scholarly journals Experimental and Theoretical Study of Gear Dynamical Transmission Characteristic Considering Measured Manufacturing Errors

2018 ◽  
Vol 2018 ◽  
pp. 1-20 ◽  
Author(s):  
Fang Guo ◽  
Zongde Fang
Keyword(s):  
Transmission Error ◽  
Helical Gear ◽  
Tooth Surface ◽  
Time Varying ◽  
Mesh Stiffness ◽  
Tooth Contact Analysis ◽  
Gear Mesh ◽  
Manufacturing Errors ◽  
Tooth Modification ◽  
Helical Gear Pair

In the research of gear transmission, the vibration and noise problem has received many concerns all the times. Scholars use tooth modification technique to improve the meshing state of gearings in order to reduce the vibration and noise. However, few of researchers consider the influence of measured manufacturing errors when they do the study of tooth modification. In order to investigate the efficiency of the tooth modification in the actual project, this paper proposes a dynamic model of a helical gear pair including tooth modification and measured manufacturing errors to do a deterministic analysis on the dynamical transmission performance. In this analysis, based on the measured tooth deviation, a real tooth surface (including modification and measured tooth profile error) is fitted by a bicubic B-spline. With the tooth contact analysis (TCA) and loaded tooth contact analysis (LTCA) on the real tooth surface, the loaded transmission error, tooth surface elastic deformation, and load distribution can be determined. Based on the results, the time-varying mesh stiffness and gear mesh impact are computed. Taking the loaded transmission error, measured cumulative pitch error, eccentricity error, time-varying mesh stiffness, and gear mesh impact as the internal excitations, this paper establishes a 12-degree-of-freedom (DOF) dynamic model of a helical gear pair and uses the Fourier series method to solve it. In two situations of low speed and high speed, the gear system dynamic response is analyzed in the time and frequency domains. In addition, an experiment is performed to validate the simulation results. The study shows that the proposed technique is useful and reliable for predicting the dynamic response of a gear system.

Vibration-based fault diagnosis of helical gear pair with tooth surface wear considering time-varying friction coefficient under mixed EHL condition

2021 ◽  
pp. 1-16
Author(s):  
Siyu Wang ◽  
Rupeng Zhu
Keyword(s):  
Dynamic Response ◽  
Hydrodynamic Lubrication ◽  
Helical Gear ◽  
Calculation Model ◽  
Tooth Surface ◽  
Time Varying ◽  
Gear Pair ◽  
Surface Wear ◽  
Mesh Stiffness ◽  
Helical Gear Pair

Abstract Based on “slice method”, the improved time-varying mesh stiffness (TVMS) calculation model of helical gear pair with tooth surface wear is proposed, in which the effect of friction force that obtained under mixed elasto-hydrodynamic lubrication (EHL) is considered in the model. Based on the improved TVMS calculation model, the dynamic model of helical gear system is established, then the influence of tooth wear parameters on the dynamic response is studied. The results illustrate that the varying reduction extents of mesh stiffness along tooth profile under tooth surface wear, in addition, the dynamic response in time-domain and frequency-domain present significant decline in amplitude under deteriorating wear condition.

scholarly journals Geometry Modification of Helical Gear for Reduction of Static Transmission Error

2018 ◽  
Vol 167 ◽  
pp. 02013
Author(s):  
Jeonghyun Park ◽  
Changjun Seo ◽  
Kwangsuck Boo ◽  
Heungseob Kim
Keyword(s):  
Transmission Error ◽  
Helical Gear ◽  
Necessary Condition ◽  
Mesh Stiffness ◽  
Profile Modification ◽  
Gear Mesh ◽  
Static Transmission Error ◽  
Excitation Mechanisms ◽  
Gear Systems ◽  
Gear Mesh Stiffness

Gear systems are extensively employed in mechanical systems since they allow the transfer of power with a variety of gear ratios. So gears cause the inherent deflections and deformations due to the high pressure which occurs between the meshing teeth when transmit power and results in the transmission error. It is usually assumed that the transmission error and variation of the gear mesh stiffness are the dominant excitation mechanisms. Predicting the static transmission error is a necessary condition to reduce noise radiated from the gear systems. This paper aims to investigate the effect of tooth profile modifications on the transmission error of helical gear. The contact stress analysis was implemented for different roll positions to find out the most critical roll angle in view point of root flank stress. The PPTE (peak-to-peak of transmission error) is estimated at the roll angles by different loading conditions with two dimensional FEM. The optimal profile modification from the root to the tip is proposed.

scholarly journals Dynamic Model of Spur Gear Pair with Modulation Internal Excitation

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Zhong Wang ◽  
Lei Zhang ◽  
Yuan-Qing Luo ◽  
Chang-Zheng Chen
Keyword(s):  
Dynamic Model ◽  
Transmission Error ◽  
Spur Gear ◽  
Experimental Result ◽  
Time Varying ◽  
Gear Pair ◽  
Mesh Stiffness ◽  
Gear Mesh ◽  
Internal Excitation ◽  
Modulation Sideband

In the actual measurements, vibration and noise spectrum of gear pair often exhibits sidebands around the gear mesh harmonic orders. In this study, a nonlinear time-varying dynamic model of spur gear pair was established to predict the modulation sidebands caused by the AM-FM modulation internal excitation. Here, backlash, modulation time-varying mesh stiffness, and modulation transmission error are considered. Then the undamped natural mode was studied. Numerical simulation was made to reveal the dynamic characteristic of a spur gear under modulation condition. The internal excitation was shown to exhibit obvious modulation sideband because of the modulation time-varying mesh stiffness and modulation transmission error. The Runge-Kutta method was used to solve the equations for analyzing the dynamic characteristics with the effect of modulation internal excitation. The result revealed that the response under modulation excitation exhibited obvious modulation sideband. The response under nonmodulation condition was also calculated for comparison. In addition, an experiment was done to verify the prediction of the modulation sidebands. The calculated result was consistent with the experimental result.

An Analytical Investigation of Rattle Characteristics of Powder Metal Gears

2019 ◽  
Author(s):  
Elizabeth Slavkovsky ◽  
Murat Inalpolat ◽  
Anders Flodin
Keyword(s):  
Transmission Error ◽  
Analytical Investigation ◽  
Time Varying ◽  
Evaluation Tool ◽  
Mesh Stiffness ◽  
Gear Design ◽  
Gear Mesh ◽  
Internal Excitation ◽  
Gear Mesh Stiffness ◽  
Gear Rattle

Abstract This study employs an analytical model of a gear pair with transverse-torsional dynamics that allows analysis of single-sided, double-sided, and random rattle situations to contrast rattle characteristics of isotropic PM gears with a baseline steel gearset. This model utilizes time-varying gear mesh stiffness and transmission error as the internal excitation sources and time-varying operating torque as an external excitation. The gear rattle performance of PM gears is investigated under different torque conditions and operating speeds. The system kinetic and potential energy is assessed as an evaluation tool that can indicate the severity of different rattle conditions. The dynamic response of two different versions of an existing PM gear design are compared with a baseline traditional steel gear.

Using variable modulus to modify a rack cutter and generate a gear pair

2022 ◽  
pp. 095440622110617
Author(s):  
Yang Hsueh-Cheng ◽  
Zhong-Wei Huang
Keyword(s):  
Helical Gear ◽  
Tooth Surface ◽  
Gear Pair ◽  
Tooth Contact Analysis ◽  
Parabolic Profile ◽  
Face Width ◽  
Variable Modulus ◽  
The Face ◽  
Helical Gear Pair ◽  
Assembly Error

In this paper, two normal imaginary helical rack cutters were first established. One of these cutters is a skewed-rack cutter with an asymmetrical straight edge. The other is a rack cutter with an asymmetric parabolic profile. Second, the gear’s tooth surface of the asymmetric parabolic rack cutter is modified to be barrel-shaped based on a variable modulus. The tooth thickness of the gear is gradually reduced along the face width of the tooth from the middle of the tooth surface. Then the coordinate relationship between the gears’ blanks and the imaginary helical rack cutters was established. Through the differential geometry, crowned and uncrowned helical gear pairs were generated. Because of human factors, when the gear pair is installed, it is easy to cause the gear pair edge contact. It is necessary to add artificial assembly error settings through the tooth contact analysis to investigate the kinematic errors and contact conditions of the crowned and uncrowned helical gear pair. The mathematical models and analysis methods proposed for the crowned imaginary rack cutter using variable modulus should be useful for the design and production of double crowned helical gears with asymmetric parabolic teeth.

A parameterized numerical model for the evaluation of gear mesh stiffness variation of a helical gear pair

2008 ◽  
Vol 222 (7) ◽  
pp. 1321-1327 ◽  
Author(s):  
J Hedlund ◽  
A Lehtovaara
Keyword(s):  
Numerical Model ◽  
Transmission Error ◽  
Helical Gear ◽  
Hertzian Contact ◽  
Mesh Stiffness ◽  
Fe Method ◽  
Gear Design ◽  
Gear Mesh ◽  
Stiffness Variation ◽  
Gear Mesh Stiffness

One of the most common challenges in gear drive design is to determine the best combination of gear geometry parameters. These parameters should be capable of being varied effectively and related to gear mesh stiffness variation in advanced excitation and vibration analysis. Accurate prediction of gear mesh stiffness and transmission error requires an efficient numerical method. The parameterized numerical model was developed for the evaluation of excitation induced by mesh stiffness variation for helical gear design purposes. The model uses linear finite-element (FE) method to calculate tooth deflections, including tooth foundation flexibility. The model combines Hertzian contact analysis with structural analysis to avoid large FE meshes. Thus, mesh stiffness variation was obtained in the time and frequency domains, which gives flexibility if comparison is made with measured spectrums. Calculations showed that a fairly low number of elements suffice for the estimation of mesh stiffness variation. A reasonable compromise was achieved between design trends and calculation time.

A model for analyzing stiffness and stress in a helical gear pair with tooth profile errors

2016 ◽  
Vol 23 (2) ◽  
pp. 272-289 ◽  
Author(s):  
Qibin Wang ◽  
Yimin Zhang
Keyword(s):  
Contact Stress ◽  
Transmission Error ◽  
Helical Gear ◽  
Tooth Root ◽  
Mesh Stiffness ◽  
Tooth Contact ◽  
Gear Mesh ◽  
Profile Errors ◽  
Gear Mesh Stiffness ◽  
Root Stress

A model is introduced for analyzing the influence of tooth shape deviations and assembly errors on the helical gear mesh stiffness, loaded transmission error, tooth contact stress and tooth root stress. The helical gear is approximated as a series of independent spur gear slices along axial direction whose face-width is relatively small. The relative position relationships among those sliced teeth in mesh are developed with tooth profile errors and the stiffness of the sliced tooth is calculated by the potential energy method. From the equilibriums of the forces, gear mesh stiffness, loaded transmission error, tooth contact stress and tooth root stress are calculated. Then two cases are presented for validation of the model. It is demonstrated that the model is effective for calculating the stiffness of helical gear pairs. Finally, the effects of the tooth tip reliefs, lead crown reliefs and misalignments on the gear mesh stiffness, transmission error, tooth contact stress and tooth root stress are analyzed. The results show that mesh stiffness decreases, loaded transmission error, the maximum tooth contact stress and the maximum tooth root stress grow with the increasing tooth tip relief, lead crown relief and misalignment. And tooth edge has concentrated tooth contact stresses with a gear misalignment.

Sign in / Sign up

Export Citation Format

Share Document