scholarly journals Analysis of Interwell Connectivity of Tracer Monitoring in Carbonate Fracture-Vuggy Reservoir: Taking T-Well Group of Tahe Oilfield as an Example

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Shuyao Sheng ◽  
Yonggang Duan ◽  
Mingqiang Wei ◽  
Tao Yue ◽  
Zijian Wu ◽  
...  
Keyword(s):  
Oil And Gas ◽  
Water Movement ◽  
Flow Simulation ◽  
Concentration Curve ◽  
Physical Parameters ◽  
Tracer Concentration ◽  
Channel Diameter ◽  
Oil And Gas Exploration ◽  
Tahe Oilfield ◽  
Production Wells

Carbonate fracture-vuggy reservoirs are one of the hot spots in oil and gas exploration and development. However, it is extremely difficult to describe the internal spatial structure of the fracture-vuggy unit and understand the interwell connection relationship. As a method to measure reservoir characteristics and feedback reservoir production information directly according to the detected concentration curve, interwell tracer technology provides a direct measure for people to understand the law of oil-water movement and reservoir heterogeneity and is widely used in various domestic oil fields. Based on the flow law of tracer and the CFD flow simulation basic model, this paper establishes the physical conceptual model and studies the influence of three physical parameters (the flow velocity of the fluid passing through the connected channel, diameter of the connected channel, and length of the connected channel) on the concentration curve at the outlet. In addition, the influence of different interwell connection modes on tracer concentration was studied and classified scientifically. According to the simulation, the tracer concentration curve can be classified into three types: unimodal curve, bimodal curve, and multimodal curve. Finally, the injection-production well group in the T-well area of the Tahe Oilfield is taken as an example, the connection mode between injection and production wells in this well area is further discussed and has been verified, which can be used as a reference for the connectivity analysis of similar carbonate reservoirs.

Upscaling for Compositional Reservoir Simulation

SPE Journal ◽  
2016 ◽  
Vol 21 (03) ◽  
pp. 0873-0887 ◽  
Author(s):  
Hangyu Li ◽  
Louis J. Durlofsky
Keyword(s):  
Oil Recovery ◽  
Oil And Gas ◽  
Flow Simulation ◽  
Compositional Simulation ◽  
Coarse Scale ◽  
Gas Phases ◽  
Compositional Flow ◽  
Production Wells ◽  
Computational Procedures ◽  
Coarse Model

Summary Compositional flow simulation, which is required for modeling enhanced-oil-recovery (EOR) operations, can be very expensive computationally, particularly when the geological model is highly resolved. It is therefore difficult to apply computational procedures that require large numbers of flow simulations, such as optimization, for EOR processes. In this paper, we develop an accurate and robust upscaling procedure for oil/gas compositional flow simulation. The method requires a global fine-scale compositional simulation, from which we compute the required upscaled parameters and functions associated with each coarse-scale interface or wellblock. These include coarse-scale transmissibilities, upscaled relative permeability functions, and so-called α-factors, which act to capture component flow rates in the oil and gas phases. Specialized near-well treatments for both injection and production wells are introduced. An iterative procedure for optimizing the α-factors is incorporated to further improve coarse-model accuracy. The upscaling methodology is applied to two example cases, a 2D model with eight components and a 3D model with four components, with flow in both cases driven by wells arranged in a five-spot pattern. Numerical results demonstrate that the global compositional upscaling procedure consistently provides very accurate coarse results for both phase and component production rates, at both the field and well level. The robustness of the compositionally upscaled models is assessed by simulating cases with time-varying well bottomhole pressures that are significantly different from those used when the coarse model was constructed. The coarse models are shown to provide accurate predictions in these tests, indicating that the upscaled model is robust with respect to well settings. This suggests that one can use upscaled models generated from our procedure to mitigate computational demands in important applications such as well-control optimization.

Spatial Variability of Physical Parameters and Processes in Two Field Soils

1991 ◽  
Vol 22 (5) ◽  
pp. 327-340 ◽  
Author(s):  
K. Høgh Jensen ◽  
J. C. Refsgaard
Keyword(s):  
Transport Model ◽  
Flow Direction ◽  
Measurement Data ◽  
Flow Simulation ◽  
Solute Concentration ◽  
Conclusive Evidence ◽  
Physical Parameters ◽  
Effective Parameters ◽  
The Mean ◽  
Tracer Experiments

A numerical analysis of solute transport in two spatially heterogeneous fields is carried out assuming that the fields are composed of ensembles of one-dimensional non-interacting soil columns, each column representing a possible soil profile in statistical terms. The basis for the analysis is the flow simulation described in Part II (Jensen and Refsgaard, this issue), which serves as input to a transport model based on the convection-dispersion equation. The simulations of the average and variation in solute concentration in planes perpendicular to the flow direction are compared to measurements obtained from tracer experiments carried out at the two fields. Due to the limited amount of measurement data, it is difficult to draw conclusive evidence of the simulations, but reliable simulations are obtained of the mean behaviour within the two fields. The concept of equivalent soil properties is also tested for the transport problem in heterogeneous soils. Based on effective parameters for the retention and hydraulic conductivity functions it is possible to predict the mean transport in the two experimental fields.

Control System Design of the Vehicle Mounted Hammer Source Based on PLC

2012 ◽  
Vol 619 ◽  
pp. 302-305
Author(s):  
Hong Yan Wang ◽  
Wen Sheng Xiao ◽  
Xiu Juan Lin ◽  
Xian Feng Wang
Keyword(s):  
Control System ◽  
System Design ◽  
Software Design ◽  
High Velocity ◽  
Simple Structure ◽  
Oil And Gas ◽  
Basic Structure ◽  
Control System Design ◽  
Oil And Gas Exploration ◽  
Gas Consumption

Considering the pollution on the environment using dynamite source in oil and gas exploration, harm and damage to people and building, the vehicle mounted hammer source which can replace dynamite source is presented. This paper describes briefly the basic structure and working principles of the vehicle mounted hammer source. A typical pneumatic circuit is researched and designed. And the pneumatic circuit is designed with the powerful functions of PLC, the hardware and software design are introduced. The system has advantages of strong striking force, high velocity, small gas consumption, simple structure and convenient control.

Accelerating oil and gas investment and reserves by design

2018 ◽  
Vol 58 (2) ◽  
pp. 557
Author(s):  
Barry A. Goldstein
Keyword(s):  
Natural Gas ◽  
Fossil Fuels ◽  
Oil And Gas ◽  
South Australia ◽  
Land Access ◽  
Oil And Gas Exploration ◽  
Oil And Gas Producers ◽  
Crude Oil Prices ◽  
Exploration And Production ◽  
Oil And Gas Operations

Facts are stubborn things; and whatever may be our wishes, our inclinations, or the dictates of our passion, they cannot alter the state of facts and evidence (Adams 1770). Some people unfamiliar with upstream petroleum operations, some enterprises keen to sustain uncontested land use, and some people against the use of fossil fuels have and will voice opposition to land access for oil and gas exploration and production. Social and economic concerns have also arisen with Australian domestic gas prices tending towards parity with netbacks from liquefied natural gas (LNG) exports. No doubt, natural gas, LNG and crude-oil prices will vary with local-to-international supply-side and demand-side competition. Hence, well run Australian oil and gas producers deploy stress-tested exploration, delineation and development budgets. With these challenges in mind, successive governments in South Australia have implemented leading-practice legislation, regulation, policies and programs to simultaneously gain and sustain trust with the public and investors with regard to land access for trustworthy oil and gas operations. South Australia’s most recent initiatives to foster reserve growth through welcomed investment in responsible oil and gas operations include the following: a Roundtable for Oil and Gas; evergreen answers to frequently asked questions, grouped retention licences that accelerate investment in the best of play trends; the Plan for ACcelerating Exploration (PACE) Gas Program; and the Oil and Gas Royalty Return Program. Intended and actual outcomes from these initiatives are addressed in this extended abstract.

scholarly journals Internal face finishing for a cooling channel using a fluid containing free abrasive grains

2021 ◽  
Author(s):  
Mitsugu Yamaguchi ◽  
Tatsuaki Furumoto ◽  
Shuuji Inagaki ◽  
Masao Tsuji ◽  
Yoshiki Ochiai ◽  
...  
Keyword(s):  
High Speed ◽  
Flow Behavior ◽  
Flow Simulation ◽  
Cooling Channel ◽  
H13 Steel ◽  
Channel Diameter ◽  
Abrasive Grains ◽  
Low Viscosity ◽  
Short Period ◽  
Internal Pressures

AbstractIn die-casting and injection molding, a conformal cooling channel is applied inside the dies and molds to reduce the cycle time. When the internal face of the channel is rough, both cooling performance and tool life are negatively affected. Many methods for finishing the internal face of such channels have been proposed. However, the effects of the channel diameter on the flow of a low-viscosity finishing media and its finishing characteristics for H13 steel have not yet been reported in the literature. This study addresses these deficiencies through the following: the fluid flow in a channel was computationally simulated; the flow behavior of abrasive grains was observed using a high-speed camera; and the internal face of the channel was finished using the flow of a fluid containing abrasive grains. The flow velocity of the fluid with the abrasive grains increases as the channel diameter decreases, and the velocity gradient is low throughout the channel. This enables reduction in the surface roughness for a short period and ensures uniform finishing in the central region of the channel; however, over polishing occurs owing to the centrifugal force generated in the entrance region, which causes the form accuracy of the channel to partially deteriorate. The outcomes of this study demonstrate that the observational finding for the finishing process is consistent with the flow simulation results. The flow simulation can be instrumental in designing channel diameters and internal pressures to ensure efficient and uniform finishing for such channels.

Sign in / Sign up

Export Citation Format

Share Document