scholarly journals Numerical Investigation of Bundled RC Column under Impact Load

2021 ◽  
Vol 2021 ◽  
pp. 1-18
Author(s):  
Abreha Abay ◽  
Temesgen Wondimu
Keyword(s):  
Reinforced Concrete ◽  
Impact Velocity ◽  
Axial Load ◽  
Impact Load ◽  
Lateral Impact ◽  
Reinforced Concrete Column ◽  
Rc Columns ◽  
Rc Column ◽  
The Impact ◽  
Reinforcement Distribution

Dynamic impact load has an extensive application area in civil engineering, including highway, military, and marine structures. Many researchers have studied the performance of reinforced concrete (RC) columns under impact load. However, very limited work has been conducted on the effect of bundle reinforced concrete (BRC) columns subjected to lateral impact load. In this study, to examine the behavior of RC columns under impact load, numerical simulations of one with normal reinforcement distribution and three different bundles of reinforced concrete column specimens have been conducted using an explicit finite element (FE) analysis. In addition to the bundle reinforcement distribution, the parameters considered in the study are impact scenarios, impact velocity, pure axial load, and impact locations. From the numerical analysis, it has been found that bundling of longitudinal reinforcement does not only improve the impact capacity but also stabilizes the fluctuating response of impacted reinforced concrete columns. Both peak impact force and maximum lateral displacements of impacted BRC columns increase with increasing initial impact velocity. The numerical results also show that pure axial load slightly improved the impact capacity of the BRC columns. Finally, while the global failure of the RC column governs the response of repeatedly impacted BRC columns, failure characteristics of the single impacted columns are associated with local concrete damage at the impact zone.

Short reinforced concrete column capacity under biaxial bending and axial load

2000 ◽  
Vol 27 (6) ◽  
pp. 1173-1182 ◽  
Author(s):  
H P Hong
Keyword(s):  
Reinforced Concrete ◽  
Probabilistic Analysis ◽  
Axial Load ◽  
Failure Surface ◽  
Biaxial Bending ◽  
Reinforced Concrete Column ◽  
Rc Columns ◽  
Nonlinear Stress ◽  
Modeling Errors ◽  
Error Optimization

The paper describes the development of a simple theoretical approach in estimating the capacity of short reinforced concrete (RC) columns under biaxial bending and axial load. The developed approach considers the nonlinear stress-strain relations of concrete and reinforcing steel and does not make the assumption about the limiting strain of extreme compression fiber of concrete. The solution is obtained using a nonlinearly constrained optimization algorithm. The approach was used to estimate the theoretical capacities of many tested RC columns found in the literature. A probabilistic analysis of the modeling errors was carried out using the ratios of the test-to-predicted results. The probabilistic analysis was extended to include two simplified theoretical methods: the reciprocal load method given by Bresler and the failure surface method given by Hsu.Key words: biaxial bending, modeling error, optimization, probability distribution.

The effect of assembling location on the performance of precast concrete beam under impact load

2017 ◽  
Vol 21 (8) ◽  
pp. 1211-1222 ◽  
Author(s):  
Qiushi Yan ◽  
Bowen Sun ◽  
Xuemei Liu ◽  
Jun Wu
Keyword(s):  
Reinforced Concrete ◽  
Impact Velocity ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Impact Load ◽  
Precast Concrete ◽  
Reinforced Concrete Beams ◽  
Impact Location ◽  
Weight Impact ◽  
The Impact

With incorporation of assembling joints, precast concrete beams could behave very differently in resisting both static and dynamic loads in comparison to conventional reinforced concrete beams. With no research available on the dynamic behavior of precast concrete beams under impact load, a combined experimental and numerical study is conducted to investigate the dynamic response of precast concrete beams under impact load. The results were also compared with reinforced concrete beams. Four groups of concrete beams were tested with all beams designed with the same reinforcement, but different assembling locations were considered for precast concrete beams. The effects of the assembling location in resisting drop weight impact of precast concrete beams were analyzed. The influence of impact mass and impact velocity on the impact resistance of precast concrete beams were also investigated. The results revealed that the further the assembling location is away from the impact location, the closer the mechanical performance of the precast concrete beam is to that of the reinforced concrete beam. When the assembling location and the impact location coincided, the assembling region suffered from severe local damages. With increased impact velocity and impact energy, the damage mode of the precast concrete beams may change gradually from bending failure to bending–shear failure and eventually to local failure. In addition, the bonding around the assembling interface was found to be effective to resist drop weight impact load regardless of the magnitude of the impact velocity and energy.

Dynamic Response Analysis of the T-Shaped Steel Reinforced Concrete Column under Different Impact Conditions

2013 ◽  
Vol 351-352 ◽  
pp. 663-666
Author(s):  
Shou Yan Bai ◽  
Jing Jiang ◽  
Ya Feng Xu
Keyword(s):  
Reinforced Concrete ◽  
Dynamic Response ◽  
Response Analysis ◽  
Concrete Column ◽  
Lateral Impact ◽  
Reinforced Concrete Column ◽  
Impact Site ◽  
Steel Reinforced Concrete ◽  
Finite Element Software ◽  
The Impact

This paper simulated the resistance to lateral impact properties of the T-shaped steel reinforced concrete column through the large finite element software ABAQUS. Extracting the time-displacement curves of different impact sites, by comparison we know: with the impact site is farther and farther from solid end, the maximum lateral displacement in the impact site of the member is bigger and bigger. The maximum displacements in the symmetrical place to the mid-span of the member are very similar. From time-displacement curves of seven models we can know, after reaching the ultimate bearing capacity, the curves leveled off gradually and changed slowly showing good stability and showing good ductility and deformation capacity. It can be concluded: the impact different parts of the dynamic response of lateral impact of the T-shaped steel reinforced concrete columns have a certain impact.

scholarly journals Numerical Assessment of Reinforced Concrete Beams Strengthened with CFRP Sheets under Impact Loading

2021 ◽  
Vol 15 (58) ◽  
pp. 48-64
Author(s):  
Mohamed Emara ◽  
Nada Elkomy ◽  
Hilal Abdel Kader
Keyword(s):  
Reinforced Concrete ◽  
Impact Velocity ◽  
Impact Loading ◽  
Impact Load ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymers ◽  
Rc Beams ◽  
Cfrp Sheets ◽  
Externally Bonded ◽  
The Impact

This paper investigates numerically the behavior of Reinforced Concrete (RC) beams, strengthened using Carbon Fiber Reinforced Polymers (CFRP) sheets, subjected to impact loading. Three-dimensional finite element analysis was performed and its results were verified against experimental ones available in the literature showing good agreement. Then, a comprehensive parametric study was performed to investigate the effect of studied parameters on the strengthened RC beams. The main studied parameters were type and size of reinforcing bars, geometric characteristics of externally bonded CFRP sheets (width, length, and thickness), impact velocity, and the position of the impactor with respect to the beam. Results showed that the use of externally bonded CFRP sheets enhanced the beam capacity and failure mode, and reduced the mid-span deflection. Moreover, a reduction in the mid-span deflection was observed due to the use of CFRP bars as internal reinforcement. On the other hand, the deflection was increased due to the increase of the impact velocity, and the change of the impact load position.

Impact Response of Reinforced Concrete Columns with Different Axial Load under Low-Velocity Impact Loading

2019 ◽  
Vol 803 ◽  
pp. 322-330
Author(s):  
Warakorn Tantrapongsaton ◽  
Chayanon Hansapinyo
Keyword(s):  
Reinforced Concrete ◽  
Axial Load ◽  
Impact Load ◽  
Concrete Columns ◽  
Shear Capacity ◽  
Low Velocity Impact ◽  
Shear Cracks ◽  
Reinforced Concrete Columns ◽  
Impact Responses ◽  
The Impact

Building collapses from the seismic pounding of two adjacent buildings have been found in many past earthquakes. For the two buildings with different story height, the pounding induces impact load and local stress at column mid-height where the provided column reinforcement is normally lesser than the column’s edge. This paper aims to investigate the impact responses of reinforced concrete columns with different axial load and shear capacity by using numerical simulation method. Sixteen reinforced concretes columns were subjected to an impact load created by dropping 300 kg hammer at the height of 1,200 mm above the mid-span of the column. Every specimen has an identical cross section of 220 mm by 220 mm, with 3,000 mm of clear span length. Both ends of the column were fully restrained. The magnitude of the axial load varies from 0% to 40% of the ultimate axial capacity of the concrete section. Shear reinforcement spacing varies from @200 mm to @60 mm. It is found that the axial loads have a great effect on the impact responses of the RC columns. The specimens with high axial load yield higher peak impact force value and less mid-span deflection. Shear cracks were observed on the specimens with low axial force, but the cracks were relatively decreased when increasing the axial load.

Parametric Analysis of the Dynamic Response of Hot-Rolled H-Shaped Steel Beam under Lateral Impact Load

2012 ◽  
Vol 215-216 ◽  
pp. 998-1002 ◽  
Author(s):  
Chang Pei ◽  
Rui Wang
Keyword(s):  
Dynamic Response ◽  
Impact Velocity ◽  
Impact Energy ◽  
Impact Load ◽  
Steel Beam ◽  
Lateral Impact ◽  
Analysis Model ◽  
Fea Model ◽  
Hot Rolled ◽  
The Impact

The analysis on the basic mechanical properties of hot-rolled H-shaped steel beam under lateral impact load was done by use of ABAQUS. The reliability of the FEA model was verified through comparing with the existing experiment of H-shaped steel beam subjected to lateral impact. And then, this FEA model was used to research the dynamic response of the H-shaped steel beam subjected to lateral impact. The main parameters include the impact energy, mass and impact velocity of the impact hammer. The results indicate that the finite element analysis model built in this paper could accurately simulate the process of hot-rolled H-shaped steel beam under lateral impact load and the impact energy, mass and impact velocity have different influences on the dynamic response of H-shaped steel beam.

Lateral Impact Response of Elliptical Hollow and Partially Concrete-Filled Cold-Formed Steel Columns Under Static Axial Compression Load

2021 ◽  
Author(s):  
Nayyer Mohammadi Rana ◽  
Elham Ghandi ◽  
Shirin Esmaeili Niari
Keyword(s):  
Impact Velocity ◽  
Impact Load ◽  
Impact Resistance ◽  
Compressive Load ◽  
Lateral Impact ◽  
Elliptical Cross ◽  
Compression Load ◽  
Steel Columns ◽  
Size And Shape ◽  
The Impact

In recent years, the use of partially concrete-filled steel tubular (PCFST) columns has been considered due to their cost-effectiveness and reduction of structural weight in bridge piers and building columns. One of the critical discussions about these columns is their impact resistance. In this article, the dynamic response of hollow and PCFST columns with elliptical cross-section under simultaneous loading of static axial compressive load and lateral impact load is presented using finite element modeling in ABAQUS software (FEA). To ensure the accuracy of the numerical modeling, the analysis results are compared with the results of previous works. The effects of different parameters such as impact velocity, the height of the impact location, the impact direction, the impact block mass, the size and shape of the impact block are investigated in this paper. The results of the numerical analysis showed that the partially filled specimens had better performance than the hollow specimens. The changes in impact direction and impact block mass parameters have a significant effect on the failure of the columns, especially when they are under high impact velocity. Changing the impact velocity significantly affects the impact resistance of specimens. However, the size and shape of the impact block did not have a significant effect on the displacement of the column against the impact loading.

Experimental Studies of Reinforced Concrete Column Capacity Affected by Core Drilling

2010 ◽  
Vol 133-134 ◽  
pp. 1195-1200 ◽  
Author(s):  
Lei Zhu ◽  
Qing Feng Xu ◽  
Xiang Min Li ◽  
Chun Ming Zhu
Keyword(s):  
Reinforced Concrete ◽  
Axial Compression ◽  
Experimental Studies ◽  
Concrete Column ◽  
Reinforced Concrete Column ◽  
Rc Columns ◽  
Core Drilling ◽  
Rc Column ◽  
Compression Failure ◽  
Short Columns

The paper presents the experimental studies of reinforced concrete column (RC column) capacity affected by core drilling. By testing three groups (9 total) of full scale concrete short columns, the experiment demonstrates that the axial compression capacity of RC columns after core drilling is reduced from 5.63% to 22.14% while the ultimate displacement decreases from 1.88% to 26.14%. The behavior of columns is altered from the axial compression failure to a small-eccentricity compression failure. The paper summarizes experiment results, followed by an investigation of the dominant factors, such as column effective cross section, drilling location, drilled hole repairing and reinforcing steels discontinued by drilling, that have impact on RC column capacity. The rationale of capacity variations of RC columns due to core drilling is also investigated.

scholarly journals Experimental Research on Reinforced Concrete Columns Strengthened with Steel Jacket and Concrete Infill

2021 ◽  
Vol 11 (9) ◽  
pp. 4043
Author(s):  
Aleksandar Landović ◽  
Miroslav Bešević
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Cross Section ◽  
Experimental Research ◽  
Failure Modes ◽  
Steel Tube ◽  
Rc Columns ◽  
Rc Column ◽  
Steel Jacket ◽  
Ductile Behavior

Experimental research on axially compressed columns made from reinforced concrete (RC) and RC columns strengthened with a steel jacket and additional fill concrete is presented in this paper. A premade squared cross-section RC column was placed inside a steel tube, and then the space between the column and the tube was filled with additional concrete. A total of fourteen stub axially compressed columns, including nine strengthened specimens and five plain reinforced concrete specimens, were experimentally tested. The main parameter that was varied in the experiment was the compressive strength of the filler concrete. Three different concrete compression strength classes were used. Test results showed that all three cross-section parts (the core column, the fill, and the steel jacket) worked together in the force-carrying process through all load levels, even if only the basic RC column was loaded. The strengthened columns exhibited pronounced ductile behavior compared to the plain RC columns. The influence of the test parameters on the axial compressive strength was investigated. In addition, the specimen failure modes, strain development, and load vs. deformation relations were registered. The applicability of three different design codes to predict the axial bearing capacity of the strengthened columns was also investigated.

Sign in / Sign up

Export Citation Format

Share Document