scholarly journals Dynamic Properties of Clean Sand Modified with Granulated Rubber

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Dervis Volkan Okur ◽  
Seyfettin Umut Umu
Keyword(s):  
Shear Modulus ◽  
Dynamic Characteristics ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Relative Size ◽  
Cyclic Behavior ◽  
Damping Capacity ◽  
Resonant Column ◽  
Strain Dependent

Waste automobile tires are used as additives or replacements instead of traditional materials in civil engineering works. In geotechnical engineering, tires are shredded to certain sizes and mixed with soil, especially used as backfill material behind retaining walls or fill material for roadway embankments. Compared to soil, rubber has high damping capacity and low shear modulus. Therefore, it requires the determination of the dynamic characteristics of rubber/soil mixtures. In this paper, the cyclic behavior of recycled tire rubber and clean sand was studied, considering the effects of the amount and particle size of the rubber and confining stresses. A total of 40 stress-controlled tests were performed on an integrated resonant column and dynamic torsional shear system. The effects of the relative size and proportion of the rubber on the dynamic characteristics of the mixtures are discussed. The dynamic properties, such as the maximum shear modulus, strain-dependent shear modulus, and damping ratio, are examined. For practical purposes, simple empirical relationships were formulated to estimate the maximum shear modulus and the damping ratio. The change in the shear modulus and damping ratio with respect to shear strain with 5% of rubber within the mixture was found to be close to the behavior of clean sand.

scholarly journals Evaluation of Dynamic Properties of Sodium-Alginate-Reinforced Soil Using A Resonant-Column Test

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2743
Author(s):  
Seongnoh Ahn ◽  
Jae-Eun Ryou ◽  
Kwangkuk Ahn ◽  
Changho Lee ◽  
Jun-Dae Lee ◽  
...  
Keyword(s):  
Shear Modulus ◽  
Sodium Alginate ◽  
Shear Failure ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Reinforced Soil ◽  
Resonant Column ◽  
Column Test ◽  
Alginate Solution ◽  
Resonant Column Test

Ground reinforcement is a method used to reduce the damage caused by earthquakes. Usually, cement-based reinforcement methods are used because they are inexpensive and show excellent performance. Recently, however, reinforcement methods using eco-friendly materials have been proposed due to environmental issues. In this study, the cement reinforcement method and the biopolymer reinforcement method using sodium alginate were compared. The dynamic properties of the reinforced ground, including shear modulus and damping ratio, were measured through a resonant-column test. Also, the viscosity of sodium alginate solution, which is a non-Newtonian fluid, was also explored and found to increase with concentration. The maximum shear modulus and minimum damping ratio increased, and the linear range of the shear modulus curve decreased, when cement and sodium alginate solution were mixed. Addition of biopolymer showed similar reinforcing effect in a lesser amount of additive compared to the cement-reinforced ground, but the effect decreased above a certain viscosity because the biopolymer solution was not homogeneously distributed. This was examined through a shear-failure-mode test.

scholarly journals Theoretical Framework for Characterizing Strain-Dependent Dynamic Soil Properties

2019 ◽  
Vol 9 (9) ◽  
pp. 1897
Author(s):  
Song-Hun Chong
Keyword(s):  
Shear Modulus ◽  
Constitutive Model ◽  
Soil Properties ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Theoretical Framework ◽  
Backbone Curve ◽  
Dominant Soil ◽  
Hysteresis Nonlinearity ◽  
Strain Dependent

This paper proposes a theoretical framework for the characterization of the strain-dependent dynamic properties of soils. The analysis begins with an analytical constitutive model for soils under steady-state cyclic loading. The model describes the dominant soil characteristics, i.e., the hysteresis and nonlinearity with an intrinsic material property α, which physically represents the degree of the hysteresis nonlinearity in a medium. Explicit formulas for the backbone curve, tangent shear modulus, secant shear modulus, and damping ratio as a function of shear strain are derived directly from the constitutive model. A procedure is then developed to determine the parameter α in which the derived damping ratio equation is fitted to damping ratio data measured from the resonant column test (RCT). Clay and sand under three different levels of confinement stress are considered in the numerical evaluation. The capability of the proposed theoretical framework in predicting strain-dependent soil properties and responses is demonstrated.

scholarly journals Resonant Column Test on the Frozen Silt Soil Modulus and Damping at Different Temperatures

2017 ◽  
Author(s):  
Xiaobo Yu ◽  
Rui Sun ◽  
Xiaoming Yuan ◽  
Zhuoshi Chen ◽  
Jiuqi Zhang
Keyword(s):  
Shear Modulus ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Negative Temperature ◽  
Frozen Soil ◽  
Resonant Column ◽  
Engineering Construction ◽  
Resonant Column Test ◽  
Triaxial Apparatus ◽  
Different Temperatures

The shear modulus and damping ratio of frozen soil are thebasic parameters of its dynamic properties and are often testedwith the dynamic triaxial apparatus. However, the resonantcolumn apparatus is more suitable for the testing at the microstrainlevel. A resonant column apparatus was here used toidentify the varying modes with negative temperature of theinitial shear modulus, modulus ratio, and damping ratio of frozensilt. Correction factor curves indicate that the temperaturehas a great effect on the shear modulus and damping ratio offrozen silt. The curves also show that, within the sensitive stage,the temperature significantly affects the modulus and damping.Within the insensitive stage, the modulus and dampingwere insensitive to the temperature. The experimental resultsand analysis given here provide support for improving seismicdesign codes and offer reasonable parameters for seismicresponse analysis in engineering construction in cold regions.

scholarly journals Dynamic Behavior of Soft Subgrade Soils Treated with Boron Waste

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Volkan Okur ◽  
Kubra Akinci
Keyword(s):  
Shear Modulus ◽  
Dynamic Characteristics ◽  
Waste Treatment ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Treatment Success ◽  
Kaolinite Clay ◽  
Continuous Increase ◽  
Subgrade Soils ◽  
Montmorillonite Clays

A series of laboratory tests using resonant column and dynamic torsional shear tests were conducted on kaolinite and montmorillonite clays treated with boron waste. The effect of the boron waste on the dynamic characteristics of two clays was studied considering the effects of the plasticity index. Pulverized boron waste was mixed with the clay soils in different proportions. It has been seen that treatment with boron waste improved the dynamic properties of the two clays. However, increasing the amount of boron waste does not affect the dynamic characteristics of the samples in the same proportions. Increasing the amount of boron waste in the mixture increased the initial shear modulus of the montmorillonite clay up to 300% compared to untreated samples, whereas the reaction of the kaolinite clay with boron waste treatment was moderate. Degradation curves of treated and untreated soils in regard to shear strain are presented. In general treatment, success is dependent on the amount of boron waste and the clay type. The continuous increase with the amount of boron waste in the shear modulus and damping ratio is apparent on both clays.

The Dynamic Characteristics of a Couple System by Pedestrian Bridge and Walking Persons

2011 ◽  
Vol 71-78 ◽  
pp. 1499-1506 ◽  
Author(s):  
Dong Wang ◽  
Shi Qiao Gao ◽  
Michael Kasperski ◽  
Hai Peng Liu ◽  
Lei Jin
Keyword(s):  
Natural Frequency ◽  
Dynamic Characteristics ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Couple System ◽  
Damping Capacity ◽  
Single Beam ◽  
Simplified Approach ◽  
Beam Experiment ◽  
External Loads

The human body forms a complex dynamic system with more than one natural frequency and provides considerable damping capacities. In a simplified approach active persons can be modeled as external loads. While this approach may be sufficient for an activity like jumping, it has been shown already that for a bobbing person some interaction effects may occur. The question arises if also pedestrians are able to influence the dynamic characteristics of the structure they are actually crossing. Observations during a mass event with several thousand persons crossing a 66 m long bridge indicate that the damping capacity of the coupled structure may have increased. In this paper a single beam experiment was operated. The basic idea is to use a known background excitation induced by a shaker. It can be seen that both natural frequency and damping ratio have been changed comparing with empty structure. The change with passive person is stronger that an active person. Meanwhile, the linear sweep method which was used in measurement provides a good result for the analysis of dynamic properties of a structure.

scholarly journals Influence of fines content and initial shear stress on dynamic properties of hydraulic reclaimed soil

2002 ◽  
Vol 39 (1) ◽  
pp. 242-253 ◽  
Author(s):  
L -K Chien ◽  
Y -N Oh
Keyword(s):  
Shear Stress ◽  
Shear Modulus ◽  
Land Reclamation ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Prediction Method ◽  
Test Material ◽  
Resonant Column ◽  
Fines Content ◽  
Reclaimed Soil

The hydraulic placement of sand fill is one of the most important methods of land reclamation. During the reclamation process, losses of fines in sand are induced by the transportation of soil which affects the dynamic properties of the soil materials. In this study, the reclaimed soil in the Yunlin area of Taiwan is adopted as the test material. Different fines contents, different relative densities, and initial stress ratio were taken as test conditions. Resonant column tests were performed to evaluate the shear modulus and damping ratio of the reclaimed soil under initial shear stress. The results show that the maximum shear modulus decreases as the fines content increases. The influences of initial shear stress are discussed. A prediction method for maximum shear modulus under different fines content and initial shear stress is proposed based on empirical equations obtained. The results can be helpful for land reclamation design and assessment.Key words: reclaimed soil, fines content, initial shear stress, dynamic properties.

A Study on Dynamic Properties of Cement-Stabilized Soils

2011 ◽  
Vol 243-249 ◽  
pp. 2050-2054 ◽  
Author(s):  
Pei Hsun Tsai ◽  
Sheng Huoo Ni
Keyword(s):  
Shear Modulus ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Test Results ◽  
Resonant Column Test ◽  
Stabilized Soil ◽  
Shearing Strain ◽  
Relationship Of ◽  
The Relationship

In this paper the dynamic property (shear modulus and damping ratio) of cement-stabilized soil is studied with using the resonant column test. The amount of cement admixed, the magnitude of confining pressure, and shearing strain amplitude are the parameters considered. Test results show that the maximum shear modulus of cement-stabilized soil increases with increasing confining pressure, the minimum damping ratio decreases with increasing confining pressure. The shear modulus of cement-stabilized soil decreases with increasing shearing strain while the damping ratio increases with increasing shearing strain. In the paper the relationship of shear modulus versus shearing strain is fitted into the Ramberg-Osgood equations using regression analysis.

scholarly journals Characterization of the Dynamic Properties of Clay–Gravel Mixtures at Low Strain Level

2020 ◽  
Vol 12 (4) ◽  
pp. 1616 ◽  
Author(s):  
Xianwen Huang ◽  
Aizhao Zhou ◽  
Wei Wang ◽  
Pengming Jiang
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Mechanical Performance ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Strain Level ◽  
Dynamic Shear Modulus ◽  
Dynamic Shear ◽  
Gravel Content

In order to support the dynamic design of subgrade filling engineering, an experiment on the dynamic shear modulus (G) and damping ratio (D) of clay–gravel mixtures (CGMs) was carried out. Forty-two groups of resonant column tests were conducted to explore the effects of gravel content (0%, 10%, 20%, 30%, 40%, 50%, and 60%, which was the mass ratio of gravel to clay), gravel shape (round and angular gravels), and confining pressure (100, 200, and 300 kPa) on the dynamic shear modulus, and damping ratio of CGMs under the same compacting power. The test results showed that, with the increase of gravel content, the maximum dynamic shear modulus of CGMs increases, the referent shear strain increases linearly, and the minimum and maximum damping ratios decrease gradually. In CGMs with round gravels, the maximum dynamic shear modulus and the maximum damping ratio are greater, and the referent shear strain and the minimum damping ratio are smaller, compared to those with angular gravels. With the increase of confining pressure, the maximum dynamic shear modulus and the referent shear strain increase nonlinearly, while the minimum and maximum damping ratios decrease nonlinearly. The predicting equation for the dynamic shear modulus and the damping ratio of CGMs when considering confining pressure, gravel content, and shape was established. The results of this research may put forward a solid foundation for engineering design considering low-strain-level mechanical performance.

Shear modulus reduction and damping ratio curves for earth core materials of dams

2019 ◽  
Vol 56 (1) ◽  
pp. 14-22 ◽  
Author(s):  
DongSoon Park ◽  
Tadahiro Kishida
Keyword(s):  
Shear Modulus ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Empirical Relationship ◽  
Embankment Dams ◽  
In Situ Data ◽  
Earth Core ◽  
Dynamic Analyses ◽  
Modulus Reduction ◽  
Core Materials

It is essential to obtain shear modulus reduction and damping ratio curves to perform dynamic analyses of earth-cored embankment dams. Many studies have been performed for dynamic properties of clayey soils, but they have been limited for earth core materials of dams. This study conducted resonant column tests to obtain shear modulus reduction (G/Gmax) and damping ratio (D) curves for 31 specimens (17 undisturbed and 14 remolded specimens) from 13 earth-cored embankment dams. Empirical G/Gmax and D curves are proposed for dynamic properties of clayey earth core materials. Fitting curves are provided by using the functional forms of the Ramberg–Osgood and Darendeli models. The observation shows that the undisturbed earth cores yield relatively higher G/Gmax and lower D curves than the remolded cores. G/Gmax curves of compacted earth cores are relatively higher than those of Vucetic and Dobry curves for a similar level of plasticity index. Uncertainty and bias are calculated by performing residual analysis, which shows that there is no clear bias in predicting G/Gmax and the uncertainties between undisturbed earth core materials and natural deposits are at a similar level. A proposed empirical relationship of G/Gmax and D curves for earth core materials can be utilized for dynamic analyses of embankment dams for cases where there is insufficient in situ data.

Structure characteristics and mechanical properties of kaolinite soils. II. Effects of structure on mechanical properties

2006 ◽  
Vol 43 (6) ◽  
pp. 601-617 ◽  
Author(s):  
Y -H Wang ◽  
W -K Siu
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Shear Modulus ◽  
Critical State ◽  
Soil Structure ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Undrained Shear Strength ◽  
Interparticle Forces ◽  
Undrained Shear

This paper reports the effects of structure on the mechanical responses of kaolinite with known and controlled fabric associations. The dynamic properties and strength were assessed by resonant column tests and undrained triaxial compression tests, respectively. The experimental results demonstrate that interparticle forces and associated fabric arrangements influence the volumetric change under isotropic compression. Soils with different structures have individual consolidation lines, and the merging trend is not readily seen under an isotropic confinement up to 250 kPa. The dynamic properties of kaolinite were found to be intimately related to the soil structure. Stronger interparticle forces or higher degrees of flocculated structure lead to a greater small-strain shear modulus, Gmax, and a lower associated damping ratio, Dmin. The soil structure has no apparent influence on the critical-state friction angle (ϕ′c = 27.5°), which suggests that the critical stress ratio does not depend on interparticle forces. The undrained shear strength of kaolinite is controlled by its initial packing density rather than by any interparticle attractive forces, and yet the influence of the structure on the effective stress path is obvious.Key words: interparticle forces, shear modulus, damping ratio, stress–strain behavior, undrained shear strength, critical state.

Sign in / Sign up

Export Citation Format

Share Document