scholarly journals An Investigation of the Effect of Parameters and Chip Slenderness Ratio on Drilling Process Quality of AISI 1050 Steel

2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
Zülküf Demir ◽  
Rifat Yakut
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Thrust Force ◽  
Slenderness Ratio ◽  
Chip Morphology ◽  
Drilling Process ◽  
Steel Alloy ◽  
Drilling Operations ◽  
Machining Operations

The chip slenderness ratio is a vital parameter in theoretical and applicable machining operations. In predrilled drilling operations of AISI 1050 steel alloy, HSS drills were employed, and the effect of the selected parameters on the chip slenderness ratio and also the effect of the chip slenderness ratio on the thrust force, surface roughness, drilled hole delamination, tool wear, and chip morphology were investigated. The major parameters, influential on the chip slenderness ratio, were feed rate and point angle, while spindle speed was too small to be negligible. With increasing the chip slenderness ratio, the thrust force and the tool wear decreased, which resulted in appropriate chip morphology, but there were increases in surface roughness. However, the chip slenderness ratio had no effect on the drilled hole delamination.

Study on ultrasonic-assisted drilling of Ti6Al4V using 3-flute drill in the finite element simulation

2019 ◽  
Vol 234 (7) ◽  
pp. 1298-1310 ◽  
Author(s):  
Peng Wang ◽  
Dazhong Wang
Keyword(s):  
Finite Element ◽  
Tool Wear ◽  
Thrust Force ◽  
Chip Thickness ◽  
Chip Morphology ◽  
Drilling Process ◽  
Wear Depth ◽  
Drill Bit ◽  
Drilling Parameters ◽  
Ultrasonic Assisted

Continuous chip is one of the major problems during drilling Ti6A14V, and chip breaking is dependent on many factors such as drilling parameters, tool geometries and type of drill bits used. This paper attempts to analyze the effect of various drilling parameters such as feed rate, spindle speed on performance characteristics such as chip morphology, thrust force, temperature, and tool wear in conventional drilling and ultrasonic-assisted drilling of Ti6A14V using twist drill bit and 3-flute drill bit in order to optimize the chip breakability of Ti6A14V. The twist and 3-flute drill bit are utilized to establish the finite element models to simulate the drilling process with Lagrangian approach in DEFORM-3D software. The results of the simulations not only reveal obvious varying regular pattern of thrust force, temperature, tool wear depth, chip thickness and damage with the increasing of feed rates, spindle speeds, which confirm the capability and advantage of finite element model of the drilling process, but also provide a more profound knowledge about the drilling mechanism including the effect of 3-flute drill bit in ultrasonic-assisted drilling on chip breakability and tool wear.

scholarly journals An experimental investigation of the effects of point angle on the high-speed steel drills performance in drilling

2018 ◽  
Vol 51 (9-10) ◽  
pp. 417-430 ◽  
Author(s):  
Zülküf Demir
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
High Speed ◽  
Thrust Force ◽  
Cutting Speed ◽  
High Speed Steel ◽  
Dimensional Accuracy ◽  
Cutting Edge ◽  
Drilling Process ◽  
Cutting Speeds

The differences in the cutting speed are a serious problem along the cutting edge of the drill, in drilling operations. This problem can partly be solved reducing the length of the cutting edge via changing the drill point angle. In addition, in this study, the effect of point angle, feed rate, and cutting speed on drilling is investigated. For identifying the optimum cutting parameters, AISI 1050 steel alloy was selected as the experimental specimen, these specimen were pre-drilled 5 mm in diameter due to eliminating the effect of the chisel edge. In the experiments, the holes were drilled only at a depth of 10 mm in order not to give any harm to the dynamometer while measuring thrust force. For this aim, in drilling process, drills with point angle of 100°, 118°, 136°, 154°, and 172° were selected. In conclusion, the thrust force, the tool wear, and the surface roughness linearly decreased with increasing point angles due to less removal chip area, in per revolve of the tool. However, the thrust force, the tool wear, and the surface roughness were adversely affected at higher feed rates and lower cutting speeds. The hole dimensional accuracy decreased at lower feed rates and cutting speeds but at higher point angles and concurrently at higher feed rates but lower point angles and cutting speeds. However, the hole dimensional accuracy showed more decisiveness at 118° than other point angles, while the highest dimensional accuracy values recorded at 136° point angle, at higher cutting speeds.

scholarly journals A Force Sensorless Method for CFRP/Ti Stack Interface Detection during Robotic Orbital Drilling Operations

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Qiang Fang ◽  
Ze-Min Pan ◽  
Bing Han ◽  
Shao-Hua Fei ◽  
Guan-Hua Xu ◽  
...  
Keyword(s):  
Cutting Force ◽  
Thrust Force ◽  
Cutting Parameters ◽  
Force Model ◽  
Drilling Process ◽  
Reinforced Plastics ◽  
Orbital Drilling ◽  
Drilling Parameters ◽  
Drilling Operations ◽  
Machining Properties

Drilling carbon fiber reinforced plastics and titanium (CFRP/Ti) stacks is one of the most important activities in aircraft assembly. It is favorable to use different drilling parameters for each layer due to their dissimilar machining properties. However, large aircraft parts with changing profiles lead to variation of thickness along the profiles, which makes it challenging to adapt the cutting parameters for different materials being drilled. This paper proposes a force sensorless method based on cutting force observer for monitoring the thrust force and identifying the drilling material during the drilling process. The cutting force observer, which is the combination of an adaptive disturbance observer and friction force model, is used to estimate the thrust force. An in-process algorithm is developed to monitor the variation of the thrust force for detecting the stack interface between the CFRP and titanium materials. Robotic orbital drilling experiments have been conducted on CFRP/Ti stacks. The estimate error of the cutting force observer was less than 13%, and the stack interface was detected in 0.25 s (or 0.05 mm) before or after the tool transited it. The results show that the proposed method can successfully detect the CFRP/Ti stack interface for the cutting parameters adaptation.

THRUST FORCE PREDICTION MODEL FOR DRILLING UNIDIRECTIONAL CARBON PLASTICS WITH WEAR OF THE CUTTING TOOL

2021 ◽  
Vol 2 ◽  
pp. 100-108
Author(s):  
V.I. GOLOVIN ◽  
S.YU. RADCHENKO
Keyword(s):  
Carbon Fiber ◽  
Tool Wear ◽  
Prediction Model ◽  
Cutting Tool ◽  
Thrust Force ◽  
Contact Conditions ◽  
Force Prediction ◽  
Geometric Characteristics ◽  
Drill Tool

One of the most important tasks in the production of carbon fiber products is to ensure the specified accuracy and quality of the drilled holes. A model for predicting the thrust force, taking into account the degree of tool wear, is proposed. First, the geometric characteristics of the wear of the spiral drill tool are analyzed. Further, the contact conditions between the drill and the carbon fiber are determined in accordance with the geometric characteristics of the tool wear. Based on the mechanics of the contact interaction of surfaces, the thrust forces of the main cutting edges and the chisel edge are modeled, taking into account the degree of tool wear. The results obtained are integrated into the thrust force prediction model. An example of an experimental study of the drilling carbon fiber is given. The results obtained show a fairly accurate prediction of the cutting force, taking into account the wear of the cutting tool.

Surface characteristics and machining performance of TiAlN-, TiN- and AlCrN-coated tungsten carbide drills

2018 ◽  
Vol 233 (4) ◽  
pp. 1075-1086 ◽  
Author(s):  
Chaiya Dumkum ◽  
Pakin Jaritngam ◽  
Viboon Tangwarodomnukun
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Tungsten Carbide ◽  
Thrust Force ◽  
Surface Characteristics ◽  
Average Error ◽  
Force Model ◽  
Machining Performance ◽  
Coating Materials ◽  
Drilling Performance

This article presents a comprehensive analysis of surface characteristics and drilling performance of uncoated and coated tungsten carbide drills. The single- and double-layer coatings of TiN, TiAlN and AlCrN were examined in terms of surface roughness, microhardness and crack resistance. In addition, drilling torque and thrust force were experimentally measured and compared to the developed models based on the drilling mechanics and drill geometries. Tool wear and hole surface roughness were also considered to assess the machining performance of different coated tools. The results revealed that all coated drills can offer better cut surface quality, 28% lower cutting loads and longer tool life than the uncoated drills. Although AlCrN was found to be the hardest coating material among the others, it caused large wear on the cutting edges and poor surface roughness of produced holes. The lowest torque and thrust force were achievable using TiN-coated drill, while the use of TiAlN coating resulted in the lowest surface roughness and smallest tool wear. Furthermore, the drilling torque and thrust force model developed in this study were found to correspond to the experimental measures with the average error of 8.4%. The findings of this work could facilitate the selection of coating materials to advance the machining performance.

ANALYSIS OF THE CORRELATION BETWEEN FRACTAL STRUCTURE OF CUTTING FORCE SIGNAL AND SURFACE ROUGHNESS OF MACHINED WORKPIECE IN END MILLING OPERATION

Fractals ◽  
2019 ◽  
Vol 27 (02) ◽  
pp. 1950013 ◽  
Author(s):  
AHMAD THUFFAIL THASTHAKEER ◽  
ALI AKHAVAN FARID ◽  
CHANG TECK SENG ◽  
HAMIDREZA NAMAZI
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Surface Quality ◽  
Cutting Forces ◽  
End Milling ◽  
Complex Structure ◽  
Machined Surface ◽  
End Mills ◽  
Machining Operations

Analysis of the machined surface is one of the major issues in machining operations. On the other hand, investigating about the variations of cutting forces in machining operation has great importance. Since variations of cutting forces affect the surface quality of machined workpiece, therefore, analysis of the correlation between cutting forces and surface roughness of machined workpiece is very important. In this paper, we employ fractal analysis in order to investigate about the complex structure of cutting forces and relate them to the surface quality of machined workpiece. The experiments have been conducted in different conditions that were selected based on cutting depths, type of cutting tool (serrated versus. square end mills) and machining conditions (wet and dry machining). The result of analysis showed that among all comparisons, we could only see the correlation between complex structure of cutting force and the surface roughness of machined workpiece in case of using serrated end mill in wet machining condition. The employed methodology in this research can be widely applied to other types of machining operations to analyze the effect of variations of different parameters on variability of cutting forces and surface roughness of machined workpiece and then investigate about their correlation.

Drilling Force and Chip Morphology in Drilling of PCB Supported Hole

2011 ◽  
Vol 188 ◽  
pp. 429-434 ◽  
Author(s):  
L.P. Yang ◽  
Li Xin Huang ◽  
Cheng Yong Wang ◽  
L.J. Zheng ◽  
Ping Ma ◽  
...  
Keyword(s):  
Feed Rate ◽  
Printed Circuit Board ◽  
Thrust Force ◽  
Chip Morphology ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Circuit Board ◽  
Drilling Process ◽  
Drilling Force ◽  
Drill Bits

Supported holes of Printed circuit board (PCB) are drilled with two different drill bits. Drilling force (thrust force and torque) and chip morphology are examined at different cutting parameters, and the effects of the two drills are discussed. The results indicate that the drilling force and chip morphology are affected by the feed rate, spindle speed and drill shape. Thrust force increases with the increasing feed rate, and decreases with the increasing spindle speed. Optimization of drill geometry can reduce the thrust force significantly, and is effective in chip breaking which can improve the chip evacuation during the drilling process.

The effect of monolayer TiCN-, AlTiN-, TiAlN-and two layers TiCN + TiN- and AlTiN + TiN-coated cutting tools on tool wear, cutting force, surface roughness and chip morphology during high-speed milling of Ti6Al4V titanium alloy

2016 ◽  
Vol 232 (7) ◽  
pp. 1273-1286 ◽  
Author(s):  
Emel Kuram
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Tool Wear ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Tools ◽  
Chip Morphology ◽  
High Speed Milling ◽  
Ti6al4v Titanium Alloy ◽  
Coated Carbide

Tool coatings can improve the machinability performance of difficult-to-cut materials such as titanium alloys. Therefore, in the current work, high-speed milling of Ti6Al4V titanium alloy was carried out to determine the performance of various coated cutting tools. Five types of coated carbide inserts – monolayer TiCN, AlTiN, TiAlN and two layers TiCN + TiN and AlTiN + TiN, which were deposited by physical vapour deposition – were employed in the experiments. Tool wear, cutting force, surface roughness and chip morphology were evaluated and compared for different coated tools. To understand the tool wear modes and mechanisms, detailed scanning electron microscope analysis combined with energy dispersive X-ray of the worn inserts were conducted. Abrasion, adhesion, chipping and mechanical crack on flank face and coating delamination, adhesion and crater wear on rake face were observed during high-speed milling of Ti6Al4V titanium alloy. In terms of tool wear, the lowest value was obtained with TiCN-coated insert. It was also found that at the beginning of the machining pass TiAlN-coated insert and at the end of machining TiCN-coated insert gave the lowest cutting force and surface roughness values. No change in chip morphology was observed with different coated inserts.

Research on the Effect of Low Temperature on the Performance of Drilling Carbon Fibre Reinforced Polymer and Ti Stack Materials

2012 ◽  
Vol 723 ◽  
pp. 30-34 ◽  
Author(s):  
Xi Wang ◽  
Cheng Yong Wang ◽  
Run Ping Shi ◽  
Yue Xian Song ◽  
Ying Ning Hu
Keyword(s):  
Low Temperature ◽  
Tool Wear ◽  
Thrust Force ◽  
Fiber Reinforced Polymer ◽  
Drilling Force ◽  
Reinforced Polymer ◽  
Drilling Temperature ◽  
Carbon Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer

The thermal conductivity of carbon fiber reinforced polymer(CFRP) and titanium alloy is lower which caused the increasing of drilling temperature and larger tool wear resistance. The low temperature air is aided for the drilling of laminated stack board of CFRP/Ti with double apex angles carbide drill at different feed rate. The drilling force and the quality of hole are analyzed. The results showed that the low temperature air can reduce the tool wear and the thrust force effectively.

Sign in / Sign up

Export Citation Format

Share Document