scholarly journals Investigation of Performance and Residual Stress Generation of AlSi10Mg Processed by Selective Laser Melting

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Lianfeng Wang ◽  
Xiaohui Jiang ◽  
Yihong Zhu ◽  
Zishan Ding ◽  
Xiaogang Zhu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Residual Stresses ◽  
Selective Laser Melting ◽  
Tilt Angle ◽  
Side Surface ◽  
Stress Generation ◽  
Laser Melting ◽  
Scanning Strategy ◽  
Preheating Temperature

During the selective laser melting (SLM) process, the scanned layers are subjected to rapid thermal cycles. By working on the mechanical properties, residual stress, and microstructure, the high-temperature gradients can have significant effect on the proper functioning and the structural integrity of built parts. This work presents a comprehensive study on the scanning path type and preheating temperature for AlSi10Mg alloy during SLM. According to the results, SLM AlSi10Mg parts fabricated in chessboard scanning strategy have higher mechanical properties or at least comparable to the parts fabricated in uniformity scanning strategy. In the SLM processing, the residual stress in different parts of the specimen varies with temperature gradient, and the residual stress at the edge of the specimen is obviously larger than that at the center. Under the chessboard scanning and preheating temperature 160°C, the residual stress in each direction of the specimens reaches the minimum. Under different forming processes, the morphology of the microstructure is obviously different. With the increase of preheating temperature, the molten pool in the side surface is obviously elongated and highly unevenly distributed. From the coupling relationship between the residual stress and microstructure, it can be found that the microstructure of top surface is affected by residual stresses σx and σy. But the side surface is mainly governed by residual stress σy; moreover, the greater the residual stress, the more obvious the grain tilt. In the XY and XZ surfaces, the scanning strategy has little influence on the tilt angle of the grain. But, the tilt angle and morphology of the microstructure are obviously affected by the preheating temperature. The results show that the residual stresses can effectively change the properties of the materials under the combined influence of scanning strategy and preheating temperature.

scholarly journals Effect of Process Parameters and High-Temperature Preheating on Residual Stress and Relative Density of Ti6Al4V Processed by Selective Laser Melting

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 930 ◽  
Author(s):  
Martin Malý ◽  
Christian Höller ◽  
Mateusz Skalon ◽  
Benjamin Meier ◽  
Daniel Koutný ◽  
...  
Keyword(s):  
Residual Stress ◽  
High Temperature ◽  
Residual Stresses ◽  
Relative Density ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Stress Reduction ◽  
Laser Melting ◽  
Preheating Temperature ◽  
Laser Velocity

The aim of this study is to observe the effect of process parameters on residual stresses and relative density of Ti6Al4V samples produced by Selective Laser Melting. The investigated parameters were hatch laser power, hatch laser velocity, border laser velocity, high-temperature preheating and time delay. Residual stresses were evaluated by the bridge curvature method and relative density by the optical method. The effect of the observed process parameters was estimated by the design of experiment and surface response methods. It was found that for an effective residual stress reduction, the high preheating temperature was the most significant parameter. High preheating temperature also increased the relative density but caused changes in the chemical composition of Ti6Al4V unmelted powder. Chemical analysis proved that after one build job with high preheating temperature, oxygen and hydrogen content exceeded the ASTM B348 limits for Grade 5 titanium.

Deformations and stresses prediction of cantilever structures fabricated by selective laser melting process

2021 ◽  
Vol 27 (3) ◽  
pp. 453-464
Author(s):  
Lan Li ◽  
Tan Pan ◽  
Xinchang Zhang ◽  
Yitao Chen ◽  
Wenyuan Cui ◽  
...  
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Selective Laser Melting ◽  
Thermal Distortion ◽  
Cantilever Beams ◽  
Support Structures ◽  
Laser Melting ◽  
Content Type ◽  
Two Samples ◽  
Validation Experiments

Purpose During the powder bed fusion process, thermal distortion is one big problem owing to the thermal stress caused by the high cooling rate and temperature gradient. For the purpose of avoiding distortion caused by internal residual stresses, support structures are used in most selective laser melting (SLM) process especially for cantilever beams because they can assist the heat dissipation. Support structures can also help to hold the work piece in its place and reduce volume of the printing materials. The mitigation of high thermal gradients during the manufacturing process helps to reduce thermal distortion and thus alleviate cracking, curling, delamination and shrinkage. Therefore, this paper aims to study the displacement and residual stress evolution of SLMed parts. Design/methodology/approach The objective of this study was to examine and compare the distortion and residual stress properties of two cantilever structures, using both numerical and experimental methods. The part-scale finite element analysis modeling technique was applied to numerically analyze the overhang distortions, using the layer-by-layer model for predicting a part scale model. The validation experiments of these two samples were built in a SLM platform. Then average displacement of the four tip corners and residual stress on top surface of cantilever beams were tested to validate the model. Findings The validation experiments results of average displacement of the four tip corners and residual stress on top surface of cantilever beams were tested to validate the model. It was found that they matched well with each other. From displacement and residual stress standpoint, by introducing two different support structure, two samples with the same cantilever beam can be successfully printed. In terms of reducing wasted support materials, print time and high surface quality, sample with less support will need less post-processing and waste energy. Originality/value Numerical modeling in this work can be a very useful tool to parametrically study the feasibility of support structures of SLM parts in terms of residual stresses and deformations. It has the capability for fast prediction in the SLMed parts.

scholarly journals Influence of Scanning Strategy Parameters on Residual Stress in the SLM Process According to the Bridge Curvature Method for AISI 316L Stainless Steel

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1659 ◽  
Author(s):  
Jiri Hajnys ◽  
Marek Pagáč ◽  
Jakub Měsíček ◽  
Jana Petru ◽  
Mariusz Król
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Process Parameters ◽  
316L Stainless Steel ◽  
Stress Generation ◽  
Aisi 316L ◽  
Laser Melting ◽  
Scanning Strategy ◽  
Aisi 316L Stainless Steel ◽  
Strategy Parameters

The present paper deals with the investigation and comparison of the influence of scanning strategy on residual stress in the selective laser melting (SLM) process. For the purpose of the experiment, bridge geometry samples were printed by a 3D metal printer, which exhibited tension after cutting from the substrate, slightly bending the samples toward the laser melting direction. Samples were produced with the variation of process parameters and with a change in scanning strategy which plays a major role in stress generation. It was evaluated using the Bridge Curvature Method (BCM) and optical microscopy. At the end, a recommendation was made.

scholarly journals The Effect of a Scanning Strategy on the Residual Stress of 316L Steel Parts Fabricated by Selective Laser Melting (SLM)

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1821 ◽  
Author(s):  
Di Wang ◽  
Shibiao Wu ◽  
Yongqiang Yang ◽  
Wenhao Dou ◽  
Shishi Deng ◽  
...  
Keyword(s):  
Residual Stress ◽  
Selective Laser Melting ◽  
Laser Scanning ◽  
Effective Means ◽  
Laser Melting ◽  
Scanning Strategy ◽  
Deformation Degree ◽  
316L Steel ◽  
Stress And Deformation ◽  
Scanning Strategies

The laser scanning strategy has an important influence on the surface quality, residual stress, and deformation of the molten metal (deformation behavior). A divisional scanning strategy is an effective means used to reduce the internal stress of the selective laser melting (SLM) metal part. In order to understand and optimize the divisional scanning strategy, three divisional scanning strategies and an S-shaped orthogonal scanning strategy are used to produce 316L steel parts in this study. The influence of scanning strategy on the produced parts is verified from the aspects of densification, residual stress distribution and deformation. Experiments show that the 316L steel alloy parts adopted spiral divisional scanning strategy can not only obtain the densification of 99.37%, but they also effectively improve the distribution of residual stress and control the deformation degree of the produced parts. Among them, the spiral divisional scanning sample has the smallest residual stress in plane direction, and its σx and σy stress are controlled within 204 MPa and 103 MPa. The above results show that the spiral divisional scanning is the most conducive strategy to obtain higher residual stress performance of SLM 316L steel parts.

Investigation of Sectoral Scanning in Selective Laser Melting

2010 ◽  
Author(s):  
Evren Yasa ◽  
Jan Deckers ◽  
Jean-Pierre Kruth ◽  
Marleen Rombouts ◽  
Jan Luyten
Keyword(s):  
Mechanical Properties ◽  
Residual Stresses ◽  
Laser Beam ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Random Order ◽  
Laser Source ◽  
Metal Powders ◽  
Laser Melting ◽  
Powder Bed

Selective laser melting (SLM), a powder metallurgical (PM) additive manufacturing (AM) technology, is able to produce fully functional parts directly from standard metal powders without using any intermediate binders or any additional post-processing steps. During the process, a laser beam selectively scans a powder bed according to the CAD data of the part to be produced and completely melts the powder particles together. Stacking and bonding two-dimensional powder layers in this way, allows production of fully dense parts with any geometrical complexity. The scanning of the powder bed by the laser beam can be achieved in several different ways, one of which is island or sectoral scanning. In this way, the area to be scanned is divided in small square areas (‘sectors’) which are scanned in a random order. This study is carried out to explore the influence of sectoral scanning on density, surface quality, mechanical properties and residual stresses formed during SLM. The experiments are carried out on a machine with an Nd:YAG laser source using AISI 316L stainless steel powder. As a result of this experimental study, it is concluded that sectoral scanning has some advantages such as lower residual stresses and better surface quality. However, the selection of parameters related to sectoral scanning is a critical task since it may cause aligned porosity at the edges between sectors or scanned tracks, which is very undesired in terms of mechanical properties.

A Method to Estimate Residual Stress in Metal Parts Made by Selective Laser Melting

2015 ◽  
Author(s):  
Xiaoqing Wang ◽  
Y. Kevin Chou
Keyword(s):  
Residual Stress ◽  
Additive Manufacturing ◽  
Residual Stresses ◽  
Selective Laser Melting ◽  
Inconel 718 ◽  
Plane Surface ◽  
Texture Evolution ◽  
Large Temperature ◽  
Indentation Hardness ◽  
Laser Melting

Accurate evaluation of residual stresses in structures is very important because they play a crucial role in the mechanical performance of the components. As residual stresses can be introduced into mechanical components during various thermal or mechanical processes such as heat treatment, forming, welding and additive manufacturing. As an additive manufacturing method, selective laser melting (SLM) has become a powerful tool for the direct manufacturing of three dimensional nano-composite components with complex configurations directly from powders using 3D CAD data as a digital information source and energy in the form of a high-power laser beam. Therefore, the application of the SLM technology is necessary to manufacture Inconel 718 superalloy, which has been widely employed in industrial applications due to its remarkable properties. Hence, it is critical to measure and reduce the residual stress in the Inconel 718 parts formed by SLM due to rapid cooling and reheating. In this study, the process-induced residual stress in Inconel 718 parts produced by selective laser melting (SLM) has been investigated using the model established by Carlsson et al., which is an instrumented indentation technique based on the experimental correlation between the indentation characteristic and the residual stress. The samples were sectioned from an Inconel 718 block along its build direction, and subsequently prepared with general metallographic methods for Vickers indentation and measurements by optical microscopy. The residual stress on the scanning surface (Z-plane) and side surface (X-plane) at different build heights have been evaluated in micro-scale with the contact area, indentation hardness and the equai-biaxial residual stress and strain fields. The results show that the residual stress is unevenly distributed in the SLMed parts with some areas have an maximum absolute value around 350 MPa, about 30 percent of the yield strength of Inconel 718. The average residual stresses in the Z-plane and X-plane samples are tensile and compressive, respectively. Besides, the residual stress does not change significantly along the building direction of the part. Moreover, the Vickers hardness of the parts built with the SLM process is comparable to the literature, and the X-plane surface has a higher hardness than the Z-plane surface. The microstructures and texture evolution of the SLM processed Inconel 718 alloy are also investigated. The X-plane shows the columnar structure due to the large temperature gradient while the Z-plane presents the equiaxed structures. The random texture is shown in the SLM processed specimens.

scholarly journals Investigation of Residual Stresses Induced during the Selective Laser Melting Process

2013 ◽  
Vol 554-557 ◽  
pp. 1828-1834 ◽  
Author(s):  
Laurent van Belle ◽  
Guillaume Vansteenkiste ◽  
Jean Claude Boyer
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Selective Laser Melting ◽  
Complex Geometry ◽  
Melting Process ◽  
Hole Drilling ◽  
Internal Stresses ◽  
Laser Melting ◽  
Selective Laser Melting Process ◽  
Engineering Materials

The selective laser melting process (SLM), belonging to the family of additive manufacturing processes, can create complex geometry parts from a CAD file. Previously, only prototypes were created by SLM, but now this process is used to manufacture quickly and directly functional parts. For example, in the PEP (Pôle Européen de la Plasturgie), this process is used to fabricate tooling parts or injection molds with cooling channels that can’t be obtained by conventional routes. During the process, the laser beam generates violent heating and cooling cycles in the material inducing important thermal gradients in the consolidated part. The cyclic thermal expansions and contractions exceeding the maximum elastic strain of the material induce heterogeneous plastic strains and generate internal stresses the level of which can reaches the yield stress of the material and cracks may appear during the process. This paper deals with the measurement and analysis of residual stresses during the selective laser melting of a simple part in maraging steel. The objective of this study is the analysis of experimental results to validate the numerical model previously presented in [1]. Some authors have investigated the residual stresses produced in SLM parts using different experimental measurement methods such as the incremental hole drilling method in [2], the layer removal method see in [3] and [4] or the non-destructive method, by neutron diffraction in [5]. A new method is proposed to evaluate the residual stresses induced during the SLM process, a rosette is fixed on the bottom face of the support. The residual stresses in the created part are calculated from strain and temperature variations when the fused layer is consolidating during the cooling between two layers. Process parameters like the powder thickness or the time cooling between successive layers are studied in this paper. [1] L. Van Belle, G. Vansteenkiste, J.C. Boyer, Comparisons of numerical modeling of the selective laser melting, Key Engineering Materials Vols. 504-506 (2012) pp 1067-1072 [2] C. Casavola, S.L. Campanelli, C. Pappalettere, Experimental analysis of residual stresses in the selective laser melting process, Proceedings of the XIth International Congress and Exposition, June 2-5, 2008 Orlando, Florida USA [3] M. Shiomi, K. Osakada, K. Nakamura, T. Yamashita, F. Abe, Residual stress within metallic model made by selective laser melting process, CIRP Annals - Manufacturing Technology, Vol. 53, No. 1. (2004), pp. 195-198 [4] T. Furumoto, T. Ueda, M.S. Abdul Aziz, A. Hosokawa and R. Tanaka, Study on reduction of residual stress induced during rapid tooling process, influence of heating conditions on residual stress, Key Engineering Materials Vols. 447-448 (2010) pp 785-789 [5] M. Zaeh, G. Branner, Investigation on residual stresses and deformation in selective laser melting, Production Engineering, Volume 4, Number 1 (2010)

Sign in / Sign up

Export Citation Format

Share Document