scholarly journals Activated Carbon from the Peelings of Cassava Tubers (Manihot esculenta) for the Removal of Nickel(II) Ions from Aqueous Solution

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Brice Armel Ajouafeu Alongamo ◽  
Lydie Dodo Ajifack ◽  
Julius Numbonui Ghogomu ◽  
Ndi Julius Nsami ◽  
Joseph Mbadcam Ketcha
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Manihot Esculenta ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Activation ◽  
Zero Point ◽  
Batch Adsorption ◽  
Homogeneous Surface

Activated carbons were obtained from the peelings of cassava tubers (Manihot esculenta) by chemical activation using potassium hydroxide and phosphoric acid at impregnation ratios of 2 : 1 and 1 : 1, respectively, at 400°C for batch adsorption of nickel(II) ions from aqueous solution. Characterization of activated carbon samples was achieved via proximate analysis, Fourier-transform infrared spectroscopy, pH of zero-point charge, Boehm method, elemental analysis, scanning electron microscopy, and iodine number determination for each adsorbent. The effects of pH, contact time, initial adsorbate concentration, and adsorbent dose were studied at 27°C in order to optimize the conditions for maximum adsorption. Equilibrium was attained after 40 minutes of contact of both materials with activating solutions. Maximum adsorption capacities of 41.15 mg/g for ACPH, 47.39 mg/g for ACPA, 35.34 mg/g for NIC, and 34.48 mg/g for RM, respectively, were obtained at pH = 4. Equilibrium data showed that the Langmuir model best described the adsorption process with R2 closed to unity, indicative of monolayer adsorption on a homogeneous surface. Kinetic studies showed that the adsorption process is controlled by the pseudo-second-order model. These results show that activated carbon prepared from cassava peelings constitutes an effective low-cost material for the treatment of wastewater containing nickel(II) ions.

scholarly journals Removal of Ni (II) from Aqueous Solution by Adsorption onto Activated Carbon Prepared from Lapsi (Choerospondias axillaris) Seed Stone

2014 ◽  
Vol 9 (1) ◽  
pp. 166-174 ◽  
Author(s):  
Rajeshwar M. Shrestha ◽  
Margit Varga ◽  
Imre Varga ◽  
Amar P. Yadav ◽  
Bhadra P. Pokharel ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Characterization ◽  
Maximum Adsorption Capacity ◽  
Adsorption Data ◽  
Optimum Ph ◽  
Nickel Adsorption

Activated carbons were prepared from Lapsi seed stone by the treatment with H2SO4 and HNO3 for the removal of Ni (II) ions from aqueous solution. Two activated carbon have been prepared from Lapsi seed stones by treating with conc.H2SO4 and a mixture of H2SO4 and HNO3 in the ratio of 1:1 by weight for removal of Ni(II) ions. Chemical characterization of the resultant activated carbons was studied by Fourier Transform Infrared Spectroscopy and Boehm titration which revealed the presence of oxygen containing surface functional groups like carboxyl, lactones and phenols in the carbons. The optimum pH for nickel adsorption is found to be 5. The adsorption data were better fitted with the Langmuir equations than Freundlich adsorption equation to describe the equilibrium isotherms. The maximum adsorption capacity of Ni (II) on the resultant activated carbons was 28.25.8 mg g-1 with H2SO4 and 69.49 mg g-1 with a mixture of H2SO4 and HNO3. The waste material used in the preparation of the activated carbons is inexpensive and readily available. Hence the carbons prepared from Lapsi seed stones can act as potential low cost adsorbents for the removal of Ni (II) from water. DOI: http://dx.doi.org/10.3126/jie.v9i1.10680Journal of the Institute of Engineering, Vol. 9, No. 1, pp. 166–174

Adsorptive Removal of Pb(II) Ion from Aqueous Solution Using Rice Husk-Based Activated Carbon

2014 ◽  
Vol 875-877 ◽  
pp. 196-201 ◽  
Author(s):  
Mohd Faisal Taha ◽  
Ahmad S. Rosman ◽  
Maizatul S. Shaharun
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Rice Husk ◽  
Low Cost ◽  
Chemical Activation ◽  
Textural Properties ◽  
Activation Process ◽  
Adsorption Studies ◽  
Three Samples ◽  
Equilibrium Data

The potential of rice husk-based activated carbon as an alternative low-cost adsorbent for the removal of Pb (II) ion from aqueous solution was investigated. Rice husk-based activated carbon was preparedviachemical activation process using NaOH followed by the carbonization process at 500°C. Morphological analysis was conducted using field-emission scanning electron microscope /energy dispersive X-ray (FESEM/EDX) on three samples, i.e. raw rice husk, rice husk treated with NaOH and rice husk-based activated carbon. These three samples were also analyzed for their C, H, N, O and Si contents using CHN elemental analyzer and FESEM/EDX. The textural properties of rice husk-based activated carbon, i.e. surface area (253 m2/g) and pore volume (0.17 cm2/g), were determined by N2adsorption. The adsorption studies using rice husk-based activated carbon as an adsorbent to remove Pb (II) ion from aqueous solution were carried out at a fixed initial concentration of Pb (II) ion (150 ppm) with varying adsorbent dose as a function of contact time at room temperature. The concentration of Pb (II) ion was determined by atomic absorption spectrophotometer (AAS). The removal of Pb (II) ion from aqueous solution increased from 35 % to 82 % when the amount of rice husk-based activated carbon was increased from 0.05 g to 0.30 g. The equilibrium data obtained from adsorption studies was found to fit both Langmuir and Freundlich adsorption isotherms.

scholarly journals Performance of Sweet Potato’s Leaf-Derived Activated Carbon for Hydrogen Sulphide Removal from Biogas

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Geni Juma ◽  
Revocatus Machunda ◽  
Tatiana Pogrebnaya
Keyword(s):  
Activated Carbon ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Carbonization Temperature ◽  
Optimal Test ◽  
Potato Leaf ◽  
Bet Analysis ◽  
S 100 ◽  
Activation Ratio

In this study, sweet potato leaf activated carbon (SpLAC) was prepared by the chemical activation method using KOH and applied as an adsorbent for H2S removal from biogas. The study focused on the understanding of the effect of carbonization temperature (Tc), varying KOH : C activation ratio, flow rate (FR) of biogas, and mass of SpLAC on sample adsorption capacity. The BET analysis was performed for both fresh and spent activated carbons as well as for carbonized samples, which were not activated; also, the activated carbon was characterized by XRF and CHNS techniques. The results showed that removal efficiency (RE) of the SpLAC increased with increase carbonization temperature from 600 to 800°C and the mass of sorbent from 0.4 g to 1.0 g. The optimal test conditions were determined: 1.0 g of sorbent with a KOH : C ratio of 1 : 1, Tc=800°C, and FR=0.02 m3/h which resulted in a sorption capacity of about 3.7 g S/100 g of the SpLAC. Our findings corroborated that H2S removal was contributed not only by the adsorption process with the pore available but also by the presence of iron in the sample that reacted with H2S. Therefore, upon successful H2S sorption, SpLAC is suggested as a viable adsorbent for H2S removal from biogas.

Removal of Methylene Blue by Adsorption Process - A Comparative Study

2011 ◽  
Vol 699 ◽  
pp. 245-264 ◽  
Author(s):  
A. Xavier ◽  
J. Gandhi Rajan ◽  
D. Usha ◽  
R Sathya
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Low Cost ◽  
Kinetic Equations ◽  
Dye Adsorption ◽  
Industrial Wastes ◽  
Blue Dye ◽  
Molecular Formula

Methylene blue is a heterocyclic aromatic chemical compound with the molecular formula C16H18N3SCl. It has used in the biology and chemistry field. At room temperature, it appears as a solid, odourless dark green powder that yields blue solution when dissolved in water. As a part of removal of methylene blue dye from textile and leather industrial wastes, using activated carbon as adsorbents namely, commercial activated carbon (CAC), rose apple carbon (RAC), coconut shell carbon (CSC) and saw dust carbon (SDC). The percentage of Methylene blue adsorbed increases with decrease in initial concentration and particle size of adsorbent and increased with increase in contact time, temperature and dose of adsorbents. The pH is highly sensitive for dye adsorption process. The adsorption process followed first order kinetics and the adsorption data the modeled with Freundlich and Langmuir isotherms. The first kinetic equations like Natarajan Khalaf, Lagergren, Bhattacharya and Venkobhachar and intra particle diffusion were found to be applicable. A comparative account of the adsorption capacity of various carbons has been made. These activated carbons are alternative to commercial AC for the removal dyes in General and MB is particular. These results are reported highly efficient and effective and low cost adsorbent for the MB. The thermodynamics parameters are also studied and it obeys spontaneous process. The results are confirmed by before and after adsorption process with the help of the following instrumental techniques viz., FT-IR, UV-Visible Spectrophotometer and SEM photos.

scholarly journals Comparison of Surface and Structural Properties of Carbonaceous Materials Prepared by Chemical Activation of Tomato Paste Waste: The Effects of Activator Type and Impregnation Ratio

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Nurgul Ozbay ◽  
Adife Seyda Yargic
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Activation ◽  
Nitrogen Adsorption ◽  
Xrd Analysis ◽  
Point Of Zero Charge ◽  
Activation Process ◽  
X Ray ◽  
Tomato Paste

Activated carbons were prepared by carbonization of tomato paste processing industry waste at 500°C followed by chemical activation with KOH, K2CO3, and HCl in N2 atmosphere at low temperature (500°C). The effects of different activating agents and impregnation ratios (25, 50, and 100 wt.%) on the materials’ characteristics were examined. Precursor, carbonized tomato waste (CTW), and activated carbons were characterized by using ultimate and proximate analysis, thermogravimetric analysis (TG/DTG), Fourier transform-infrared (FT-IR) spectroscopy, X-ray fluorescence (XRF) spectroscopy, point of zero charge measurements (pHPZC), particle size analyzer, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) spectroscopy, nitrogen adsorption/desorption isotherms, and X-ray diffraction (XRD) analysis. Activation process improved pore formation and changed activated carbons’ surface characteristics. Activated carbon with the highest surface area (283 m3/g) was prepared by using 50 wt.% KOH as an activator. According to the experimental results, tomato paste waste could be used as an alternative precursor to produce low-cost activated carbon.

scholarly journals Batch adsorption studies for ketoprofen removal via Dillenia Indica peel activated carbon

2021 ◽  
Vol 920 (1) ◽  
pp. 012010
Author(s):  
F Fadzail ◽  
M Hasan ◽  
Z Mokhtar ◽  
N Ibrahim ◽  
O S An ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Process ◽  
Chemical Activation ◽  
Batch Adsorption ◽  
Order Model ◽  
Batch Mode ◽  
Adsorbent Dosage ◽  
Pseudo Second Order ◽  
Dillenia Indica ◽  
Experimental Findings

Abstract Removal of ketoprofen using Dillenia Indica peel activated carbon was investigated using batch adsorption at a laboratory scale. Chemical activation method with the aid of phosphoric acid was utilised in preparing the activated carbon. The adsorption experiments were evaluated using various factors which, are initial concentration, adsorbent dosage, and pH of ketoprofen. The optimum condition was determined to be at pH 6 and adsorbent dosage of 0.4 g with a most KTP uptake of 8.354 mg/g. The experimental findings showed that adsorption is favorable at lower pH. Isotherm studies were conducted and the data indicated that Langmuir isotherm was well fitted to the adsorption process and the pseudo-second-order model was more preferable in simulating the kinetic process. In essence, Dillenia Indica peel activated carbon was proven as being a favourable adsorbent for the uptake of ketoprofen in batch mode.

scholarly journals Optimization of Zinc(II) Adsorption Using Agricultural Waste

2018 ◽  
Vol 7 (3.34) ◽  
pp. 300
Author(s):  
Gobinath Ravindran ◽  
M Radha Madhavi ◽  
Bashir Suleman Abusahmin
Keyword(s):  
Waste Water ◽  
Activated Carbon ◽  
Adsorption Process ◽  
Low Cost ◽  
Agricultural Waste ◽  
Solution Concentration ◽  
Batch Adsorption ◽  
Industrial Growth ◽  
Palm Shell ◽  
Independent Process

With industrial growth, presence of pollutants is growing enormously. Removal of pollutant from waste water and effluents can be accomplished by various techniques, out of which adsorption was found to be an efficient method. Applications of adsorption limits itself due to high cost of adsorbent. In this regard, a low cost adsorbent produced from palm oil shell based agricultural waste is examined for its efficiency to remove Zn (II) from waste water and aqueous solution. The influence of independent process variables like pH, residence time, initial solution concentration, activated carbon dosage and process temperature on the removal of Zn(II) by palm shell based activated carbon from batch adsorption process are studied systematically. The results reveal that palm shell based activated carbon can be an effective adsorbent for removal of Zinc (II) and is efficient compared to other types of adsorbent produced from agricultural waste.  

scholarly journals Removal of Cd (II) ions from Aqueous Solution by Adsorption on Activated Carbon Prepared from Lapsi (Choerospondias axillaris) Seed Stone

2016 ◽  
Vol 11 (1) ◽  
pp. 140-150 ◽  
Author(s):  
Rajeshwar Man Shrestha
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Metal Ion ◽  
Activated Carbons ◽  
Freundlich Isotherm ◽  
Batch Adsorption ◽  
Metal Ion Removal ◽  
Ion Removal ◽  
Equilibrium Data ◽  
Methylene Blue Number

Batch adsorption experiments were conducted for the adsorption of Cd (II) ions from aqueous solution by activated carbon prepared from Lapsi seed stone. The activated carbon was characterized by Iodine number, Methylene blue number, SEM and FTIR. Adsorption experiments were carried out to describe the effect of pH ,contact time and  adsorbent dose on the metal ion removal process .The results showed that the adsorption of Cd (II) ions was very fast initially and the equilibrium time was 3 hrs.The pH of 6.0 was an optimal pH for adsorption  of Cd(II) ions. Langmuir and Freundlich adsorption isotherms were used to explain the equilibrium data. Langmuir model best described the data with higher value of coeffcient of determination as −1 compared to that of Freundlich isotherm showing a maximum uptake of 37.0 mgg . This study demonstrated that the activated carbons prepared from Lapsi seed stone could be used for the removal of Cd (II) ions in water treatment. Journal of the Institute of Engineering, 2015, 11(1): 140-150

Removal of 4-nitrophenol from aqueous solution by adsorption onto activated carbon prepared from Acacia glauca sawdust

2015 ◽  
Vol 73 (4) ◽  
pp. 955-966 ◽  
Author(s):  
Prashant T. Dhorabe ◽  
Dilip H. Lataye ◽  
Ramakant S. Ingole
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Adsorption Process ◽  
Enthalpy Change ◽  
Optimum Dose ◽  
Batch Adsorption ◽  
Gibbs Free Energy Change ◽  
Pseudo Second Order ◽  
Percentage Removal ◽  
Maximum Removal

The present paper deals with a complete batch adsorption study of 4-nitrophenol (4NP) from aqueous solution onto activated carbon prepared from Acacia glauca sawdust (AGAC). The surface area of the adsorbent determined by methylene blue method is found to be 311.20 m2/g. The optimum dose of adsorbent was found to be 2 g/l with 4NP uptake of 25.93 mg/g. The equilibrium time was found to be 30 minutes with the percentage removal of 96.40 at the initial concentration of 50 ppm. The maximum removal of 98.94% was found to be at pH of 6. The equilibrium and kinetic study revealed that the Radke–Prausnitz isotherm and pseudo second order kinetics model fitted the respective data well. In the thermodynamic study, the negative value of Gibbs free energy change (−26.38 kJ/mol at 30°C) and enthalpy change (−6.12 kJ/mol) showed the spontaneous and exothermic nature of the adsorption process.

Sign in / Sign up

Export Citation Format

Share Document