scholarly journals Experimental and Numerical Study on the Temperature Elevation in Tissue during Moxibustion Therapy

2020 ◽  
Vol 2020 ◽  
pp. 1-10 ◽  
Author(s):  
Maxim Solovchuk ◽  
Hong-An Deng ◽  
Tony W. H. Sheu
Keyword(s):  
Heat Transfer ◽  
Chinese Medicine ◽  
Moxibustion Therapy ◽  
Numerical Study ◽  
Radiation Heat Transfer ◽  
Three Dimensional ◽  
Skin Surface ◽  
Current Paper ◽  
Measured Temperature ◽  
Temperature Elevation

Moxibustion is a thermal therapy in traditional Chinese medicine that relies on the heat from burning moxa to be transferred beneath the skin surface. Although moxibustion has long been in widespread practice, the mechanism of heat transfer modality and temperature distribution during this treatment is not yet well understood. The current paper presents the first examination by magnetic resonance imaging (MRI) of the three-dimensional temperature elevation during moxibustion treatment. A mathematical model for the prediction of temperature elevation during moxibustion therapy has been constructed and compared with the experimental data. Good agreement between the measured temperature and the results of numerical calculations has been found. Tissue up to 3 cm deep can be heated during the treatment. It was revealed that both heat conduction and radiation heat transfer play important roles during the treatment. The results presented in the current paper can be used for understanding the mechanisms of Chinese medicine and developing useful guidelines for Chinese medicine doctors.

A Numerical Study of the Thermal Performance of a Tape Ball Grid Array (TBGA) Package

1999 ◽  
Vol 122 (2) ◽  
pp. 107-114 ◽  
Author(s):  
Sanjeev B. Sathe ◽  
Bahgat G. Sammakia
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Numerical Study ◽  
Radiation Heat Transfer ◽  
Three Dimensional ◽  
Cover Plate ◽  
Transfer Model ◽  
Turbulence Regime ◽  
Chip Carrier ◽  
Internal Thermal Resistance

This paper deals with the thermal management of a TBGA chip carrier package. In TBGA packages the backside of the chip is available for heat sink or heat spreader (cover plate) attach. By attaching a heat sink directly to the chip and using a thin layer of high thermal conductivity adhesive, a very low internal thermal resistance can be achieved. The package is attached to an organic card and placed vertically in a channel. A three-dimensional conjugate heat transfer model is used, accounting for conduction and radiation in the package and card and convection in the surrounding air. A simplified turbulence model is developed to predict temperatures in the low Re turbulence regime. A parametric study is performed to evaluate the effects of card design, air velocities, interconnect thermal conductivities and thermal radiation on the chip junction temperatures. An experimental study was also conducted to verify the model. Even though the geometry is highly complex due to the multilayer construction of the module and the card, agreement between the model and the experimental measurement is excellent. It was shown that radiation heat transfer can be an equally significant mode as convection in the natural convection regime. [S1043-7398(00)01302-5]

AN EXPERIMENTAL AND NUMERICAL STUDY OF HEAT TRANSFER IN A SIMULATED COLLECTOR FOR A SOLAR DRYER

1993 ◽  
Vol 17 (2) ◽  
pp. 145-160
Author(s):  
P.H. Oosthuizen ◽  
A. Sheriff
Keyword(s):  
Heat Transfer ◽  
Numerical Study ◽  
Local Heat Transfer ◽  
Lower Surface ◽  
Local Heat ◽  
Electrical Heating ◽  
Temperature Profiles ◽  
Measured Temperature ◽  
Transfer Rates ◽  
Thermocouple Probe

Indirect passive solar crop dryers have the potential to considerably reduce the losses that presently occur during drying of some crops in many parts of the “developing” world. The performance so far achieved with such dryers has, however, not proved to be very satisfactory. If this performance is to be improved it is necessary to have an accurate computer model of such dryers to assist in their design. An important element is any dryer model is an accurate equation for the convective heat transfer in the collector. To assist in the development of such an equation, an experimental and numerical study of the collector heat transfer has been undertaken. In the experimental study, the collector was simulated by a 1m long by 1m wide channel with a gap of 4 cm between the upper and lower surfaces. The lower surface of the channel consisted of an aluminium plate with an electrical heating element, simulating the solar heating, bonded to its lower surface. Air was blown through this channel at a measured rate and the temperature profiles at various points along the channel were measured using a shielded thermocouple probe. Local heat transfer rates were then determined from these measured temperature profiles. In the numerical study, the parabolic forms of the governing equations were solved by a forward-marching finite difference procedure.

Numerical Study on the Effect of Inner Tube Position on Heat Transfer Process in Self-Recuperative Radiant Tube

2011 ◽  
Vol 228-229 ◽  
pp. 676-680 ◽  
Author(s):  
Ye Tian ◽  
Xun Liang Liu ◽  
Zhi Wen
Keyword(s):  
Heat Transfer ◽  
Transfer Process ◽  
Numerical Study ◽  
Flame Temperature ◽  
Three Dimensional ◽  
Mathematic Model ◽  
Heat Transfer Process ◽  
Bulk Temperature ◽  
Radiant Tube ◽  
Peak Value

A three-dimensional mathematic model is developed for a 100kw single-end recuperative radiant tube and the simulation is performed with the CFD software FLUENT. Also it is used to investigate the effect of distance between combustion chamber exit and inner tube on heat transfer process. The results suggest that the peak value of combustion flame temperature drops along with the increasing of distance, which leads to low NOX discharging. Also radiant tube surface bulk temperature decreases, which causes radiant tube heating performance losses.

Numerical Simulation of Gas Flow and Heat Transfer in Cross-Wavy Primary Surface Channel for Microtubine Recuperators

2005 ◽  
Author(s):  
H. X. Liang ◽  
Q. W. Wang ◽  
L. Q. Luo ◽  
Z. P. Feng
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Gas Turbine ◽  
Numerical Study ◽  
High Reliability ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Flow And Heat Transfer ◽  
High Heat Transfer ◽  
The Cross

Three-dimensional numerical simulation was conducted to investigate the flow field and heat transfer performance of the Cross-Wavy Primary Surface (CWPS) recuperators for microturbines. Using high-effective compact recuperators to achieve high thermal efficiency is one of the key techniques in the development of microturbine in recent years. Recuperators need to have minimum volume and weight, high reliability and durability. Most important of all, they need to have high thermal-effectiveness and low pressure-losses so that the gas turbine system can achieve high thermal performances. These requirements have attracted some research efforts in designing and implementing low-cost and compact recuperators for gas turbine engines recently. One of the promising techniques to achieve this goal is the so-called primary surface channels with small hydraulic dimensions. In this paper, we conducted a three-dimensional numerical study of flow and heat transfer for the Cross-Wavy Primary Surface (CWPS) channels with two different geometries. In the CWPS configurations the secondary flow is created by means of curved and interrupted surfaces, which may disturb the thermal boundary layers and thus improve the thermal performances of the channels. To facilitate comparison, we chose the identical hydraulic diameters for the above four CWPS channels. Since our experiments on real recuperators showed that the Reynolds number ranges from 150 to 500 under the operating conditions, we implemented all the simulations under laminar flow situations. By analyzing the correlations of Nusselt numbers and friction factors vs. Reynolds numbers of the four CWPS channels, we found that the CWPS channels have superior and comprehensive thermal performance with high compactness, i.e., high heat transfer area to volume ratio, indicating excellent commercialized application in the compact recuperators.

Effect of Periodic Imposed Heat Flux on Three-Dimensional Natural Convection in a Partially Heated Cubical Enclosure

2016 ◽  
Vol 831 ◽  
pp. 83-91
Author(s):  
Lahoucine Belarche ◽  
Btissam Abourida
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Numerical Study ◽  
Control Volume ◽  
Vertical Wall ◽  
Three Dimensional ◽  
Maximum Temperature ◽  
Cubical Enclosure ◽  
Simplec Algorithm ◽  
Volume Method

The three-dimensional numerical study of natural convection in a cubical enclosure, discretely heated, was carried out in this study. Two heating square sections, similar to the integrated electronic components, are placed on the vertical wall of the enclosure. The imposed heating fluxes vary sinusoidally with time, in phase and in opposition of phase. The temperature of the opposite vertical wall is maintained at a cold uniform temperature and the other walls are adiabatic. The governing equations are solved using Control volume method by SIMPLEC algorithm. The sections dimension ε = D / H and the Rayleigh number Ra were fixed respectively at 0,35 and 106. The average heat transfer and the maximum temperature on the active portions will be examined for a given set of the governing parameters, namely the amplitude of the variable temperatures a and their period τp. The obtained results show significant changes in terms of heat transfer, by proper choice of the heating mode and the governing parameters.

Numerical Study on 3D Coupled Heat Transfer of Thrust Chamber with Regenerative Cooling

2011 ◽  
Vol 52-54 ◽  
pp. 1057-1061
Author(s):  
Tao Nie ◽  
Wei Qiang Liu
Keyword(s):  
Heat Transfer ◽  
Optimization Design ◽  
Numerical Study ◽  
Computing Time ◽  
Three Dimensional ◽  
Geometrical Model ◽  
Performance Estimation ◽  
Transfer Model ◽  
Empirical Formulas ◽  
Coupled Heat Transfer

To obtain temperature distribution in regenerative-cooled liquid propellant rocket nozzle quickly and accurately, three-dimensional numerical simulation employed using empirical formulas. A reduced one-dimensional model is employed for the coolant flow and heat transfer, while three dimensional heat transfer model is used to calculate the coupling heat transfer through the wall. The geometrical model is subscale hot-firing chamber. The numerical results agree well with experimental data, while temperature field in nozzle obtained. In terms of computing time and accuracy of results, this method can provide a reference for optimization design and performance estimation.

Numerical Simulations of Heat Transfer and Fluid Flow for a Rotating High-Pressure Turbine

2006 ◽  
Author(s):  
F. Mumic ◽  
L. Ljungkruna ◽  
B. Sunden
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Fluid Flow ◽  
Numerical Study ◽  
Three Dimensional ◽  
Turbulence Models ◽  
High Pressure Turbine ◽  
Experimental Heat ◽  
Commercial Code ◽  
Stator Vane

In this work, a numerical study has been performed to simulate the heat transfer and fluid flow in a transonic high-pressure turbine stator vane passage. Four turbulence models (the Spalart-Allmaras model, the low-Reynolds-number realizable k-ε model, the shear-stress transport (SST) k-ω model and the v2-f model) are used in order to assess the capability of the models to predict the heat transfer and pressure distributions. The simulations are performed using the FLUENT commercial software package, but also two other codes, the in-house code VolSol and the commercial code CFX are used for comparison with FLUENT results. The results of the three-dimensional simulations are compared with experimental heat transfer and aerodynamic results available for the so-called MT1 turbine stage. It is observed that the predictions of the vane pressure field agree well with experimental data, and that the pressure distribution along the profile is not strongly affected by choice of turbulence model. It is also shown that the v2-f model yields the best agreement with the measurements. None of the tested models are able to predict transition correctly.

Sign in / Sign up

Export Citation Format

Share Document