scholarly journals Experimental Investigation on Multiscale Fracturing in Thermally Treated Sandstone under SHPB Impact Loading

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Shang Yang ◽  
Jun Wang ◽  
Zhi Zhang ◽  
Jianguo Ning ◽  
Guoqing Sun
Keyword(s):  
Split Hopkinson Pressure Bar ◽  
Class Ii ◽  
Temperature Treatment ◽  
Class I ◽  
Effect Of Temperature ◽  
Hopkinson Pressure Bar ◽  
Fracture Characteristics ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Thermally Treated

To study the effect of temperature on the dynamic mechanical behaviors and fracture characteristics of thermally treated sandstone, compressive dynamic loading experiments were performed on a series of samples using a split Hopkinson pressure bar (SHPB). In the tests, the dynamic uniaxial compressive strength of the thermally treated sandstone was inversely proportional to the temperature treatment in the range of 200°C–1000°C, while the dynamic elastic modulus first increased and then gradually decreased after different temperature treatments. The results show that two classical mechanical types (i.e., Class I and Class II) are observed from the dynamic stress-strain responses of SHPB tests for thermally treated sandstone. By means of scanning electron microscopy (SEM), the microdifference of postloading microfracture characteristics in Class I and Class II behavior was identified. In Class I behavior, intercrystalline cracks (IE) are the chief form of cracks on the fracture surface of a specimen fractured by SHPB loading even though there some intracrystalline cracks may also be present. In contrast, Class II behavior results from the chief cracking type being intracrystalline cracks.

scholarly journals Dynamic Mechanical Properties and Constitutive Relation of an Aluminized Polymer Bonded Explosive at Low Temperatures

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Yuliang Lin ◽  
Binbin Xu ◽  
Rong Chen ◽  
Jingui Qin ◽  
Fangyun Lu
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Extreme Environments ◽  
Dynamic Mechanical Properties ◽  
Experimental Results ◽  
Effect Of Temperature ◽  
Hopkinson Pressure Bar ◽  
Polymer Bonded Explosives ◽  
Split Hopkinson ◽  
Pressure Bar

Polymer bonded explosives (PBXs) are widely used as energetic fillings in various warheads, which maybe are utilized under extreme environments, such as low or high temperatures. In this paper, the dynamic response of an aluminized polymer bonded explosive was tested at a range of temperatures from −55°C to −2°C and a fixed loading strain rate (~700 s−1) with the split Hopkinson pressure bar (SHPB). The PBX tested is aluminized, which contains 76 wt% RDX, 20 wt% aluminum powder, and 4 wt% polymer binder, respectively. The results show that the effect of temperature on the strength of the PBX is obvious at the tested strain rates. Based on the experimental results and prophase studies, a constitutive model was obtained, in which the effect of temperature and strain rate were considered. The modeling curves fit well with the experimental results, not only at low temperature under 0°C, but also at room temperature (20°C). The model may be used to predict the dynamic performances of the PBXs in various environments.

Analysis of the Impact of the Frequency Range of the Tensometer Bridge and Projectile Geometry on the Results of Measurements by the Split Hopkinson Pressure Bar Method

2013 ◽  
Vol 20 (4) ◽  
pp. 555-564 ◽  
Author(s):  
Wojciech Moćko
Keyword(s):  
Test Bench ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Deformation ◽  
Spectral Width ◽  
Hopkinson Pressure Bar ◽  
Computing Environment ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
The Impact ◽  
Bench Model

Abstract The paper presents the results of the analysis of the striker shape impact on the shape of the mechanical elastic wave generated in the Hopkinson bar. The influence of the tensometer amplifier bandwidth on the stress-strain characteristics obtained in this method was analyzed too. For the purposes of analyzing under the computing environment ABAQUS / Explicit the test bench model was created, and then the analysis of the process of dynamic deformation of the specimen with specific mechanical parameters was carried out. Based on those tests, it was found that the geometry of the end of the striker has an effect on the form of the loading wave and the spectral width of the signal of that wave. Reduction of the striker end diameter reduces unwanted oscillations, however, adversely affects the time of strain rate stabilization. It was determined for the assumed test bench configuration that a tensometric measurement system with a bandwidth equal to 50 kHz is sufficient

Dynamic Behaviors of near β-Type Ti-5Al-5Mo-5V-3Cr Titanium Alloys under High Strain Rate

2015 ◽  
Vol 816 ◽  
pp. 795-803
Author(s):  
Yan Ling Wang ◽  
Song Xiao Hui ◽  
Wen Jun Ye ◽  
Rui Liu
Keyword(s):  
Strain Rate ◽  
Titanium Alloys ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Failure Behavior ◽  
Hopkinson Pressure Bar ◽  
Fracture Failure ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Dynamic Loading Conditions

The mechanical properties and fracture failure behavior of the near β-type Ti-5Al-5Mo-5V-3Cr-X (X = 1Fe or 1Zr) titanium alloys were studied by Split Hopkinson Pressure Bar (SHPB) experiment under the dynamic loading conditions at a strain rate of 1.5 × 103 s-1–5.0 × 103 s-1. Results showed that the SHPB specimen fractured in the direction of maximum shearing stress at an angle of 45° with the compression axis. The fracture surface revealed the shear and tension zones with cleavage steps and parabolic dimples. Severe early unloading was observed on the Ti-5553 alloy under a strain rate of 4,900 s-1 loading condition, and the dynamic property of the Ti-55531Zr alloy was proved to be the optimal.

Sign in / Sign up

Export Citation Format

Share Document