scholarly journals Corrosion and Hardness Behaviour of Al/GO Nanocomposites Processed by the Ultrasonic Gravitational Stir Casting Method

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
S. Narayanan ◽  
G. G. Sozhamannan ◽  
K. Hemalatha ◽  
K. Velmurugan ◽  
V. S. K. Venkatachalapathy
Keyword(s):  
Metal Matrix ◽  
Immersion Time ◽  
Corrosion Behaviour ◽  
Casting Process ◽  
Stir Casting ◽  
Matrix Composites ◽  
Casting Method ◽  
Weight Losses ◽  
Immersion Corrosion ◽  
Time Periods

The objective of this work is to evaluate the corrosion behaviour of nanographene oxide reinforced aluminium (Al/GO) metal matrix composites with different immersion time periods using the immersion corrosion technique. The Al/GO composites were fabricated by the ultrasonic gravitational stir casting process. The corrosions of Al/GO were evaluated using a scanning electron microscope. The experimental results revealed that the corrosion rate decreased and weight losses increased with increasing immersion time periods. The nonimmersed Al/GO composites exhibited higher microhardness values compared to the immersed Al/GO composites.

scholarly journals CORROSION BEHAVIOUR OF ALUMINIUM 6061 NICKEL COATED CENOSPHERE COMPOSITE

2020 ◽  
Vol 15 (3) ◽  
Author(s):  
Arvind R S ◽  
Prasanna Ram M ◽  
Prashanth T ◽  
Jaimon Dennis Quadros
Keyword(s):  
Coal Combustion ◽  
Metal Matrix ◽  
Power Plants ◽  
Corrosion Behaviour ◽  
Thermal Power ◽  
Stir Casting ◽  
Matrix Composites ◽  
Test Results ◽  
Immersion Corrosion ◽  
Aluminium Metal

Cenosphere fly ash is one of the most inexpensive and low-density material which is abundantly available as a solid waste by-product of coal combustion in thermal power plants. Aluminium metal matrix composites with Nickel coated cenospheres as the reinforcement is prepared by stir casting route. The composites are prepared with varying percentages of cenospheres in the percentage of 2-10% by weight of the composite. Immersion corrosion tests are conducted on the composites in three different medium and for three different time durations. It is evident from the test results as well as the microstructure images that the weight loss of samples with 8% Nickel coated cenospheres has shown least corrosion or the highest corrosion resistance when compared to the counterparts.

scholarly journals Properties of AlSi9Cu3 metal matrix micro and nano composites produced via stir casting

2018 ◽  
Vol 16 (1) ◽  
pp. 726-731 ◽  
Author(s):  
Tennur Gülşen Ünal ◽  
Ege Anıl Diler
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix ◽  
Weight Fraction ◽  
Stir Casting ◽  
Mechanical Tests ◽  
Matrix Composites ◽  
Casting Method ◽  
Porosity Formation ◽  
Three Point Bending ◽  
Hardness Values

AbstractThe effects of micro and nano sized reinforcement particles on microstructure and mechanical properties of aluminium alloy-based metal matrix composites were investigated in this study. AlSi9Cu3 alloy was reinforced with micro and nano sized ceramic reinforcement particles at different weight fractions by using a stir casting method. The mechanical tests (hardness, three point bending) were performed to determine the mechanical properties of AlSi9Cu3 alloy-based microcomposites (AMMCs) and nanocomposites (AMMNCs). The experimental results have shown that the size and weight fraction of reinforcement particles have a strong influence on the microstructure and the mechanical properties of AlSi9Cu3 alloy-based microcomposites and nanocomposites. The relative densities of all AMMC and AMMNC samples are lower than unreinforced AlSi9Cu3 alloy due to porosity formation with the increase of weight fraction of reinforcement particles. As weight fraction increases, hardness values of AMMCs and AMMNCs increase. Maximum flexural strength can be obtained at 3.5wt.% for the AMMC sample with microsized Al2O3 particles and at 2wt.% for the AMMNC sample with nano-sized Al2O3 particles. After the weight fractions exceed these values, flexural strengths of both AMMCs and AMMNCs decrease due to clustering of Al2O3 particles.

Production of Al Metal Matrix Composites by the Stir-Casting Method

2013 ◽  
Vol 592-593 ◽  
pp. 614-617 ◽  
Author(s):  
Konstantinos Anthymidis ◽  
Kostas David ◽  
Pavlos Agrianidis ◽  
Afroditi Trakali
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Automobile Industry ◽  
Metal Matrix ◽  
Aluminum Matrix ◽  
Stir Casting ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Casting Method ◽  
Alloy Matrix

It is well known that the addition of ceramic phases in an alloy e.g. aluminum, in form of fibers or particles influences its mechanical properties. This leads to a new generation of materials, which are called metal matrix composites (MMCs). They have found a lot of application during the last twenty-five years due to their low density, high strength and toughness, good fatigue and wear resistance. Aluminum matrix composites reinforced by ceramic particles are well known for their good thermophysical and mechanical properties. As a result, during the last years, there has been a considerable interest in using aluminum metal matrix composites in the automobile industry. Automobile industry use aluminum alloy matrix composites reinforced with SiC or Al2O3 particles for the production of pistons, brake rotors, calipers and liners. However, no reference could be cited in the international literature concerning aluminum reinforced with TiB particles and Fe and Cr, although these composites are very promising for improving the mechanical properties of this metal without significantly alter its corrosion behavior. Several processing techniques have been developed for the production of reinforced aluminum alloys. This paper is concerned with the study of TiB, Fe and Cr reinforced aluminum produced by the stir-casting method.

Production of Metal Matrix Composite Using a Bottom Tapping Stir Casting Furnace

2015 ◽  
Vol 772 ◽  
pp. 263-267 ◽  
Author(s):  
Ramanathan Arunachalam ◽  
Majid Al-Maharbi ◽  
Yahya Al Kiyumi ◽  
Elyas Aal-Thani ◽  
Mohammed Al Mafraji
Keyword(s):  
Continuous Improvement ◽  
Manufacturing Process ◽  
Metal Matrix ◽  
Low Cost ◽  
Casting Process ◽  
Stir Casting ◽  
Matrix Composites ◽  
High Quality ◽  
Reinforcement Material ◽  
Low Cost Manufacturing

Metal matrix composites (MMC's) have attracted the attention of researchers for quite some time. In the last 15 years, many studies have been reported in this field of MMC production through various routes. The most commonly used process for producing MMC is stir casting process whereby the reinforcement material is incorporated into the molten metal by stirring. It is a relatively low cost manufacturing process that is capable of producing high quality MMC. However, the process is associated with issues such as attaining uniform distribution of particles, wettability between particles and porosity in the MMCs. Because of these challenges, there has been continuous improvement in the process as well as the design of the furnace. In this research, an innovatively designed bottom tapping furnace has been used to produce the MMCs and the produced sample is characterized.

Experimental Investigation of Alumina Reinforced Copper Metal Matrix Composite by Stir Casting Method

2019 ◽  
Vol 11 (1) ◽  
Author(s):  
M. Palanivendhan ◽  
J. Chandradass ◽  
Ajith Rajendran ◽  
Nishanth M. Govindarajan ◽  
M. Adwait Krishnaa
Keyword(s):  
Thermal Conductivity ◽  
Metal Matrix ◽  
Weight Ratio ◽  
Copper Matrix ◽  
Stir Casting ◽  
Mechanical Tests ◽  
Matrix Composites ◽  
Copper Metal ◽  
Casting Method ◽  
Combined Loads

In the present study, alumina reinforced copper metal matrix composites were prepared by stir casting method. Three different specimens were prepared by changing the weight ratio of alumina to copper. The samples were prepared by adding 10%, 20% and 30% alumina to copper matrix. The three specimens were subjected to mechanical, thermal and corrosion testing, in order to find out the properties of the material. Various mechanical tests like hardness, impact and corrosion were performed including thermal conductivity to understand the behaviour of the specimens under combined loads. Specimen number 2 which was 80%-20% copper to alumina was found to be the best combination for such type of applications.

Microstructure and Properties of Stir Cast AZ91 Mg Alloy – SiCp Composites

2012 ◽  
Vol 710 ◽  
pp. 365-370 ◽  
Author(s):  
Sujayakumar Prasanth ◽  
Kumaraswamy Kaliamma Ajith Kumar ◽  
Thazhavilai Ponnu Deva Rajan ◽  
Uma Thanu Subramonia Pillai ◽  
Bellambettu Chandrasekhara Pai
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Microstructural Characterization ◽  
Casting Process ◽  
Stir Casting ◽  
Tensile Fracture ◽  
Matrix Composites ◽  
Az91 Magnesium Alloy ◽  
The Matrix ◽  
Az91 Magnesium

Magnesium metal matrix composites (MMCs) have been receiving attention in recent years as an attractive choice for aerospace and automotive applications because of their low density and superior specific properties. Using stir casting process, AZ91 magnesium alloy metal matrix composites have been produced with different weight percentages (5, 10, 15, 20 and 25) of silicon carbide particles (SiCp) addition. Microstructural characterization reveals uniform distribution of SiC particles with good interfacial bonding between the matrix and reinforcement. Electrical conductivity and Co-efficient of Thermal Expansion (CTE) measurements carried out on these composites have yielded better properties. Improved mechanical properties such as hardness, ultimate tensile strength, and compressive strength are obtained. The microfracture mechanisms involved during tensile fracture is analyzed and correlated with the properties obtained.

Sign in / Sign up

Export Citation Format

Share Document