scholarly journals Applications of Biodiesel in Drilling Fluids

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Ashraf Ahmed ◽  
Salaheldin Elkatatny ◽  
Saad Al-Afnan
Keyword(s):  
Chemical Reactivity ◽  
Drilling Fluid ◽  
Chemical Properties ◽  
Temperature Stability ◽  
Lessons Learned ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Long Chain Fatty Acid ◽  
Drilling Muds ◽  
Physical And Chemical

Biodiesel, referred to as the monoalkyl ester of long-chain fatty acid ester that is synthesized by the complete transesterification of triglycerides, has captured the attention of drilling researchers attributing to its magnificent characteristics such as the high flash point, excellent lubricity, nontoxicity, high biodegradability, and abundant feedstock resources, which make it ecofriendly and technically and economically feasible for a sustainable drilling operation. There are several studies that reported and documented the usage of biodiesel in drilling fluids on laboratory and field scales. In this paper, the production and the key physical and chemical properties of biodiesel are thoroughly reviewed. Moreover, the applications of biodiesel in drilling muds either as base fluids or additives were comprehensively surveyed. The literature review revealed that the challenges of biodiesel applications in drilling mud systems are related to its chemical reactivity and adverse interactions with some additives, along with its performance deficiency at temperature above 120°C. Therefore, further investigation on temperature stability and additive compatibility is recommended. In addition, as a new approach, it is recommended to study the potentiality of using crude waste oils in drilling mud formulations. The lessons learned and recommendations stated in this paper will assist in enhancing the proved use of biodiesel and drilling fluid optimization.

Basic Performance Research of Polymer Intercalation Clay

2012 ◽  
Vol 578 ◽  
pp. 183-186
Author(s):  
Xiao Chun Cao ◽  
Yi Qin ◽  
Yan Na Zhao ◽  
Kun Ke
Keyword(s):  
Drilling Fluid ◽  
Chemical Properties ◽  
Drilling Fluids ◽  
Technical Problems ◽  
Clay Particles ◽  
Polymer Properties ◽  
Physical And Chemical ◽  
Performance Research ◽  
And Chemical Properties

Using the preliminary research of the polymer properties, the different between the physical and chemical properties of new polymer-clays nanometer composites and clay have been studied. Different polymers are used to evaluate experiment. Based on a large number of lab experiments, the changes of rheological property and API filtration property of polymer-clay drilling fluids nanometer composites are studied. The results show that clay particles could become smaller and the composites drilling fluid have the role of controlling loss and enhancing cake quality. The prepared composites could be used to solve the technical problems in drilling fluid.

scholarly journals Modification of DS-01 Drilling Fluid to Reduce Formation Damage

2020 ◽  
Vol 2 (3) ◽  
Author(s):  
Winarto S. ◽  
Sugiatmo Kasmungin
Keyword(s):  
Oil And Gas ◽  
Drilling Fluid ◽  
Laboratory Research ◽  
Formation Damage ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Initial Flow ◽  
Lost Circulation ◽  
Negative Impacts ◽  
Drilling Muds

<em>In the process of drilling for oil and gas wells the use of appropriate drilling mud can reduce the negative impacts during ongoing drilling and post-drilling operations (production). In general, one of the drilling muds that are often used is conventional mud type with weighting agent barite, but the use of this type of mud often results in skin that is difficult to clean. Therefore in this laboratory research an experiment was carried out using a CaCO3 weigting agent called Mud DS-01. CaCO3 is widely used as a material for Lost Circulation Material so that it is expected that using CaCO3 mud will have little effect on formation damage or at least easily cleaned by acidizing. The aim of this research is to obtain a formula of mud with CaCO3 which at least gives formation damage. Laboratory experiments on this drilling mud using several mud samples adjusted to the property specifications of the mud program. Mud sample consists of 4, namely using super fine, fine, medium, and conventional CaCO3. First measuring mud properties in each sample then testing the filter cake breaker, testing the initial flow rate using 200 ml of distilled water and a 20 micron filter disk inserted in a 500 ml HPHT cell then assembled in a PPA jacket and injecting a pressure of 100 psi. The acidification test was then performed using 15% HCL and then pressured 100 psi for 3 hours to let the acid work to remove the cake attached to the filter disk (acidizing). Laboratory studies are expected which of these samples will minimize the formation damage caused by drilling fluids.</em>

scholarly journals Investigation of Non-Linear Rheological Characteristics of Barite-Free Drilling Fluids

Fluids ◽  
2021 ◽  
Vol 6 (9) ◽  
pp. 327
Author(s):  
Ekaterina Leusheva ◽  
Nataliia Brovkina ◽  
Valentin Morenov
Keyword(s):  
Oil And Gas ◽  
Drilling Fluid ◽  
Rheological Parameters ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Gas Wells ◽  
Oil And Gas Wells ◽  
Fluid Properties ◽  
Hydrolyzed Polyacrylamide ◽  
Drilling Muds

Drilling fluids play an important role in the construction of oil and gas wells. Furthermore, drilling of oil and gas wells at offshore fields is an even more complex task that requires application of specialized drilling muds, which are non-Newtonian and complex fluids. With regard to fluid properties, it is necessary to manage the equivalent circulation density because its high values can lead to fracture in the formation, loss of circulation and wellbore instability. Thus, rheology of the used drilling mud has a significant impact on the equivalent circulation density. The aim of the present research is to develop compositions of drilling muds with a low solids load based on salts of formate acid and improve their rheological parameters for wells with a narrow drilling fluid density range. Partially hydrolyzed polyacrylamide of different molecular weights was proposed as a replacement for hydrolized polyacrylamide. The experiment was conducted on a Fann rotary viscometer. The article presents experimentally obtained data of indicators such as plastic viscosity, yield point, nonlinearity index and consistency coefficient. Experimental data were analyzed by the method of approximation. Analysis is performed in order to determine the most suitable rheological model, which describes the investigated fluids’ flow with the least error.

pH-Sensor Under Consideration for Multi-Sensor-Chip in Downhole Drilling Fluid Monitoring

2017 ◽  
Author(s):  
Jonathan Kühne ◽  
Frederic Güth ◽  
Heike Strauß ◽  
Yvonne Joseph ◽  
Pál Árki
Keyword(s):  
Optical Sensors ◽  
Drilling Fluid ◽  
Drill String ◽  
Glass Electrode ◽  
Drilling Fluids ◽  
Drilling Process ◽  
Ph Sensing ◽  
Drilling Mud ◽  
Ph Sensors ◽  
Drilling Muds

Modern drill strings for the exploration of oil and gas are equipped with a variety of sensor carrying devices such as Measurement While Drilling (MWD), Logging While Drilling (LWD), and Formation Testing While Drilling (FTWD). These devices generate a large amount of downhole data, such as the orientation of the well, drilling parameters e.g. weight on bit and torque, and formation properties. Appropriate telemetry systems are included in the drill string to transfer relevant downhole data in real time to the surface. Other data is stored in memories downhole for subsequent evaluation. However, drilling fluid properties are still monitored at the surface and their behavior under borehole conditions is predicted with hydraulic models. Commercial solutions for a direct downhole measurement of various drilling fluid parameters are rare, though they would increase drilling process safety and the knowledge about the behavior of drilling fluids under real bottomhole conditions. The pH has a significant influence on the properties of water-based muds and plays a role in the chemistry of oil-based muds as the water cut in the emulsion increases. Commercial pH-sensing devices, such as the glass electrode, and optical sensors are not appropriate for the pH measurement under bottomhole conditions. Fragility, the insufficient degree of miniaturization, the low temperature and pressure resistance due to the liquid reference electrolyte, and phenomena such as the alkaline error are certain drawbacks of glass electrodes. Often optical sensors often will not capture the whole pH scale and require the medium to be at least slightly transparent for light. The usage of pH-sensors based on EIS (electrolyte-isolator-semiconductor) structures is a possible application of chemical sensors for drilling fluid monitoring under in situ borehole conditions. This paper presents results from a study on the behavior of an EIS structure as a pH sensitive electrode measured vs. a commercial Ag/AgCl reference electrode in comparison with a commercial glass electrode. EIS structures are capacitive pH sensors where the sensing layer is generally a metal oxide on a semiconductor substrate. Measurements in basic drilling muds were conducted under constant temperature and atmospheric pressure while the drilling mud was steadily stirred. The mud was titrated from alkaline to acidic conditions with hydrochloric acid and the pH was measured after potential equilibration at the electrodes. The results show a general feasibility for the usage of the proposed sensor. There are still certain challenges to be overcome in the development of a robust and reliable pH-sensing device for complex fluids, such as drilling muds under high pressure/high temperature (HP/HT) conditions.

Investigation of Drilling Problems in Gas Hydrate Formations

2008 ◽  
Author(s):  
Catalin Teodoriu ◽  
Gioia Falcone ◽  
Amodu Afolabi
Keyword(s):  
Gas Hydrates ◽  
Gas Hydrate ◽  
Oil And Gas ◽  
Drilling Fluid ◽  
Hydrate Formation ◽  
Oil And Gas Industry ◽  
Lessons Learned ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Gas Hydrate Formation

Gas hydrates are ice-like crystalline systems made of water and methane that are stable under high pressure and low temperature conditions. Gas hydrates have been identified as strategic resources and may surpass all known oil and gas reserves combined. However, these resources will become reserves only if the gas contained therein can be produced economically. In the oil and gas industry, gas hydrates may be encountered while drilling sediments of the subsea continental slopes and in the subsurface of permafrost regions. They also represent a flow assurance issue, as they may form in the well and in the flowlines, causing blockages. Deepwater drilling programmes have experienced problems when encountering gas hydrate formations. A major issue is that of phase transition, where gas hydrate goes from a solid state to dissociated gas and water, as there are rapid changes in fluid volumes and pressure. This can cause drilling equipment failure, borehole instability and formation collapse. After dissociation of water and gas, hydrates may be prevented from forming in the well by using appropriate inhibitors in the drilling mud. There is a need to develop fluids specifically for drilling through gas hydrate formations, either to unlock the unconventional reserves trapped in the crystalline gas hydrate structures or to safely reach underlying conventional reserves. To drill wells in a gas hydrate formation, a conductor casing is needed to allow close loop circulation of the mud, if different from seawater. The search for the ideal mud for drilling through gas hydrate formations must start with a review of past experiences worldwide and of the lessons learned. This paper presents a review of the problems encountered while drilling through gas hydrate formations. It identifies the key requirements for drilling fluids, based on the interaction between the drill bit, the drilling fluid and the formation. An evaluation of the environmental risk associated with drilling through gas hydrate formations is also presented.

scholarly journals Dependence of the Equivalent Circulation Density of Formate Drilling Fluids on the Molecular Mass of the Polymer Reagent

Energies ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7639
Author(s):  
Ekaterina Leusheva ◽  
Valentin Morenov ◽  
Tianle Liu
Keyword(s):  
Molecular Weight ◽  
Formic Acid ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Technological Parameters ◽  
Gas Wells ◽  
Flow Rates ◽  
Hydrolyzed Polyacrylamide ◽  
Drilling Muds

Construction of offshore gas wells is characterized by increased requirements for both the technological process in general and the technological parameters of drilling fluids in particular. Parameters and properties of the used drilling muds must meet a large number of requirements. The main one is the preservation of the permeability of the reservoirs, in addition to the environmental and technological concerns. At the same time, pressures in the productive formation at offshore fields are often high; the anomaly coefficient is 1.2 and higher. The use of barite in such conditions can lead to contamination of the formation and a decrease in future well flow rates. In this regard, the development and study of the compositions for weighted drilling muds is necessary and relevant. The paper presents investigations on the development of such a composition based on salts of formic acid (formates) and evaluates the effect of the molecular weight of the polymer reagent (partially hydrolyzed polyacrylamide) on the equivalent circulation density of the drilling fluid. The result of the work is a formate-based high-density drilling mud with no barite added. Application of such a mud will preserve the permeability of the productive formation.

scholarly journals Topological invariants for the line graphs of some classes of graphs

2019 ◽  
Vol 17 (1) ◽  
pp. 1483-1490
Author(s):  
Xiaoqing Zhou ◽  
Mustafa Habib ◽  
Tariq Javeed Zia ◽  
Asim Naseem ◽  
Anila Hanif ◽  
...  
Keyword(s):  
Communication Theory ◽  
Chemical Reactivity ◽  
Line Graph ◽  
Chemical Properties ◽  
Topological Invariants ◽  
Line Graphs ◽  
Physical And Chemical Properties ◽  
Physical And Chemical ◽  
Ladder Graphs ◽  
And Chemical Properties

AbstractGraph theory plays important roles in the fields of electronic and electrical engineering. For example, it is critical in signal processing, networking, communication theory, and many other important topics. A topological index (TI) is a real number attached to graph networks and correlates the chemical networks with physical and chemical properties, as well as with chemical reactivity. In this paper, our aim is to compute degree-dependent TIs for the line graph of the Wheel and Ladder graphs. To perform these computations, we first computed M-polynomials and then from the M-polynomials we recovered nine degree-dependent TIs for the line graph of the Wheel and Ladder graphs.

scholarly journals Comparative Analysis of the Effect of Barite and Hematite on the Rheology of Water-Based Drilling Mud

2021 ◽  
Vol 1 (2) ◽  
Author(s):  
Osei H
Keyword(s):  
Rheological Properties ◽  
Drilling Fluid ◽  
Attrition Rate ◽  
Drilling Mud ◽  
Cleaning Efficiency ◽  
Drilling Operation ◽  
Water Based ◽  
Petroleum Resources ◽  
Drilling Muds ◽  
The Impact

High demand for oil and gas has led to exploration of more petroleum resources even at remote areas. The petroleum resources are found in deeper subsurface formations and drilling into such formations requires a well-designed drilling mud with suitable rheological properties in order to avoid or reduce associated drilling problems. This is because rheological properties of drilling muds have considerable effect on the drilling operation and cleaning of the wellbore. Mud engineers therefore use mud additives to influence the properties and functions of the drilling fluid to obtain the desired drilling mud properties especially rheological properties. This study investigated and compared the impact of barite and hematite as weighting agents for water-based drilling muds and their influence on the rheology. Water-based muds of different concentrations of weighting agents (5%, 10%, 15% and 20% of the total weight of the drilling mud) were prepared and their rheological properties determined at an ambient temperature of 24ᵒC to check their impact on drilling operation. The results found hematite to produce higher mud density, plastic viscosity, gel strength and yield point when compared to barite at the same weighting concentrations. The higher performance of the hematite-based muds might be attributed to it having higher specific gravity, better particle distribution and lower particle attrition rate and more importantly being free from contaminants. The water-based muds with hematite will therefore be more promising drilling muds with higher drilling and hole cleaning efficiency than those having barite.

scholarly journals Numerical Modeling of Foam Drilling Hydraulics

2007 ◽  
Vol 4 (1) ◽  
pp. 103 ◽  
Author(s):  
Ozcan Baris ◽  
Luis Ayala ◽  
W. Watson Robert
Keyword(s):  
Drilling Fluid ◽  
Operating Conditions ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Lost Circulation ◽  
Pressure Profiles ◽  
Drilling Operations ◽  
Parametric Studies ◽  
Bit Life ◽  
Foam Drilling

The use of foam as a drilling fluid was developed to meet a special set of conditions under which other common drilling fluids had failed. Foam drilling is defined as the process of making boreholes by utilizing foam as the circulating fluid. When compared with conventional drilling, underbalanced or foam drilling has several advantages. These advantages include: avoidance of lost circulation problems, minimizing damage to pay zones, higher penetration rates and bit life. Foams are usually characterized by the quality, the ratio of the volume of gas, and the total foam volume. Obtaining dependable pressure profiles for aerated (gasified) fluids and foam is more difficult than for single phase fluids, since in the former ones the drilling mud contains a gas phase that is entrained within the fluid system. The primary goal of this study is to expand the knowledge-base of the hydrodynamic phenomena that occur in a foam drilling operation. In order to gain a better understanding of foam drilling operations, a hydrodynamic model is developed and run at different operating conditions. For this purpose, the flow of foam through the drilling system is modeled by invoking the basic principles of continuum mechanics and thermodynamics. The model was designed to allow gas and liquid flow at desired volumetric flow rates through the drillstring and annulus. Parametric studies are conducted in order to identify the most influential variables in the hydrodynamic modeling of foam flow. 

Case Study of Identifying and Minimizing Formation Damage in Tight Reservoirs Caused by Drilling Fluids in Abu Dhabi Onshore Operation Using Compatibility Coreflood Studies

2021 ◽  
Author(s):  
Raymond Saragi ◽  
Mohammad Husien ◽  
Dalia Salim Abdullah ◽  
Ryan McLaughlin ◽  
Ian Patey ◽  
...  
Keyword(s):  
Positive Impact ◽  
Abu Dhabi ◽  
Formation Damage ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Hydrocarbon Recovery ◽  
Tight Reservoirs ◽  
Filtrate Loss ◽  
Drilling Muds ◽  
Loss Control

Abstract A study was carried out to examine formation damage mechanisms caused by drilling fluids in tight reservoirs in several onshore oil fields in Abu Dhabi. Three phases of compatibility corefloods were carried out to identify potential to improve hydrocarbon recovery and examine reformulated/alternate drilling muds and treatment fluids. Interpretation was aided by novel Nano-CT quantifications and visualisations. The first phase examined the current drilling muds and showed inconsistent filtrate loss control alongside high levels of permeability alteration. These alterations were caused by retention of drilling mud constituents in the near-wellbore and incomplete clean-up of drilling mud-cakes. Based upon these results, reformulated and alternate drilling muds were examined in Phase 2, and there was a positive impact upon both filtrate loss and permeability, although the Nano-CT quantifications and visualisations showed that drilling mud constituents were still having an impact upon permeability. Candidate treatment fluids were examined in Phase 3, with all having a positive impact and the best performance coming from 15% HCl and an enzyme-based treatment. The interpretative tools showed that these treatments had removed drilling mud-cakes, created wormholes, and bypassed the areas where constituents were retained. The compatibility corefloods on tight reservoir core, alongside high-resolution quantifications and visualisations, therefore identified damaging mechanisms, helped identify potential to improve hydrocarbon recovery, and identify treatment fluid options which could be used in the fields.

Sign in / Sign up

Export Citation Format

Share Document