scholarly journals Computer Numerical Controlled Grinding and Physical Vapor Deposition for Fused Deposition Modelled Workpieces

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Fulvio Lavecchia ◽  
Gianluca Percoco ◽  
Eujin Pei ◽  
Luigi Maria Galantucci
Keyword(s):  
Vapor Deposition ◽  
Physical Vapor Deposition ◽  
High Surface ◽  
Extrusion Process ◽  
Surface Finishing ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Test Pieces ◽  
Pvd Coating

The use of additive manufacturing (AM) enables companies to directly produce complex end-use parts. Fused deposition modelling (FDM) is an AM technology based on an extrusion process of fabricating parts. This layer-by-layer method results in a poor surface finish, and as a result, manual finishing is often required, which consequentially reduces the definition of the geometrical features. This research proposes a novel way of achieving high surface finishing by using additive and finishing processes, followed by a physical vapor deposition (PVD) coating. Two test pieces were produced, the first one was subjected to computer numerical controlled (CNC) mechanical grinding with appropriate grades of grindstones; the second one was subjected to microsandblasting to remove excess material and the stair-stepping effect. Both test pieces were then subjected to a PVD coating process to provide a metal thin film. To benchmark the test pieces, the authors used a coordinate measure machine for dimensions and a roughness meter to verify the effectiveness of this postprocessing approach.

Evaluation of geometrical benchmark artifacts containing multiple overhang lengths fabricated using material extrusion technique

2020 ◽  
Vol 14 (3) ◽  
pp. 7296-7308
Author(s):  
Siti Nur Humaira Mazlan ◽  
Aini Zuhra Abdul Kadir ◽  
N. H. A. Ngadiman ◽  
M.R. Alkahari
Keyword(s):  
3D Model ◽  
Laser Scanner ◽  
Dimensional Accuracy ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Layer Technique ◽  
Subtractive Manufacturing ◽  
Manufacturing Features ◽  
Layer Problem

Fused deposition modelling (FDM) is a process of joining materials based on material entrusion technique to produce objects from 3D model using layer-by-layer technique as opposed to subtractive manufacturing. However, many challenges arise in the FDM-printed part such as warping, first layer problem and elephant food that was led to an error in dimensional accuracy of the printed parts especially for the overhanging parts. Hence, in order to investigate the manufacturability of the FDM printed part, various geometrical and manufacturing features were developed using the benchmarking artifacts. Therefore, in this study, new benchmarking artifacts containing multiple overhang lengths were proposed. After the benchmarking artifacts were developed, each of the features were inspected using 3D laser scanner to measure the dimensional accuracy and tolerances. Based on 3D scanned parts, 80% of the fabricated parts were fabricated within ±0.5 mm of dimensional accuracy as compared with the CAD data. In addition, the multiple overhang lengths were also successfully fabricated with a very significant of filament sagging observed.

scholarly journals Fused Deposition Modelling of Fibre Reinforced Polymer Composites: A Parametric Review

2021 ◽  
Vol 5 (1) ◽  
pp. 29
Author(s):  
Narongkorn Krajangsawasdi ◽  
Lourens G. Blok ◽  
Ian Hamerton ◽  
Marco L. Longana ◽  
Benjamin K. S. Woods ◽  
...  
Keyword(s):  
Process Parameters ◽  
Mechanical Performance ◽  
Fibre Length ◽  
Processing Parameters ◽  
Thermoplastic Composite ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Fibre Reinforced Polymer ◽  
Printing Parameters

Fused deposition modelling (FDM) is a widely used additive layer manufacturing process that deposits thermoplastic material layer-by-layer to produce complex geometries within a short time. Increasingly, fibres are being used to reinforce thermoplastic filaments to improve mechanical performance. This paper reviews the available literature on fibre reinforced FDM to investigate how the mechanical, physical, and thermal properties of 3D-printed fibre reinforced thermoplastic composite materials are affected by printing parameters (e.g., printing speed, temperature, building principle, etc.) and constitutive materials properties, i.e., polymeric matrices, reinforcements, and additional materials. In particular, the reinforcement fibres are categorized in this review considering the different available types (e.g., carbon, glass, aramid, and natural), and obtainable architectures divided accordingly to the fibre length (nano, short, and continuous). The review attempts to distil the optimum processing parameters that could be deduced from across different studies by presenting graphically the relationship between process parameters and properties. This publication benefits the material developer who is investigating the process parameters to optimize the printing parameters of novel materials or looking for a good constituent combination to produce composite FDM filaments, thus helping to reduce material wastage and experimental time.

scholarly journals CVD and PVD coating process modelling by using artificial neural networks

2012 ◽  
Vol 1 (1) ◽  
pp. 46 ◽  
Author(s):  
Amir Mahyar Khorasani ◽  
Mohammad Reza Solymany yazdi ◽  
Mehdi Faraji ◽  
Alex Kootsookos
Keyword(s):  
Thin Film ◽  
Vapor Deposition ◽  
Physical Vapor Deposition ◽  
Chemical Vapor ◽  
Film Coating ◽  
Deposition Process ◽  
Thin Film Coating ◽  
Mlp Neural Network ◽  
Titanium Thin Film ◽  
Pvd Coating

Thin-film coating plays a prominent role on the manufacture of many industrial devices. Coating can increase material performance due to the deposition process. Having adequate and precise model that can predict the hardness of PVD and CVD processes is so helpful for manufacturers and engineers to choose suitable parameters in order to obtain the best hardness and decreasing cost and time of industrial productions. This paper proposes the estimation of hardness of titanium thin-film layers as protective industrial tools by using multi-layer perceptron (MLP) neural network. Based on the experimental data that was obtained during the process of chemical vapor deposition (CVD) and physical vapor deposition (PVD), the modeling of the coating variables for predicting hardness of titanium thin-film layers, is performed. Then, the obtained results are experimentally verified and very accurate outcomes had been attained.

Performance of Low-Cost 3D Printer in Medical Application

2021 ◽  
Author(s):  
Nor Aiman Sukindar ◽  
Azib Azhari Awang Dahan ◽  
Sharifah Imihezri Syed Shaharuddin ◽  
Nor Farah Huda Abd Halim
Keyword(s):  
Low Cost ◽  
Medical Application ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Layer By Layer ◽  
Total Deformation ◽  
Element Analysis ◽  
Porosity Level ◽  
Fused Deposition ◽  
Printing Parameters

Abstract Fused Deposition Modelling (FDM) is an additive manufacturing (AM) process that produces a physical object directly from a CAD design using layer-by-layer deposition of the filament material that is extruded via a nozzle. In industry, FDM has become one of the most used AM processes for the production of low batch quantity and functional prototypes, due to its safety, efficiency, reliability, low cost, and ability to process manufacturing-grade engineering thermoplastic. Recently, the market is flooded with the availability of low-cost printers produced by numerous companies. This research aims to investigate the effect of different porosity levels on a scaffold structure produced using a low-cost 3D printer. Comparisons of these porous structures were made in terms of Von-Mises strain, total deformation, as well as compressive stress. Various porosity levels were created by varying printing parameters, including layer height, infill density, and shell thickness by slicing the initial solid CAD file using Repetier Host 3D printing software. Finite Element Analysis (FEA) simulation was then performed on the created scaffold structures by using Ansys Workbench 19.2. The simulation result indicates that the greater porosity level will result in higher total deformation of the structure. Meanwhile, the compression test shows that the minimum strength value obtained was favourable at 22 MPa and had exceeded that of the trabecular femur (15 MPa). However, its porosity level (maximum at 52%) was still below that of the minimum threshold of porosity level of 70 percent. However, the printing parameters currently used can be adjusted in the future. Therefore, it was deduced that the low-cost 3D printer offers promising potential to fabricate different porosity structures with multiple outcomes.

Thermomechanical investigations of PEKK-HAp-CS composites

2019 ◽  
Vol 233 (11) ◽  
pp. 1196-1203
Author(s):  
Rupinder Singh ◽  
Gurchetan Singh ◽  
Jaskaran Singh ◽  
Ranvijay Kumar ◽  
Md Mustafizur Rahman ◽  
...  
Keyword(s):  
Melt Flow Index ◽  
Extrusion Process ◽  
Flow Index ◽  
Fused Deposition Modelling ◽  
Index Test ◽  
Melt Flow ◽  
Scanning Calorimetry ◽  
Fused Deposition ◽  
Ether Ketone ◽  
Input Variables

In this experimental study, a composite of poly-ether-ketone-ketone by reinforcement of hydroxyapatite and chitosan has been prepared for possible applications as orthopaedic scaffolds. Initially, different weight percentages of hydroxyapatite and chitosan were reinforced in the poly-ether-ketone-ketone matrix and tested for melt flow index in order to check the flowability of different compositions/proportions. Suitable compositions revealed by the melt flow index test were then taken forward for the extrusion of filament required for fused deposition modelling. For thermomechanical investigations, Taguchi-based design of experiments has been used with input variables in the extrusion process as follows: temperature, load applied and different composition/proportions. The specimens in the form of feedstock filament produced by the extrusion process were made to undergo tensile testing. The specimens were also inspected by differential scanning calorimetry and photomicrographs. Finally, the specimen showing the best performance from the thermomechanical viewpoint has been selected to extrude the filament for the fused deposition modelling process.

scholarly journals Investigation of a Short Carbon Fibre-Reinforced Polyamide and Comparison of Two Manufacturing Processes: Fused Deposition Modelling (FDM) and Polymer Injection Moulding (PIM)

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 672 ◽  
Author(s):  
Elena Verdejo de Toro ◽  
Juana Coello Sobrino ◽  
Alberto Martínez Martínez ◽  
Valentín Miguel Eguía ◽  
Jorge Ayllón Pérez
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Injection Moulding ◽  
New Technologies ◽  
Mechanical Response ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Polymer Injection ◽  
Fused Deposition

New technologies are offering progressively more effective alternatives to traditional ones. Additive Manufacturing (AM) is gaining importance in fields related to design, manufacturing, engineering and medicine, especially in applications which require complex geometries. Fused Deposition Modelling (FDM) is framed within AM as a technology in which, due to their layer-by-layer deposition, thermoplastic polymers are used for manufacturing parts with a high degree of accuracy and minimum material waste during the process. The traditional technology corresponding to FDM is Polymer Injection Moulding, in which polymeric pellets are injected by pressure into a mould using the required geometry. The increasing use of PA6 in Additive Manufacturing makes it necessary to study the possibility of replacing certain parts manufactured by injection moulding with those created using FDM. In this work, PA6 was selected due to its higher mechanical properties in comparison with PA12. Moreover, its higher melting point has been a limitation for 3D printing technology, and a further study of composites made of PA6 using 3D printing processes is needed. Nevertheless, analysis of the mechanical response of standardised samples and the influence of the manufacturing process on the polyamide’s mechanical properties needs to be carried out. In this work, a comparative study between the two processes was conducted, and conclusions were drawn from an engineering perspective.

scholarly journals Tensile Mechanical Behaviour of Multi-Polymer Sandwich Structures via Fused Deposition Modelling

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 651 ◽  
Author(s):  
David Moises Baca Lopez ◽  
Rafiq Ahmad
Keyword(s):  
Mechanical Properties ◽  
Low Cost ◽  
Acrylonitrile Butadiene Styrene ◽  
Extrusion Process ◽  
Poly Lactic Acid ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Homogeneous Materials ◽  
Flexural Tests ◽  
High Level

The application of single homogeneous materials produced through the fused deposition modelling (FDM) technology restricts the production of high-level multi-material components. The fabrication of a sandwich-structured specimen with different material combinations using conventional thermoplastics such as poly (lactic acid) (PLA), acrylonitrile butadiene styrene (ABS) and high impact polystyrene (HIPS) through the filament-based extrusion process can demonstrate an improvement on its properties. This paper aims to assess among these materials, the best material sandwich-structured arrangement design, to enhance the mechanical properties of a part and to compare the results with the homogeneous materials selected. The samples were subjected to tensile testing to identify the tensile strength, elongation at break and Young’s modulus of each material combination. The experimental results demonstrate that applying the PLA-ABS-PLA sandwich arrangement leads to the best mechanical properties between these materials. This study enables users to consider sandwich structure designs as an alternative to manufacturing multi-material components using conventional and low-cost materials. Future work will consider the flexural tests to identify the maximum stresses and bending forces under pressure.

Anisotropy Evaluation of Different Raster Directions, Spatial Orientations, and Fill Percentage of 3D Printed PETG Tensile Test Specimens

2019 ◽  
Vol 821 ◽  
pp. 167-173 ◽  
Author(s):  
Muammel M. Hanon ◽  
Róbert Marczis ◽  
László Zsidai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Tensile Test ◽  
Fused Deposition Modelling ◽  
Elongation At Break ◽  
Know How ◽  
Fused Deposition ◽  
Test Pieces ◽  
3D Printed ◽  
Fill Percentage

In this paper, the mechanical properties of Polyethylene terephthalate-glycol (PETG) tensile test specimens have been investigated. The test pieces were prepared using fused deposition modelling (FDM) 3D printing technology. Three print settings were examined which are: raster direction angles, print orientations, and infill percentage and patterns in order to evaluate the anisotropy of objects when employing FDM print method. The variations in stress-strain curves, tensile strength values and elongation at break among the tested samples were studied and compared. Illustration for the broken specimens after the tensile test was accomplished to know how the test pieces printed with various parameters were fractured. A comparison with some previous results regarding the elongation at break has been carried out.

Effects of Build Orientations on Tensile Properties of PLA Material Processed by FDM

2014 ◽  
Vol 1044-1045 ◽  
pp. 31-34 ◽  
Author(s):  
Mst Faujiya Afrose ◽  
S.H. Masood ◽  
Mostafa Nikzad ◽  
Pio Iovenitti
Keyword(s):  
Tensile Properties ◽  
Low Cost ◽  
Testing Machine ◽  
Extrusion Process ◽  
Fused Deposition Modelling ◽  
Tensile Testing Machine ◽  
Thermoplastic Material ◽  
Fused Deposition ◽  
Dog Bone ◽  
3D Printers

Fused Deposition Modelling (FDM) of thermoplastic materials is generally a well-known technology among all additive manufacturing (AM) technologies and therefore, it is essential to investigate the mechanical properties of such FDM processed materials. Several open-source and low cost AM machines, known as 3D Printers, have recently been developed using thermoplastic extrusion process based on the original FDM technology. Many of these 3D Printers use Polylactic Acid (PLA) plastic for building parts. The main objective of this paper is to investigate the tensile properties of the PLA thermoplastic material processed by the Cube-2 3D Printer. In this study, the dog-bone sized PLA specimens are printed in different build orientations and a Zwick Z010 tensile testing machine is used to determine the tensile properties of PLA in different build orientation.

Sign in / Sign up

Export Citation Format

Share Document