the polylactic acid (PLA) material is selected as the filler for the excavation area. The stepped excavation tests are performed on sandstone specimens containing a preexisting joint under different normal load conditions. The dynamic stepped excavation of simulating excavate rock engineering is realised. The constant normal loads during the excavation process are determined to be 80 kN and 100 kN. The influence of the joint inclination on the failure characteristics of the excavation process is analysed. Four typical failure modes are summarised: (a) Mode I: crack coalescence of tensile failure; (b) Mode II: crack coalescence of mixed failure; (c) Mode III: without crack coalescence of mixed failure; (d) Mode IV: without crack coalescence of shear failure. Furthermore, the failure characteristics of the area above the excavation hole and the preexisting joint are analysed. The results show that there are three failure modes: (a) Type I: spalling failure; (b) Type II: shear slip failure; (c) Type III: shear slip and spalling mixed failure.

scholarly journals Effects of Kaolin Addition on Mechanical Properties for Cemented Coal Gangue-Fly Ash Backfill under Uniaxial Loading

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3693
Author(s):  
Faxin Li ◽  
Dawei Yin ◽  
Chun Zhu ◽  
Feng Wang ◽  
Ning Jiang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Uniaxial Compressive Strength ◽  
Shear Failure ◽  
Coal Gangue ◽  
Tensile Failure ◽  
Peak Strain ◽  
Local Shear

In this investigation, six groups of cemented coal gangue-fly ash backfill (CGFB) samples with varying amounts of kaolin (0, 10, 20, 30, 40, and 50%) instead of cement are prepared, and their mechanical properties are analyzed using uniaxial compression, acoustic emission, scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. The uniaxial compressive strength, peak strain, and elastic modulus of CGFB samples decreased with the kaolin content. The average uniaxial compressive strength, elastic modulus, and peak strain of CGFB samples with 10% amount of kaolin are close to that of CGFB samples with no kaolin. The contribution of kaolin hydration to the strength of CGFB sample is lower than that of cement hydration, and the hydration products such as ettringite and calcium-silicate-hydrate gel decrease, thereby reducing strength, which mainly plays a role in filling pores. The contents of kaolin affect the failure characteristics of CGFB samples, which show tensile failure accompanied by local shear failure, and the failure degree increases with the kaolin content. The porosity of the fracture surface shows a decreasing trend as a whole. When the amount of kaolin instead of cement is 10%, the mechanical properties of CGFB samples are slightly different from those of CGFB samples without kaolin, and CGFB can meet the demand of filling strength. The research results provide a theoretical basis for the application of kaolin admixture in fill mining.

scholarly journals Particle Flow Simulation of the Strength and Failure Characteristics of a Layered Composite Rock-Like Sample with a Single Hole

Symmetry ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1132
Author(s):  
Guozhu Wang ◽  
Yu Wang ◽  
Lei Song ◽  
Hao Shi ◽  
Mingwei Zhang ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Failure Mode ◽  
Failure Modes ◽  
Shear Failure ◽  
Surrounding Rock ◽  
Tensile Failure ◽  
Practical Significance ◽  
Rock Masses ◽  
Engineering Structures ◽  
Layered Rock

Layered rock masses with holes are common in nature. Their mechanical behavior plays an important role in the safety and stability of engineering structures. However, previous studies have concentrated on a single lithological layer, and few studies have reported on the mechanical behavior of layered rock masses with holes. Based on the concept of symmetry, uniaxial compression tests and numerical simulations were performed on rock-like specimens with three layers and a hole in the interlayer. The hole was in the center of the sample and was symmetrical up and down. The influence of the thickness and strength of the interlayer on the mechanical behavior and failure processes of the layered rock masses with holes was investigated. The results show that the peak strength and elastic modulus were associated with the thickness and strength of the interlayer. Three failure modes were observed in the specimens, which were not only related to the thickness and strength of the interlayer, but also affected by the presence of the hole. When the thickness of the interlayer is small, mainly a single failure mode was observed (tensile failure or shear failure). However, when the interlayer was thick, the failure mode was tension-shear mixed failure. The failure mechanism of the specimens was primarily crack propagation at the edge of the hole. These research results can provide a basis for site selection, and the design of surrounding rock protection and support parameters, and thus have important practical significance for improving surrounding rock stability and ensuring construction safety.

The effect of elevated temperature on the mechanical properties and failure modes of GFRP face sheets and PET foam cored sandwich beams

2018 ◽  
Vol 22 (4) ◽  
pp. 1235-1255
Author(s):  
Mohsen Rezaei ◽  
Vasileios Karatzas ◽  
Christian Berggreen ◽  
Leif A Carlsson
Keyword(s):  
Compressive Strength ◽  
Polyethylene Terephthalate ◽  
Failure Modes ◽  
Shear Failure ◽  
Elevated Temperatures ◽  
Sandwich Beam ◽  
Standard Test ◽  
Sandwich Beams ◽  
The Face ◽  
Failure Loads

The influence of elevated temperatures on stiffness and strength of composite face sheet and polyethylene terephthalate foam cored sandwich beam has been experimentally investigated. Standard test methods and analytical failure models were used to determine the effect of elevated temperatures. The authors examined E-glass/epoxy cross-ply face laminates, polyethylene terephthalate foam, and sandwich beams consisting of glass/epoxy face laminates and polyethylene terephthalate foam core loaded in four-point flexure. The tensile properties of the face laminate were examined over a temperature range from 25 to 175°C. Compression and shear tests on the face laminate, polyethylene terephthalate foam, and sandwich beams were performed at temperatures up to 100°C. The face laminates exhibited moderate reductions of Young’s modulus and tensile strength, while the compressive strength, shear modulus, and shear strength substantially decreased at elevated temperatures. Similarly, the compressive and shear moduli as well as the compressive strength of the polyethylene terephthalate foam decreased substantially by exposure to a temperature of 100°C. The failure mode of the sandwich panels was observed to be highly dependent on temperature, distinguishing three basic failure modes, viz. core shear failure, indentation failure, and face wrinkling. The failure loads associated to these failure modes were calculated using models available in the literature. The failure loads were found to be consistent with the failure predictions and failure modes.

Sign in / Sign up

Export Citation Format

Share Document