scholarly journals Study on Variation of Surface Runoff and Soil Moisture Content in the Subgrade of Permeable Pavement Structure

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Lijun Hou ◽  
Yuan Wang ◽  
Fengchun Shen ◽  
Ming Lei ◽  
Xiang Wang ◽  
...  
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Soil Water ◽  
Surface Runoff ◽  
Rainfall Intensity ◽  
Soil Moisture Content ◽  
Asphalt Pavement ◽  
Infiltration Rate ◽  
Runoff Coefficient ◽  
Flood Peak

The self-designed indoor simulated rainfall device was used to rain on five types of pavement structures with 4 types of rainfall intensity (2.5 mm/min, 3.4 mm/min, 4.6 mm/min, and 5.5 mm/min). The effect of rainfall intensity on the surface runoff, the relation between the subgrade soil moisture content changes, and the influence of initial soil water content on rain infiltration rate are studied. The test results show that the surface runoff coefficient of densely asphalted pavement is greater than 90% in drainage pavements and it has little influence on the reducing and hysteresis of the flood peak. The surface runoff coefficient of large-void asphalt pavement (permeable) is less than 40%. Although the large-void asphalt pavement (permeable) can reduce a small amount of surface runoff, it has no obvious effect on the reduction and hysteresis of the flood peak. In semipermeable pavement, with the increasing of the thickness of base (graded gravel), the surface runoff coefficient decreases at different rainfall intensities, parts of the surface runoff are reduced, and the arrival of flood peaks is delayed. In permeable roads, almost no surface runoff occurred. As time continued, the soil moisture content quickly reached a saturated state and presented a stable infiltration situation under the action of gravity and the gradient of soil water suction. As the initial moisture content increases, the initial infiltration rate decreases and the time to reach a stable infiltration rate becomes shorter. The drier the soil, the greater the initial infiltration rate and the higher the soil moisture content after infiltration stabilization. Permeable roads can greatly alleviate the pressure of urban drainage and reduce the risk of storms and floods.

scholarly journals Identifying erosive periods by using RUSLE factors in mountain fields of the Central Spanish Pyrenees

2008 ◽  
Vol 12 (2) ◽  
pp. 523-535 ◽  
Author(s):  
M. López-Vicente ◽  
A. Navas ◽  
J. Machín
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Soil Loss ◽  
Rainfall Intensity ◽  
Soil Moisture Content ◽  
Rainfall Erosivity ◽  
Soil Erodibility ◽  
Maximum Rainfall ◽  
Freeze Thaw ◽  
Soil Losses

Abstract. The Mediterranean environment is characterized by strong temporal variations in rainfall volume and intensity, soil moisture and vegetation cover along the year. These factors play a key role on soil erosion. The aim of this work is to identify different erosive periods in function of the temporal changes in rainfall and runoff characteristics (erosivity, maximum intensity and number of erosive events), soil properties (soil erodibility in relation to freeze-thaw processes and soil moisture content) and current tillage practices in a set of agricultural fields in a mountainous area of the Central Pyrenees in NE Spain. To this purpose the rainfall and runoff erosivity (R), the soil erodibility (K) and the cover-management (C) factors of the empirical RUSLE soil loss model were used. The R, K and C factors were calculated at monthly scale. The first erosive period extends from July to October and presents the highest values of erosivity (87.8 MJ mm ha−1 h−1), maximum rainfall intensity (22.3 mm h−1) and monthly soil erosion (0.25 Mg ha−1 month−1) with the minimum values of duration of erosive storms, freeze-thaw cycles, soil moisture content and soil erodibility (0.007 Mg h MJ−1 mm−1). This period includes the harvesting and the plowing tillage practices. The second erosive period has a duration of two months, from May to June, and presents the lowest total and monthly soil losses (0.10 Mg ha−1 month−1) that correspond to the maximum protection of the soil by the crop-cover ($C$ factor = 0.05) due to the maximum stage of the growing season and intermediate values of rainfall and runoff erosivity, maximum rainfall intensity and soil erodibility. The third erosive period extends from November to April and has the minimum values of rainfall erosivity (17.5 MJ mm ha−1 h−1) and maximum rainfall intensity (6.0 mm h−1) with the highest number of freeze-thaw cycles, soil moisture content and soil erodibility (0.021 Mg h MJ−1 mm−1) that explain the high value of monthly soil loss (0.24 Mg ha−1 month−1). The interactions between the rainfall erosivity, soil erodibility, and cover-management factors explain the similar predicted soil losses for the first and the third erosive periods in spite of the strong temporal differences in the values of the three RUSLE factors. The estimated value of annual soil loss with the RUSLE model (3.34 Mg ha−1 yr−1) was lower than the measured value with 137Cs (5.38 Mg ha−1 yr−1) due to the low values of precipitation recorded during the studied period. To optimize agricultural practices and to promote sustainable strategies for the preservation of fragile Mediterranean agrosystems it is necessary to delay plowing till October, especially in dryland agriculture regions. Thus, the protective role of the crop residues will extend until September when the greatest rainfall occurs together with the highest runoff erosivity and soil losses.

scholarly journals Effects of Rainfall Intensity and Slope Gradient on Runoff and Soil Moisture Content on Different Growing Stages of Spring Maize

Water ◽  
2015 ◽  
Vol 7 (12) ◽  
pp. 2990-3008 ◽  
Author(s):  
Wenbin Mu ◽  
Fuliang Yu ◽  
Chuanzhe Li ◽  
Yuebo Xie ◽  
Jiyang Tian ◽  
...  
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Rainfall Intensity ◽  
Soil Moisture Content ◽  
Slope Gradient ◽  
Spring Maize

scholarly journals The Influence of a Water Absorbing Geocomposite on Soil Water Retention and Soil Matric Potential

Water ◽  
2019 ◽  
Vol 11 (8) ◽  
pp. 1731 ◽  
Author(s):  
Michał Śpitalniak ◽  
Krzysztof Lejcuś ◽  
Jolanta Dąbrowska ◽  
Daniel Garlikowski ◽  
Adam Bogacz
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Soil Water ◽  
Water Retention ◽  
Soil Moisture Content ◽  
Soil Surface ◽  
Soil Matric Potential ◽  
Soil Water Retention ◽  
Matric Potential ◽  
Control Samples

Climate change induces droughts that are becoming more intensive and more frequent than ever before. Most of the available forecast tools predict a further significant increase in the risk of drought, which indicates the need to prepare solutions to mitigate its effects. Growing water scarcity is now one of the world’s leading challenges. In agriculture and environmental engineering, in order to increase soil water retention, soil additives are used. In this study, the influence of a newly developed water absorbing geocomposite (WAG) on soil water retention and soil matric potential was analyzed. WAG is a special element made from geotextile which is wrapped around a synthetic skeleton with a superabsorbent polymer placed inside. To describe WAG’s influence on soil water retention and soil matric potential, coarse sand, loamy sand, and sandy loam soils were used. WAG in the form of a mat was used in the study as a treatment. Three kinds of samples were prepared for every soil type. Control samples and samples with WAG treatment placed at depths of 10 cm and 20 cm were examined in a test container of 105 × 70 × 50 cm dimensions. The samples had been watered and drained, and afterwards, the soil surface was heated by lamps of 1100 W total power constantly for 72 h. Soil matric potential was measured by Irrometer field tensiometers at three depths. Soil moisture content was recorded at six depths: of 5, 9, 15, 19, 25, and 30 cm under the top of the soil surface with time-domain reflectometry (TDR) measurement devices. The values of soil moisture content and soil matric potential were collected in one-minute steps, and analyzed in 24-h-long time steps: 24, 48, and 72 h. The samples with the WAG treatment lost more water than the control samples. Similarly, lower soil matric potential was noted in the samples with the WAG than in the control samples. However, after taking into account the water retained in the WAG, it appeared that the samples with the WAG had more water easily available for plants than the control samples. It was found that the mechanism of a capillary barrier affected higher water loss from soil layers above those where the WAG had been placed. The obtained results of water loss depend on the soil type used in the profile.

Orthogonal Analysis on the Remediation of Diesel Contaminated Soil by Enhancing Bioventing

2013 ◽  
Vol 807-809 ◽  
pp. 178-183
Author(s):  
Jin Feng Yang ◽  
Cheng Jun Zhang ◽  
Tong Ke Zhao ◽  
Qiong Wu
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Soil Water ◽  
Contaminated Soil ◽  
Pore Volume ◽  
Soil Moisture Content ◽  
High Efficiency ◽  
Orthogonal Experiment ◽  
Volume Number ◽  
Soil Venting

Bioventing is an in situ forced oxidative soil remediation technology which combined soil vapor extraction with biodegradation. It has broad application prospects of soil contamination caused by underground storage tank leakage. Orthogonal experiment as a high efficiency, rapid and economical experimental design method has been widely used in many research. In order to enhance bioventing and shorten the cycle of pollution control,it is necessary to study the mechanism of the interaction among the different factors to quantify the interaction and accelerate the degradation rate. In this study, five factors (initial diesel concentration, venting mode, pore volume number during soil venting, soil moisture content and the ratio of carbon, nitrogen and phosphate) which influence bioventing was chosen to conduct orthogonal experiment of the remediation of diesel contaminated soil by enhancing bioventing. The results show that: 1)Initial diesel concentration and soil moisture content have main effects on the remediation of diesel contaminated soil by bioventing, then the ratio of carbon, nitrogen and phosphate and pore volume number during soil venting. Venting mode has the weakest effect. 2)When 40mg oil/g soil of diesel concentration, air injecting from the bottom of column, 4 vk·d-1 of the pore volume number during soil venting, 100:20:1 of the ratio of carbon, nitrogen and phosphate and soil water content for 20% of the maximum of soil water holding capacity, that would reach a larger removal rate.

Physiological and biochemical responses of Festuca sinensis seedlings to temperature and soil moisture stress

2017 ◽  
Vol 44 (10) ◽  
pp. 1007
Author(s):  
Jian-Jun Wang ◽  
Wei-Hu Lin ◽  
Yan-Ting Zhao ◽  
Cheng Meng ◽  
An-Wei Ma ◽  
...  
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Soil Moisture Content ◽  
Soluble Sugar ◽  
Free Proline ◽  
Relative Water ◽  
Physiological And Biochemical

The interaction effects between temperature and soil moisture on Festuca sinensis Keng ex E.B.Alexeev were analysed to determine how F. sinensis responds to these environmental conditions. A pot experiment was conducted in a greenhouse under simulated growth conditions with four soil moisture contents (80, 65, 50 and 35% relative saturation moisture content) and three temperature conditions (15, 20 and 25°C). Physiological (relative water content and root activity) and biochemical parameters (chlorophyll, peroxidase (POD), malondialdehyde (MDA), soluble protein, soluble sugar and free proline) were evaluated at the seedling stage. Results showed that with a decrease in soil water content, the POD activities, MDA content, soluble protein content, soluble sugar content and free proline content of plants under the 15°C and 20°C treatments initially decreased and then increased, whereas they increased with a decrease of soil water content at 25°C. The relative water contents of plants under the three temperature treatments decreased with a decreasing soil moisture content, but then increased temperature significantly reduced the relative water content of the seedlings under low soil water content. The chlorophyll contents of plants under the 25°C treatment decreased with a decrease of soil moisture content, but those of plants under the 15°C and 20°C treatments initially increased and then decreased. The root activities of plants under the 15°C and 20°C treatments increased with a decreasing soil moisture content; however, those of plants under the 25°C treatment initially increased and then decreased. Thus, results indicated that changes of temperature and soil moisture content had significant and complicated effects on the physiological-biochemical characteristics of F. sinensis; the conditions of 20°C and 65% RSMC had positive effects on F. sinensis seedling growth and the appropriate drought stress could promote the growth of seedling roots under the three different temperature conditions. In conclusion, F. sinensis seedlings could adapt to certain changes in the ecological environment by regulating their physiological and biochemical reactions.

scholarly journals Effects of Biochar and Synthetic Polymer on the Hydro-Physical Properties of Sandy Soils

2018 ◽  
Vol 10 (12) ◽  
pp. 4642 ◽  
Author(s):  
Arafat Alkhasha ◽  
Abdulrasoul Al-Omran ◽  
Anwar Aly
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Physical Properties ◽  
Sandy Soil ◽  
Soil Moisture Content ◽  
Column Experiment ◽  
Field Capacity ◽  
Infiltration Rate ◽  
Arid Environments ◽  
Percentage Decrease

Synthetic polymers, such as polyacrylamide (PAM), and biochar are generally used as soil amendments to improve soil properties. This paper explores a laboratory column experiment conducted to investigate the effects of biochar (pyrolysis at 400–450 °C) and polymers, with different application rates, on the hydro-physical properties of sandy soil. The experiment evaluated four rates each of biochar (0.0% (C), 2% (B1), 4% (B2), 6% (B3) and 8% (B4)) and polymers (0.0% (C), 0.2% (P1), 0.4% (P2), 0.6% (P3), and 0.8%(P4)), as well as a mixture of them. The infiltration rate decreased significantly when a mixture of biochar and polymers was adopted. B1 showed a decrease of 32.73% while a mixture of 8% (B4) and (0.8%) P4 exhibited a decrease of 57.31%. The polymers increased the infiltration rate at low concentrations (P1 and P2) and reduced it at high concentrations (P3 and P4). The cumulative evaporation decreased significantly for most treatments. B1 recorded the highest decrease in cumulative evaporation with a percentage decrease of 31.9%. The highest decrease in hydraulic conductivity (Ks) was for B1. However, the mixture of B4 and P4 resulted in the highest increase in soil moisture content at field capacity compared to the control and other treatments. P4 and the mixture of B2 and P2 showed significant (p < 0.05) increases in the percentage of stable aggregate (SA) in fraction size (0.25–0.125 mm). Although the mixture of B4 and P4 had the highest increase in soil moisture content, this study recommends using the B1 treatment on sandy soil in arid environments due to its strong hydro-physical properties and affordability.

scholarly journals Aspect and soil textural controls on snowmelt runoff on forested Boreal Plain hillslopes

2011 ◽  
Vol 42 (4) ◽  
pp. 250-267 ◽  
Author(s):  
Todd Redding ◽  
Kevin Devito
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Surface Runoff ◽  
Soil Moisture Content ◽  
Mineral Soil ◽  
Sandy Soils ◽  
Slope Aspect ◽  
Snowmelt Runoff ◽  
Near Surface ◽  
Spring Snowmelt

Plot studies were conducted on a jack pine forest with sandy soil and aspen forests with sandy and loam soils to examine the controls of slope aspect, soil texture and fall soil moisture content on near-surface snowmelt runoff and infiltration. It was hypothesized that near-surface runoff would be greater from north-facing slopes on loam soils with increased fall soil moisture content. Fall soil moisture had no measurable effect on spring snowmelt runoff. Infiltration of snowmelt dominated (drainage coefficients 53–100%, median 87%) over near-surface runoff (runoff coefficients 1–65%, median 7%) for most plots. Runoff was related to concrete frost at the mineral soil surface. In contrast to the processes hypothesized, south-facing hillslopes with sandy soils generated greater runoff than north-facing slopes or sites with finer-textured soils. These results were due to greater concrete frost development resulting from periodic spring snowmelt and re-freezing in the upper soil. South-facing hillslopes with sandy soils featured lower canopy cover, allowing greater solar radiation to reach the snow surface which led to the formation of concrete frost and faster melt rates resulting in near-surface runoff. Where hillslopes are connected to receiving surface waters by continuous concrete frost, snowmelt runoff at the watershed scale may be enhanced.

Sign in / Sign up

Export Citation Format

Share Document