scholarly journals Mechanical Properties and Strength Grading of Engineered Bamboo Composites in China

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Siyuan Tang ◽  
Aiping Zhou ◽  
Jiannan Li
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Structural Engineering ◽  
High Strength ◽  
Distribution Model ◽  
Natural Material ◽  
Structural Applications ◽  
Design Values ◽  
Band Method ◽  
Characteristic Values

Engineered bamboo composite (EBC) is a new high-strength anisotropic structural material, which has standardized sections and less inherent variability than the natural material. For safety reasons in structural applications, the characteristic values of mechanical behaviors are needed to build the design values utilized in practical application. Recent research studies on EBC focused on the mechanical properties from a single source, with little research on the sampling of the manufacturers. The present work investigates mechanical properties of two types of commercially available EBC—parallel strand bamboo (PSB) and laminated veneer bamboo (LVB). The main aim of this work is to evaluate the best probability distribution model (normal, lognormal, and Weibull) and mechanical properties for EBC in China and determine the characteristic values indicated by ASTM D2915. The mechanical properties in tensile, compression, and shear were evaluated using about 4300 small clear specimens from seven manufacturers in five raw bamboo origins of China. Based on the confidence band method, the strength grading of EBC subjected to compressive strength was developed with two predictors (density and MOE). By using intervals of each predictor, several strength grades were built. Each grade has the mean compressive strength, 5th percentile lower value (R0.05), and characteristic value (Rk), which could be used in structural design. This research contributes to the establishment of EBC standards and is essential for further accepting these materials in structural engineering.

scholarly journals Comparison of physical and mechanical properties of river sand concrete with quarry dust concrete

2018 ◽  
Vol 13 (s1) ◽  
pp. 127-134
Author(s):  
Hyginus E. Opara ◽  
Uchechi G. Eziefula ◽  
Bennett I. Eziefula
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
River Sand ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Structural Applications ◽  
Strength Tests ◽  
Quarry Dust

Abstract This study compared the physical and mechanical properties of river sand concrete with quarry dust concrete. The constituent materials were batched by weight. The water-cement ratio and mix ratio selected for the experimental investigation were 0.55 and 1:2:4, respectively. The specimens were cured for 7, 14, 21 and 28 days. Slump, density and compressive strength tests were carried out. The results showed that river sand concrete had greater density and compressive strength than quarry dust concrete for all curing ages. At 28 days of curing, river sand concrete exceeded the target compressive strength by 36%, whereas quarry dust concrete was less than the target compressive strength by 12%. Both river sand concrete and quarry dust concrete for the selected water/cement ratio and mix ratio are suitable for non-structural applications and lightly-loaded members where high strength is not a prerequisite.

UNS A97075

Alloy Digest ◽  
1986 ◽  
Vol 35 (7) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Good Resistance ◽  
Temperature Performance ◽  
Structural Applications ◽  
Structural Parts ◽  
Very High

Abstract UNS No. A97075 is a wrought precipitation-hardenable aluminum alloy. It has excellent mechanical properties, workability and response to heat treatment and refrigeration. Its typical uses comprise aircraft structural parts and other highly stressed structural applications where very high strength and good resistance to corrosion are required. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fatigue. It also includes information on low temperature performance as well as forming, heat treating, and machining. Filing Code: Al-269. Producer or source: Various aluminum companies.

scholarly journals Undergraduate Research Program to Recycle Composite Waste

2021 ◽  
Vol 11 (7) ◽  
pp. 354
Author(s):  
Waleed Ahmed ◽  
Essam Zaneldin ◽  
Amged Al Hassan
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Carbon Fiber ◽  
Undergraduate Students ◽  
Research Program ◽  
Modulus Of Elasticity ◽  
Undergraduate Research ◽  
Undergraduate Research Program ◽  
Structural Applications ◽  
Cfrp Composite

With the rapid growth in the manufacturing industry and increased urbanization, higher amounts of composite material waste are being produced, causing severe threats to the environment. These environmental concerns, coupled with the fact that undergraduate students typically have minimal experience in research, have initiated the need at the UAE University to promote research among undergraduate students, leading to the development of a summer undergraduate research program. In this study, a recycling methodology is presented to test lab-fabricated Carbon-Fiber-Reinforced Polymer (CFRP) for potential applications in industrial composite waste. The work was conducted by two groups of undergraduate students at the UAE University. The methodology involved the chemical dissolution of the composite waste, followed by compression molding and adequate heat treatment for rapid curing of CFRP. Subsequently, the CFRP samples were divided into three groups based on their geometrical distinctions. The mechanical properties (i.e., modulus of elasticity and compressive strength) were determined through material testing, and the results were then compared with steel for prompt reference. The results revealed that the values of mechanical properties range from 2 to 4.3 GPa for the modulus of elasticity and from 203.7 to 301.5 MPa for the compressive strength. These values are considered competitive and optimal, and as such, carbon fiber waste can be used as an alternate material for various structural applications. The inconsistencies in the values are due to discrepancies in the procedure as a result of the lack of specialized equipment for handling CFRP waste material. The study concluded that the properties of CFRP composite prepreg scrap tend to be reusable instead of disposable. Despite the meager experimental discrepancies, test values and mechanical properties indicate that CFRP composite can be successfully used as a material for nonstructural applications.

scholarly journals Development of Novel Lightweight Al-Rich Quinary Medium-Entropy Alloys with High Strength and Ductility

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4223
Author(s):  
Po-Sung Chen ◽  
Yu-Chin Liao ◽  
Yen-Ting Lin ◽  
Pei-Hua Tsai ◽  
Jason S. C. Jang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Compressive Strain ◽  
High Strength ◽  
Fine Tuning ◽  
Face Centered Cubic ◽  
Transportation Industry ◽  
High Entropy ◽  
Good Potential ◽  
Face Centered

Most high-entropy alloys and medium-entropy alloys (MEAs) possess outstanding mechanical properties. In this study, a series of lightweight nonequiatomic Al50–Ti–Cr–Mn–V MEAs with a dual phase were produced through arc melting and drop casting. These cast alloys were composed of body-centered cubic and face-centered cubic phases. The density of all investigated MEAs was less than 5 g/cm3 in order to meet energy and transportation industry requirements. The effect of each element on the microstructure evolution and mechanical properties of these MEAs was investigated. All the MEAs demonstrated outstanding compressive strength, with no fractures observed after a compressive strain of 20%. Following the fine-tuning of the alloy composition, the Al50Ti20Cr10Mn15V5 MEA exhibited the most compressive strength (~1800 MPa) and ductility (~34%). A significant improvement in the mechanical compressive properties was achieved (strength of ~2000 MPa, strain of ~40%) after annealing (at 1000 °C for 0.5 h) and oil-quenching. With its extremely high specific compressive strength (452 MPa·g/cm3) and ductility, the lightweight Al50Ti20Cr10Mn15V5 MEA demonstrates good potential for energy or transportation applications in the future.

scholarly journals Properties of High-Strength Flowable Mortar Reinforced with Palm Fibers

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Test Results ◽  
Palm Fiber ◽  
Toughness Index ◽  
Strength And Toughness

This study was conducted to determine some physical and mechanical properties of high-strength flowable mortar reinforced with different percentages of palm fiber (0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2, 1.4, and 1.6% as volumetric fractions). The density, compressive strength, flexural strength, and toughness index were tested to determine the mechanical properties of this mortar. Test results illustrate that the inclusion of this fiber reduces the density of mortar. The use of 0.6% of palm fiber increases the compressive strength and flexural strength by about 15.1%, and 16%, respectively; besides, the toughness index (I5) of the high-strength flowable mortar has been significantly enhanced by the use of 1% and more of palm fiber.

Deterioration of Mechanical Properties of High-Strength Pumpcrete after Exposure to High Temperatures

2010 ◽  
Vol 168-170 ◽  
pp. 564-569
Author(s):  
Guang Lin Yuan ◽  
Jing Wei Zhang ◽  
Jian Wen Chen ◽  
Dan Yu Zhu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Heating Rate ◽  
High Strength Concrete ◽  
Heating Temperature ◽  
High Strength ◽  
Air Cooling ◽  
Test Results ◽  
Strength Deterioration ◽  
Residual Compressive Strength

This paper makes an experimental study of mechanical properties of high-strength pumpcrete under fire, and the effects of heating rate, heating temperature and cooling mode on the residual compressive strength(RCS) of high-strength pumpcrete are investigated. The results show that under air cooling, the strength deterioration speed of high-strength concrete after high temperature increases with the increase of concrete strength grade. Also, the higher heating temperature is, the lower residual compressive strength value is. At the same heating rate (10°C/min), the residual compressive strength of C45 concrete after water cooling is a little higher than that after air cooling; but the test results are just the opposite for C55 and C65 concrete. The strength deterioration speed of high-strength concrete after high temperature increases with the increase of heating rate, but not in proportion. And when the heating temperature rises up between 200°C and 500°C, heating rate has the most remarkable effect on the residual compressive strength of concrete. These test results provide scientific proofs for further evaluation and analysis of mechanical properties of reinforced-concrete after exposure to high temperatures.

scholarly journals Changing in Fatigue Life of 300 M Bainitic Steel After Laser Carburizing and Plasma Nitriding

2018 ◽  
Vol 165 ◽  
pp. 21002 ◽  
Author(s):  
Antonio J. Abdalla ◽  
Douglas Santos ◽  
Getúlio Vasconcelos ◽  
Vladimir H. Baggio-Scheid ◽  
Deivid F. Silva
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
High Strength ◽  
Tensile Tests ◽  
Steel Sample ◽  
Fatigue Tests ◽  
300M Steel ◽  
Structural Applications

In this work 300M steel samples is used. This high-strength steel is used in aeronautic and aerospace industry and other structural applications. Initially the 300 M steel sample was submitted to a heat treatment to obtain a bainític structure. It was heated at 850 °C for 30 minutes and after that, cooled at 300 °C for 60 minutes. Afterwards two types of surface treatments have been employed: (a) using low-power laser CO2 (125 W) for introducing carbon into the surface and (b) plasma nitriding at a temperature of 500° C for 3 hours. After surface treatment, the metallographic preparation was carried out and the observations with optical and electronic microscopy have been made. The analysis of the coating showed an increase in the hardness of layer formed on the surface, mainly, among the nitriding layers. The mechanical properties were analyzed using tensile and fatigue tests. The results showed that the mechanical properties in tensile tests were strongly affected by the bainitic microstructure. The steel that received the nitriding surface by plasma treatment showed better fatigue behavior. The results are very promising because the layer formed on steel surface, in addition to improving the fatigue life, still improves protection against corrosion and wear.

scholarly journals Effect of Locally Available Wheat Straw Ash in Developing High Strength Concrete

2021 ◽  
pp. 19-28
Author(s):  
Muhammad Armaghan Siffat ◽  
Muhammad Ishfaq ◽  
Afaq Ahmad ◽  
Khalil Ur Rehman ◽  
Fawad Ahmad
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Wheat Straw ◽  
High Strength Concrete ◽  
High Strength ◽  
Optimum Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Strength Concrete ◽  
Straw Ash

This study is supervised to assess the characteristics of the locally available wheat straw ash (WSA) to consume as a substitute to the cement and support in enhancing the mechanical properties of concrete. Initially, after incineration at optimum temperature of 800°C for 0.5, the ash of wheat straw was made up to the desirable level of fineness by passing through it to the several grinding cycles. Subsequently, the X-ray fluorescence (XRF) along with X-ray diffraction (XRD) testing conducted on ash of wheat straw for the evaluation its pozzolanic potential. Finally, the specimens of concrete were made by consuming 10% and 20% percentages of wheat straw ash as a replacement in concrete to conclude its impact on the compressive strength of high strength concrete. The cylinders of steel of dimensions 10cm diameter x 20cm depth were acquired to evaluate the compressive strength of high strength concrete. The relative outcomes of cylinders made of wheat straw ash substitution presented the slight increase in strength values of the concrete. Ultimately, the C-100 blends and WSA aided cement blends were inspected for the rheology of WSA through FTIR spectroscopy along with Thermogravimetric technique. The conclusions authenticate the WSA potential to replace cement in the manufacturing of the high strength concrete.

scholarly journals Strength Characteristics of High Strength Concrete (HSC) with and without Coarse Aggregate

2019 ◽  
Vol 9 (2) ◽  
pp. 4701-4704
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Mechanical Characteristics ◽  
Coarse Aggregate ◽  
High Strength ◽  
Set Up

This paper aimed to investigate the mechanical characteristics of HSC of M60 concrete adding 25% of fly ash to cement and sand and percentage variations of silica fumes 0%,5% and 10% to cement with varying sizes of 10mm,6mm,2mm and powder of granite aggregate with w/c of 0.32. Specimens are tested for compressive strength using 10cm X 10cmX10cm cubes for 7,14,28 days flexural strength was determined by using 10cmX10cmX50cm beam specimens at 28 days and 15cm diameter and 30cm height cylinder specimens at 28 days using super plasticizers of conplast 430 as a water reducing agent. In this paper the experimental set up is made to study the mechanical properties of HSC with and without coarse aggregate with varying sizes as 10mm, 6mm, 2mm and powder. Similarly, the effect of silica fume on HSC by varying its percentages as 0%, 5% and 10% in the mix studied. For all mixes 25% extra fly ash has been added for cement and sand.

scholarly journals Effect of basalt fibres on the parameters of fracture mechanics of MB modifier based high-strength concrete

2018 ◽  
Vol 251 ◽  
pp. 02003 ◽  
Author(s):  
Makhmud Kharun ◽  
Dmitry Koroteev
Keyword(s):  
Compressive Strength ◽  
Fracture Mechanics ◽  
High Strength Concrete ◽  
High Strength ◽  
Critical Energy ◽  
Critical Stress Intensity Factor ◽  
Critical Energy Release Rate ◽  
Environmental Friendliness ◽  
Strength Concrete ◽  
Structural Applications

Basalt fibres (BF) are increasingly studied in structural applications due to its environmental friendliness and good mechanical properties. Mass production of high-strength concrete (HSC) in Russia is mainly associated with the use of organomineral modifiers of the MB series, containing in their composition microsilica, fly ash, hardening regulator and superplasticizer C-3 in different ratios. In our study we produced HSC specimens (without BF, and with 1 wt.% chopped BF) using the modifier MB10-30, with the dimensions of 100x100x100 mm, 100x100x400 mm, 100x100x400 mm with the artificial crack of 25 mm deep in the middle of the span, and also 100х75х400 mm (75 mm height was taken equal to the height of the section above the crack of the 2nd type of prisms). The compressive strength, the tensile strength at bending, the strength at axial tension, the cracking moment, and also the parameters of fracture mechanics, such as: the critical stress intensity factor and the critical energy release rate, at the curing periods of 7, 14, 28, 60 days, have been determined. We also evaluated the influence of crack in the bend element on the value of the cracking moment. The results showed that the inclusion of BF in MB modifier based HSC resulted in a decrease in the compressive strength, however, significantly enhanced its flexure behavior.

Sign in / Sign up

Export Citation Format

Share Document