scholarly journals Experimental Study on Mechanical Properties of Fly Ash Stabilized with Cement

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Shengquan Zhou ◽  
Yongfei Zhang ◽  
Dawei Zhou ◽  
Weijian Wang ◽  
Dongwei Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Early Stage ◽  
Strain Curve ◽  
Pozzolanic Reaction ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Compressive Test ◽  
Plastic Properties

Cement-fly ash mixture has been commonly used for the foundation treatment projects in the fly ash stratum, as it is effective in improving foundation bearing capacity and reducing settlement of stratum. In order to figure out the effect of dynamic and static load on the mechanical properties exhibited by the cement-fly ash and the reaction mechanism of cement-fly ash, a combination of the unconfined compressive test, impact test, scanning electron microscopy (SEM), and X-ray diffraction (XRD) method was adopted in this study to investigate the cement-fly ash test samples. As demonstrated by the results, the observed growth rate of 0–60 days (d) is higher than that in the later stages and the typical stress-strain curve can be divided into six sections under the unconfined compressive test. At the gas pressure of 0.2 MPa, the cement-fly ash samples exhibited obvious plastic properties in early curing time (0–60 d), and brittle failure was observed in the final stage (90 d). It is obvious that the value of dynamic compressive strength (DCS) is higher than that of unconfined compressive strength (UCS). The analysis of XRD has revealed that the hydration products are primarily derived from the hydration reaction of cement in the early stage and the pozzolanic reaction in the late stage. The pores of cement-fly ash are found to be filled with the hydration products, despite the presence of a mass of pores in the interior.

scholarly journals Effect of Sodium Aluminate Dosage as a Solid Alkaline Activator on the Properties of Alkali-Activated Slag Paste

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Bin Chen ◽  
Jun Wang ◽  
Jinyou Zhao
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Setting Time ◽  
Sodium Aluminate ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Alkali Activated Slag ◽  
Alkaline Activator ◽  
Activated Slag ◽  
Alkali Activated

Extensive research into alkali-activated slag as a green gel material to substitute for cement has been done because of the advantages of low-carbon dioxide emissions and recycling of industrial solid waste. Alkali-activated slag usually has good mechanical properties, but the too fast setting time restricted its application and promotion. Changing the composition of alkaline activator could optimize setting time, usually making it by adding sodium carbonate or sodium sulfate but this would cause insufficient hydration reaction power and hinder compressive strength growth. In this paper, the effect of sodium aluminate dosage as an alkaline activator on the setting time, fluidity, compressive strength, hydration products, and microstructures was studied through experiments. It is fair to say that an appropriate amount of sodium aluminate could obtain a suitable setting time and better compressive strength. Sodium aluminate provided enough hydroxyl ions for the paste to promote the hydration reaction process that ensured obtaining high compressive strength and soluble aluminium formed precipitate wrapped on the surface of slag to inhibit the hydration reaction process in the early phase that prolonged setting time. The hydration mechanism research found that sodium aluminate played a key role in the formation of higher cross-linked gel hydration products in the late phase of the process. Preparing an alkali-activated slag with excellent mechanical properties and suitable setting time will significantly contribute to its application and promotion.

The Research of Test on Stress-Strain Constitutive Relations of Straw Concrete

2014 ◽  
Vol 584-586 ◽  
pp. 987-992
Author(s):  
Wei Liu ◽  
Wei Xi ◽  
Yi Lu Zhang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Constitutive Relations ◽  
Strain Curve ◽  
Green Building ◽  
Corn Straw ◽  
Stress Strain Curve ◽  
Stress Strain

As a new green building material, straw concrete are introduced about its mechanical properties and characteristics. Mechanical properties test such as prism compressive strength, elastic modulus and Poisson's ratios use standard prismatic blocks. Under different rate of corn straw, cement, sand and fly ash, test gets the full stress-strain curve. Results show that with increase of volume of corn straw, the prism compressive strength reduces significantly. Comparing with natural concrete, elastic modulus of straw concrete can reduces greatly. Poisson’s ratio reduces with increase of volume of corn straw. Fly ash could improve property of the material and replace cement, but excessive replacement will reduce the strength of material.

scholarly journals Mechanical Behavior of Brick Masonry in an Acidic Atmospheric Environment

Materials ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 2694 ◽  
Author(s):  
Shansuo Zheng ◽  
Lihua Niu ◽  
Pei Pei ◽  
Jinqi Dong
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Acid Rain ◽  
Cement Mortar ◽  
Brick Masonry ◽  
Atmospheric Environment ◽  
Peak Strain ◽  
Lime Mortar ◽  
Attenuation Model

In order to evaluate the deterioration regularity for the mechanical properties of brick masonry due to acid rain corrosion, a series of mechanical property tests for mortars, bricks, shear prisms, and compressive prisms after acid rain corrosion were conducted. The apparent morphology and the compressive strength of the masonry materials (cement mortar, cement-lime mortar, cement-fly ash mortar, and brick), the shear behavior of the masonry, and the compression behavior of the masonry were analyzed. The resistance of acid rain corrosion for the cement-lime mortar prisms was the worst, and the incorporation of fly ash into the cement mortar did not improve the acid rain corrosion resistance. The effect of the acid rain corrosion damage on the mechanical properties for the brick was significant. With an increasing number of acid rain corrosion cycles, the compressive strength of the mortar prisms, and the shear and compressive strengths of the brick masonry first increased and then decreased. The peak stress first increased and then decreased whereas the peak strain gradually increased. The slope of the stress-strain curve for the compression prisms gradually decreased. Furthermore, a mathematical degradation model for the compressive strength of the masonry material (cement mortar, cement-lime mortar, cement-fly ash mortar, and brick), as well as the shear strength attenuation model and the compressive strength attenuation model of brick masonry after acid rain corrosion were proposed.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

Microstructure and Mechanical Properties of Ambiently-Cured Blended Coal Ash-Based Geopolymer Concrete

2016 ◽  
Vol 857 ◽  
pp. 400-404
Author(s):  
Tian Yu Xie ◽  
Togay Ozbakkaloglu
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Bottom Ash ◽  
Coal Ash ◽  
Geopolymer Concrete ◽  
Mass Ratio ◽  
Blended Coal ◽  
Microstructure And Mechanical Properties

This paper presents the results of an experimental study on the behavior of fly ash-, bottom ash-, and blended fly and bottom ash-based geopolymer concrete (GPC) cured at ambient temperature. Four bathes of GPC were manufactured to investigate the influence of the fly ash-to-bottom ash mass ratio on the microstructure, compressive strength and elastic modulus of GPC. All the results indicate that the mass ratio of fly ash-to-bottom ash significantly affects the microstructure and mechanical properties of GPCs

Research Progress on the Hydration of Portland Cement with Calcined Clay and Limestone

2021 ◽  
Vol 1036 ◽  
pp. 240-246
Author(s):  
Jin Tang ◽  
Su Hua Ma ◽  
Wei Feng Li ◽  
Hui Yang ◽  
Xiao Dong Shen
Keyword(s):  
Mechanical Properties ◽  
Portland Cement ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Research Progress ◽  
Hydration Reaction ◽  
Hydration Products ◽  
Early Hydration ◽  
Calcined Clay ◽  
Dense Microstructure

The use of calcined clay and limestone as supplementary cementitious materials, can have a certain influence on the hydration of Portland cement. This paper reviewed the influence of limestone and calcined clay and the mixture of limestone and calcined clay on the hydration of cement. Both limestone and calcined clay accelerate the hydration reaction in the early hydration age and enhance the properties of cement. Limestone reacts with C3A to form carboaluminate, which indirectly stabilized the presence of ettringite, while calcined clay consumed portlandite to form C-(A)-S-H gel, additional hydration products promote the densification of pore structure and increase the mechanical properties. The synergistic effect of calcined clay and limestone stabilize the existence of ettringite and stimulate the further formation of carboaluminate, as well as the C-(A)-S-H gel, contributed to a dense microstructure.

Mechanical Properties of Carbon Cathodes during Aluminium Electrolysis

2011 ◽  
Vol 399-401 ◽  
pp. 2155-2159
Author(s):  
Qing Sheng Liu ◽  
Hui Fang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Great Influence ◽  
Strain Curve ◽  
Experimental Simulation ◽  
Ambient Conditions ◽  
Aluminium Electrolysis ◽  
Electrolysis Condition ◽  
Carbon Cathode

Based on the service ambient with aluminium electrolysis condition, the evolution of compressive strength, elastic modulus and stress-strain curve of carbon cathode samples under various conditions are investigated by experimental simulation method; the deterioration mechanism of the mechanical of carbon cathode is also studied. Results show that different carbon cathode materials and ambient conditions have great influence on strength and elastic modulus of carbon cthode. The mechanical properties such as compressive strength and elastic modulus of carbon catodes can be degraded by the erosion of sodium and molten salt during aluminium electrolysis, that has been confirmation by the SEM and XRD analysis.

scholarly journals Characterization and Performance of Mechanical Properties of GGBS Based Geo Polymer Mortars

2019 ◽  
Vol 8 (4) ◽  
pp. 8336-8342
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Construction Industry ◽  
Research Paper ◽  
Setting Times ◽  
And Performance ◽  
Creep And Shrinkage

From decades it has been recognized that Geopolymer will considerably replace the role of cement in the construction industry. In general, Geopolymer exhibits the property of the peak compressive strength, minimal creep and shrinkage. In this current research paper, Geopolymer mortar is prepared by using GGBS and Fly ash. The mix proportions are of (100-60)%GGBS with Fly ash by 10% replacement. The alkali activators Na0H and Na2Sio3 are used in the study for two different molarities of 4&8. The ratio to Sodium silicates to sodium hydroxide is maintained from 1.5, 2, 2.5 & 3 were used. Mortars are prepared and studied the effect of molarities of alkali activators in their setting times and strengths

Research on Barite Concrete Mixed with Fly Ash

2013 ◽  
Vol 275-277 ◽  
pp. 2107-2111
Author(s):  
Qiu Lin Zou ◽  
Jun Li ◽  
Zhen Yu Lai
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Compressive Strength ◽  
High Temperature ◽  
Fly Ash ◽  
Apparent Density ◽  
Cycle Times ◽  
Residual Compressive Strength ◽  
Temperature Performance

Barite concrete with density grade of 3 and strength grade of C30 was prepared by mixing with different fineness of fly ash. The workability, mechanical properties and long-term high temperature performance of the prepared barite concrete were researched. Results show that the workability of barite concrete is improved by mixing with fly ash, and no segregation of mixture has been observed. The apparent density and 3d, 28d compressive strength of barite concrete are decreased obviously after mixing with fly ash. But with the increasing of the fineness of fly ash, the apparent density and 3d, 28d compressive strength of barite concrete have a slight increase. High temperature residual compressive strength is decreased with the increasing of temperature. The cycle times of heat treatment at 400°C only has a little effect on residual compressive strength of barite concrete.

scholarly journals Strength Characteristics of High Strength Concrete (HSC) with and without Coarse Aggregate

2019 ◽  
Vol 9 (2) ◽  
pp. 4701-4704
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Mechanical Characteristics ◽  
Coarse Aggregate ◽  
High Strength ◽  
Set Up

This paper aimed to investigate the mechanical characteristics of HSC of M60 concrete adding 25% of fly ash to cement and sand and percentage variations of silica fumes 0%,5% and 10% to cement with varying sizes of 10mm,6mm,2mm and powder of granite aggregate with w/c of 0.32. Specimens are tested for compressive strength using 10cm X 10cmX10cm cubes for 7,14,28 days flexural strength was determined by using 10cmX10cmX50cm beam specimens at 28 days and 15cm diameter and 30cm height cylinder specimens at 28 days using super plasticizers of conplast 430 as a water reducing agent. In this paper the experimental set up is made to study the mechanical properties of HSC with and without coarse aggregate with varying sizes as 10mm, 6mm, 2mm and powder. Similarly, the effect of silica fume on HSC by varying its percentages as 0%, 5% and 10% in the mix studied. For all mixes 25% extra fly ash has been added for cement and sand.

Sign in / Sign up

Export Citation Format

Share Document