scholarly journals Investigation on Composition, Mechanical Properties, and Corrosion Resistance of Mg-0.5Ca-X(Sr, Zr, Sn) Biological Alloy

Scanning ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-10
Author(s):  
Yichang Su ◽  
Jixing Lin ◽  
Yingchao Su ◽  
Wei Zai ◽  
Guangyu Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Optical Microscope ◽  
Pure Magnesium ◽  
Second Phase ◽  
Energy Dispersion Spectroscopy ◽  
X Ray ◽  
Corrosion Behaviors ◽  
Mechanical Properties And Corrosion ◽  
Fluorescence Spectrometer ◽  
Hank’S Solution

Four nontoxic biological alloys, Mg-0.5Ca-1Sr-4Zr (Alloy 1), Mg-0.5Ca-1Sr-1.5Zr (Alloy 2), Mg-0.5Ca-3Sr-1.5Zr (Alloy 3), and Mg-0.5Ca-1Sr-0.5Sn (Alloy 4), were prepared by vacuum smelting, gravity casting, and hot rolling. The composition and microstructure of the alloys were investigated by optical microscope, X-ray fluorescence spectrometer (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM), and energy dispersion spectroscopy (EDS). The mechanical properties and corrosion behaviors of the alloys in Hank’s solution were studied. Results showed that a large amount of fine and uniformly distributed second-phase particles (Zr, Mg17Sr2, and CaMgSn) was observed in four alloys obtained after rolling and alloying. The segregation of Zr in alloys was observed in EDS image, and chemical analysis showed that there was macrosegregation of the elements in the alloys. Furthermore, Mg17Sr2 phases in the Mg-0.5Ca-1Sr-0.5Sn alloy homogenized the distribution of CaMgZn phases. The comprehensive mechanical properties of four newly designed rolled alloys were much higher than those of pure Mg, and the compressive strength of the alloys was more than twice as high as that of pure magnesium. The Mg-0.5Ca-1Sr-0.5Sn alloy released the least hydrogen in Hank’s solution, which was lower than that of pure magnesium. Electrochemical test results in Hank’s solution further showed that the Mg-0.5Ca-1Sr-0.5Sn alloy had delayed corrosion and lowest Icorr which was 25% of that of pure magnesium. Biological experiments results showed that the Mg-0.5Ca-1Sr-0.5Sn alloy had better biocompatibility and optimal potential for bone substitute material.

scholarly journals Effect of the Zn/Mg Ratio on Microstructures, Mechanical Properties and Corrosion Performances of Al-Zn-Mg Alloys

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3299
Author(s):  
Keda Jiang ◽  
Yanquan Lan ◽  
Qinglin Pan ◽  
Yunlai Deng
Keyword(s):  
Mechanical Properties ◽  
Electron Microscope ◽  
Grain Boundary ◽  
Stress Corrosion ◽  
Intergranular Corrosion ◽  
Optical Microscope ◽  
Mg Alloys ◽  
Sensitivity Index ◽  
Second Phase ◽  
Mechanical Properties And Corrosion

The effect of the Zn/Mg ratio on microstructures, mechanical properties and corrosion performances of Al-Zn-Mg alloys was studied. Microstructures were characterized using the optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM). Tensile tests, intergranular corrosion (IGC) and stress corrosion cracking (SCC) tests were conducted to study the properties. Microstructures results indicated that with the decrease of the Zn/Mg ratio, the recrystallization proportion and the fraction of second phase decreased, while the size of η’ (MgZn2) phases in grain interior also significantly decreased. The number density of η’ phases in grain interior increased and grain boundary precipitates developed discontinuous distribution with the decrease of the Zn/Mg ratio. These microstructures contributed to the significant improvement of the strength and corrosion resistance. The tensile strength and yield strength increased by 34.1% and 47.4%, respectively, with the Zn/Mg ratio decreased from 11.4 to 6.1. Calculating results indicated that the enhancement of strength mainly contributed from the solid-solution strengthening, grain-boundary strengthening and precipitation strengthening. The intergranular corrosion degree was greatly relieved and the stress corrosion sensitivity index decreased from 0.031 to 0.007 with the Zn/Mg ratio decreased from 11.4 to 6.1.

Microstructure, Mechanical and Degradation Properties of Extruded Pure Mg for Biomedical Application

2012 ◽  
Vol 557-559 ◽  
pp. 1231-1234 ◽  
Author(s):  
Zhi Li ◽  
Jiong Zhao
Keyword(s):  
Mechanical Properties ◽  
Biomedical Application ◽  
Optical Microscope ◽  
Biodegradable Implant ◽  
Bodily Fluids ◽  
Microstructure Observation ◽  
Mechanical Properties And Corrosion ◽  
Cast Magnesium ◽  
Degradation Properties ◽  
Hank’S Solution

Magnesium is potential biodegradable implant materials due to its attractive biological property, degradability and possesses mechanical properties similar to bone. But cast magnesium has an unsatisfactory mechanical property. Microstructure, mechanical properties, and degradation properties of the extruded pure Mg have been investigated by use of optical microscope, tensile testing, and Hank's solution that simulates bodily fluids. Microstructure observation has shown that the extrusion significantly refined the grain size of the cast magnesium, which mainly contributes to the high tensile strength and good elongation. The degradation rate is shown to be significantly reduced by grain refinement produced by extrusion. The results of the present study showed that pure magnesium by extrusion treatment is a simple and promising way of enhancing the mechanical properties and corrosion resistance of pure Mg in Hanks' solution.

Microstructure and mechanical properties of 15-5 PH stainless steel under different aging temperature

2021 ◽  
Vol 118 (6) ◽  
pp. 601
Author(s):  
Chunhui Jin ◽  
Honglin Zhou ◽  
Yuan Lai ◽  
Bei Li ◽  
Kewei Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Aging Temperature ◽  
Electron Backscatter Diffraction ◽  
Lath Martensite ◽  
Optical Microscope ◽  
Second Phase ◽  
Strengthening Mechanisms ◽  
Microstructure And Mechanical Properties ◽  
Transmission Electron

The influence of aging temperature on microstructure and mechanical properties of Cr15Ni5 precipitation hardening stainless steel (15-5 PH stainless steel) were investigated at aging temperature range of 440–610 °C. The tensile properties at ambient temperature of the 15-5 PH stainless steel processed by different aging temperatures were tested, and the microstructural features were further analyzed utilizing optical microscope (OM), transmission electron microscope (TEM), electron backscatter diffraction (EBSD) as well as X-ray diffraction (XRD), respectively. Results indicated the strength of the 15-5 PH stainless steel was firstly decreased with increment of aging temperature from 440 to 540 °C, and then increased with the increment of aging temperature from 540 to 610 °C. The strength and ductility were well matched at aging temperature 470 °C, and the yield strength, tensile strength as well as elongation were determined to be 1170 MPa, 1240 MPa and 24%, respectively. The microstructures concerning to different aging temperatures were overall confirmed to be lath martensite. The strengthening mechanisms induced by dislocation density and the second phase precipitation of Cu-enriched metallic compound under different aging temperatures were determined to be the predominant strengthening mechanisms controlling the variation trend of mechanical properties corresponding to different aging temperatures with respect to 15-5 PH stainless steel.

scholarly journals Effect of deformation and annealing temperature on the mechanical properties and microstructure of Al-4.5Zn-1.5Mg-0.9Cr (wt. %) alloy fabricated by squeeze casting

2018 ◽  
Vol 153 ◽  
pp. 01001
Author(s):  
Maya Putri Agustianingrum ◽  
Nuzulian Akbar Arandana ◽  
Risly Wijanarko ◽  
Bondan Tiara Sofyan
Keyword(s):  
Mechanical Properties ◽  
Squeeze Casting ◽  
Deformation Behaviour ◽  
Optical Microscope ◽  
Dislocation Motion ◽  
Hot Tearing ◽  
Mg Alloys ◽  
Recrystallization Temperature ◽  
Forming Process ◽  
Mechanical Properties And Corrosion

In order to produce structural products, Al-Zn-Mg alloys undergo various forming processes. Problems that are usually found in the forming process include peripheral coarse grain (PCG) and hot tearing which decrease mechanical properties and corrosion resistance of the alloys. Addition of microalloying element such as chromium (Cr) is an alternative to overcome these problems. The presence of Cr in Al-Zn-Mg alloys supresses the grain growth by preventing excess recrystallization. In this research 0.9 wt. % Cr was added to Al-4.5Zn-1.5Mg alloy and the deformation behaviour as well as subsequent recrystallization was observed. The alloy was fabricated by squeeze casting followed by homogenization at 400 °C for 4 h. The samples were cold rolled for 5, 10, and 20 %. The 20 % deformed samples were then annealed at 300, 400, and 500 °C for 2 h. Material characterization consisted of microstructure analysis using optical microscope and Scanning Electron Microscope (SEM) – Energy Dispersive Spectroscopy (EDS), hardness testing using Micro Vicker methods. The results showed that the deformed grain ratio was 1.6, 2.84, and 2.99 in the 5, 10, and 20 % deformed samples, respectively. The elongated dendrites were effective to increase the hardness of the alloy. Recrystallization was not detected during annealing at 300 and 400 °C, but was observed at 500 °C. Whereas, for the samples without Cr addition, recrystallization occurred at 400 °C. It means that the addition of Cr increased the recrystallization temperature of the alloy. It occured because (Al, Zn)7Cr dispersoids with size less than 1 μm impeded the dislocation motion during annealing, so that recrystallization was retarded. On the other hand (Al, Zn)7Cr dispersoids with size more than 1 μm promoted the formation of new grains around them by Particle Stimulated Nucleation (PSN) mechanism. In this case, the fine (Al, Zn)7Cr dominated so that recrystallization was slower.

scholarly journals Improved Mechanical Properties and Corrosion Resistance of Mg-Based Bulk Metallic Glass Composite by Coating with Zr-Based Metallic Glass Thin Film

Coatings ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1212
Author(s):  
Pei-Hua Tsai ◽  
Chung-I Lee ◽  
Sin-Mao Song ◽  
Yu-Chin Liao ◽  
Tsung-Hsiung Li ◽  
...  
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Metallic Glass ◽  
Bulk Metallic Glass ◽  
Substrate Surface ◽  
Bending Test ◽  
Corrosion Behaviors ◽  
Lightweight Structure ◽  
Mechanical Properties And Corrosion

Mg-based bulk metallic glass (BMG) and its composite (BMGC) can be excellent candidates as lightweight structure materials, but lack of anti-corrosion ability may restrict their application. In order to enhance the natural weak point of Mg-based BMGC, a 200-nm thick Zr-based metallic glass thin film (MGTF) ((Zr53Cu30Ni9Al8)99.5Si0.5) was applied and its mechanical properties as well as its corrosion resistance were appraised. The results of a 3-point bending test revealed that the flexural strength of the Mg-based BMGC with 200-nm thick Zr-based MGTF coating can be greatly enhanced from 180 to 254 MPa. We propose that the Zr-based MGTF coating can help to cover any small defects of a substrate surface, provide a protecting layer to prevent stress concentration, and cease crack initiation from the specimen surface during bending tests. Moreover, the results of anti-corrosion behavior analysis revealed a similar trend between the Mg-based BMG, Mg-based BMGC, and Mg-based BMGC with Zr-based MGTF coating in 0.9 wt.% sodium chloride solution. The readings show a positive effect with the Zr-based MGTF coating. Therefore, the 200-nm thick Zr-based MGTF coating is a promising solution to provide protection for both mechanical and anti-corrosion behaviors of Mg-based BMGC and reinforce its capability as structure material in island environments.

Microstructure characterization and evaluation of mechanical properties of stir rheocast AA2024/TiB2 composite

2019 ◽  
Vol 54 (7) ◽  
pp. 981-997
Author(s):  
Semegn Cheneke ◽  
D Benny Karunakar
Keyword(s):  
Mechanical Properties ◽  
Dendritic Structure ◽  
Optical Microscope ◽  
X Ray Diffraction ◽  
Globular Structure ◽  
Cast Sample ◽  
X Ray ◽  
Weight Percentage ◽  
The Matrix ◽  
Fractured Surface

In this research, microstructure and mechanical properties of stir rheocast AA2024/TiB2 metal matrix composite have been investigated. The working temperature was 640℃, which was the selected semisolid temperature that corresponds to 40% of the solid fraction. Two weight percentage, 4 wt%, and 6 wt% of the TiB2 reinforcements were added to the matrix. The field emission scanning electron microscope micrographs of the developed composites showed a uniform distribution of the particles in the case of the 2 wt% and 4 wt% of the reinforcements. However, the particles agglomerated as the weight percentages of the reinforcement increases to 6%. The optical microscope of the liquid cast sample showed the dendritic structure, whereas the rheocast samples showed a globular structure. The X-ray diffraction analysis confirmed the distribution of the reinforcements in the matrix and the formation of some intermetallic compounds. Mechanical properties significantly improved by the addition of the reinforcements in the matrix. An increase in tensile strength of 13.3%, 40%, 28%, and 5% was achieved for the unreinforced rheocast sample, 2 wt%, 4 wt%, and 6 wt% reinforced rheocast samples respectively, compared to the liquid cast sample. An increase in 20% of hardness was attained for the composite with 2 wt% TiB2 compared to the liquid cast sample. According to the fractography analysis, small dimples were observed on the fractured surface of the unreinforced rheocast sample, whereas small and large voids were dominant on the fractured surface of the 2 wt% composite, which shows the ductile fracture mode.

Study on Weldablity of Dissimilar Steel between 16MnR and S31803

2011 ◽  
Vol 391-392 ◽  
pp. 768-772 ◽  
Author(s):  
Li Yang ◽  
Zhan Zhe Zhang
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Impact Toughness ◽  
Weld Metal ◽  
Welded Joint ◽  
Optical Microscope ◽  
Dissimilar Steel ◽  
Austenite Content ◽  
Mechanical Properties And Corrosion ◽  
The Impact

The weldablity of dissimilar steel between 16MnR and S31803 was analyzed and researched. By means of optical microscope (OM), the microstructure of the weld joint was investigated, which is welded by tungsten inert gas arc backing welding (GTAW) and manual arc filling welding (SMAW). The mechanical properties and corrosion resistance of the welded joint was also tested and studied. Results indicate that austenite and acicular ferrite distribute uniformly in the weld metal, which strengths the toughness and ductility of the joint. The austenite content in weld is higher than that in over-heated zone of S31803.The SMAW joint structure is coarsening than that of GTAW and has more austenite content. It is also observed that there are a decarburization layer and a carbon-enriched zone nearby the fusion line. And very small amounts of the third phase of harmful metal phase are found in the fusion zone of S31803 side. The welded joint shows the excellent mechanical properties and corrosion resistance. The impact toughness of the weld metal is higher than in HAZ of 16MnR side, and the impact toughness at GTAW side and in HAZ is superior to the SMAW side.

Sign in / Sign up

Export Citation Format

Share Document