scholarly journals Dynamic Mechanical Properties and Constitutive Relation of an Aluminized Polymer Bonded Explosive at Low Temperatures

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Yuliang Lin ◽  
Binbin Xu ◽  
Rong Chen ◽  
Jingui Qin ◽  
Fangyun Lu
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Extreme Environments ◽  
Dynamic Mechanical Properties ◽  
Experimental Results ◽  
Effect Of Temperature ◽  
Hopkinson Pressure Bar ◽  
Polymer Bonded Explosives ◽  
Split Hopkinson ◽  
Pressure Bar

Polymer bonded explosives (PBXs) are widely used as energetic fillings in various warheads, which maybe are utilized under extreme environments, such as low or high temperatures. In this paper, the dynamic response of an aluminized polymer bonded explosive was tested at a range of temperatures from −55°C to −2°C and a fixed loading strain rate (~700 s−1) with the split Hopkinson pressure bar (SHPB). The PBX tested is aluminized, which contains 76 wt% RDX, 20 wt% aluminum powder, and 4 wt% polymer binder, respectively. The results show that the effect of temperature on the strength of the PBX is obvious at the tested strain rates. Based on the experimental results and prophase studies, a constitutive model was obtained, in which the effect of temperature and strain rate were considered. The modeling curves fit well with the experimental results, not only at low temperature under 0°C, but also at room temperature (20°C). The model may be used to predict the dynamic performances of the PBXs in various environments.

Experimental Research on Dynamic Mechanical Properties of 5083 Aluminum Alloy

2013 ◽  
Vol 535-536 ◽  
pp. 497-500 ◽  
Author(s):  
Zhi Wu Zhu ◽  
Guo Zheng Kang ◽  
Dong Ruan ◽  
Yue Ma ◽  
Guo Xing Lu
Keyword(s):  
Aluminum Alloy ◽  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Dynamic Mechanical Properties ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
5083 Aluminum Alloy

5083 aluminum alloy was investigated with respect to its uniaxial dynamic compressive properties over a range of strain rates using the split Hopkinson pressure bar (SHPB). The dynamic stress-strain curves of this alloy were obtained for strain rates from 1000 s-1 to 6000 s-1. Effects of strain rate, the samples size and anti-impact capability were analyzed. The experimental results show that under impaction loading, 5083 aluminum alloy has a remarkable strengthening response to strain rate and size; in particular, the responded stress increases with increasing strain rate, which implies that this alloy has high strength and high anti-impact capability.

scholarly journals Size Effect in the Split Hopkinson Pressure Bar Experiment

2022 ◽  
Vol 2160 (1) ◽  
pp. 012065
Author(s):  
Hailiang Nie ◽  
Weifeng Ma ◽  
Junjie Ren ◽  
Ke Wang ◽  
Jun Cao ◽  
...  
Keyword(s):  
Split Hopkinson Pressure Bar ◽  
Dynamic Testing ◽  
Impact Resistance ◽  
Dynamic Mechanical Properties ◽  
Experimental Results ◽  
Hopkinson Pressure Bar ◽  
Practical Engineering ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
The Impact

Abstract For many structures, their service environment is very strict, and the requirements for the impact resistance of materials are very high. Therefore, the dynamic testing method has important scientific significance and application value for practical engineering. Split Hopkinson pressure bar (SHPB) is one of the most common experimental methods for obtaining dynamic mechanical properties of materials. However, there is no uniform standard for the size of the bars and specimens used in the test. Theoretically, the size has little influence on the experimental results, but it has not been proved by experiments. This paper mainly studies the influence of device/specimen sizes of split Hopkinson pressure bar through experiments, it is demonstrated that the sizes of bars and specimen have little effect on experimental results.

Dynamic Behaviors of near β-Type Ti-5Al-5Mo-5V-3Cr Titanium Alloys under High Strain Rate

2015 ◽  
Vol 816 ◽  
pp. 795-803
Author(s):  
Yan Ling Wang ◽  
Song Xiao Hui ◽  
Wen Jun Ye ◽  
Rui Liu
Keyword(s):  
Strain Rate ◽  
Titanium Alloys ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Failure Behavior ◽  
Hopkinson Pressure Bar ◽  
Fracture Failure ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Dynamic Loading Conditions

The mechanical properties and fracture failure behavior of the near β-type Ti-5Al-5Mo-5V-3Cr-X (X = 1Fe or 1Zr) titanium alloys were studied by Split Hopkinson Pressure Bar (SHPB) experiment under the dynamic loading conditions at a strain rate of 1.5 × 103 s-1–5.0 × 103 s-1. Results showed that the SHPB specimen fractured in the direction of maximum shearing stress at an angle of 45° with the compression axis. The fracture surface revealed the shear and tension zones with cleavage steps and parabolic dimples. Severe early unloading was observed on the Ti-5553 alloy under a strain rate of 4,900 s-1 loading condition, and the dynamic property of the Ti-55531Zr alloy was proved to be the optimal.

Dynamic Hardness of MCrAlY Abradable Seal Coating

2021 ◽  
Vol 1035 ◽  
pp. 591-595
Author(s):  
Dan Guo ◽  
Jian Ming Liu ◽  
De Ming Zhang ◽  
Xin Zhang ◽  
Tong Liu
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Hopkinson Pressure Bar ◽  
Dynamic Hardness ◽  
Mcraly Coating ◽  
Static Hardness ◽  
Split Hopkinson ◽  
The Difference ◽  
Pressure Bar ◽  
Abradable Coatings

The purpose of this investigation is to study the dynamic hardness of MCrAlY abradable coatings under different strain rates. A dynamic indentation device based on the split Hopkinson pressure bar system (SHPB) was used. The results show that the hardness of MCrAlY coating increased with the increase of the strain rate, which has a positive strain rate effect. In addition, the difference of the static hardness of MCrAlY coating prepared by HVOF and LPPS was only 4%, while the difference in dynamic hardness was 16%.

scholarly journals Study on the dynamic properties of AM-SLM AlSi10Mg alloy using the Split Hopkinson Pressure Bar (SHPB) technique

2018 ◽  
Vol 183 ◽  
pp. 04005 ◽  
Author(s):  
Bar Nurel ◽  
Moshe Nahmany ◽  
Adin Stern ◽  
Nahum Frage ◽  
Oren Sadot
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Rate Sensitivity ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Static Mechanical ◽  
Split Hopkinson ◽  
Pressure Bar

Additive manufacturing by Selective Laser Melting of metals is attracting substantial attention, due to its advantages, such as short-time production of customized structures. This technique is useful for building complex components using a metallic pre-alloyed powder. One of the most used materials in AMSLM is AlSi10Mg powder. Additively manufactured AlSi10Mg may be used as a structural material and it static mechanical properties were widely investigated. Properties in the strain rates of 5×102–1.6×103 s-1 and at higher strain rates of 5×103 –105 s-1 have been also reported. The aim of this study is investigation of dynamic properties in the 7×102–8×103 s-1 strain rate range, using the split Hopkinson pressure bar technique. It was found that the dynamic properties at strain-rates of 1×103–3×103 s-1 depend on a build direction and affected by heat treatment. At higher and lower strain-rates the effect of build direction is limited. The anisotropic nature of the material was determined by the ellipticity of samples after the SHPB test. No strain rate sensitivity was observed.

scholarly journals Development of a True-Biaxial Split Hopkinson Pressure Bar Device and Its Application

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7298
Author(s):  
Shumeng Pang ◽  
Weijun Tao ◽  
Yingjing Liang ◽  
Shi Huan ◽  
Yijie Liu ◽  
...  
Keyword(s):  
Stress Wave ◽  
Impact Loading ◽  
Split Hopkinson Pressure Bar ◽  
Axial Stress ◽  
Dynamic Mechanical Properties ◽  
Stress Waves ◽  
Hopkinson Pressure Bar ◽  
Dynamic Mechanical ◽  
Split Hopkinson ◽  
Pressure Bar

Although highly desirable, the experimental technology of the dynamic mechanical properties of materials under multiaxial impact loading is rarely explored. In this study, a true-biaxial split Hopkinson pressure bar device is developed to achieve the biaxial synchronous impact loading of a specimen. A symmetrical wedge-shaped, dual-wave bar is designed to decompose a single stress wave into two independent and symmetric stress waves that eventually form an orthogonal system and load the specimen synchronously. Furthermore, a combination of ground gaskets and lubricant is employed to eliminate the shear stress wave and separate the coupling of the shear and axial stress waves propagating in bars. Some confirmatory and applied tests are carried out, and the results show not only the feasibility of this modified device but also the dynamic mechanical characteristics of specimens under biaxial impact loading. This novel technique is readily implementable and also has good application potential in material mechanics testing.

Sign in / Sign up

Export Citation Format

Share Document