scholarly journals Influence of fines content and initial shear stress on dynamic properties of hydraulic reclaimed soil

2002 ◽  
Vol 39 (1) ◽  
pp. 242-253 ◽  
Author(s):  
L -K Chien ◽  
Y -N Oh
Keyword(s):  
Shear Stress ◽  
Shear Modulus ◽  
Land Reclamation ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Prediction Method ◽  
Test Material ◽  
Resonant Column ◽  
Fines Content ◽  
Reclaimed Soil

The hydraulic placement of sand fill is one of the most important methods of land reclamation. During the reclamation process, losses of fines in sand are induced by the transportation of soil which affects the dynamic properties of the soil materials. In this study, the reclaimed soil in the Yunlin area of Taiwan is adopted as the test material. Different fines contents, different relative densities, and initial stress ratio were taken as test conditions. Resonant column tests were performed to evaluate the shear modulus and damping ratio of the reclaimed soil under initial shear stress. The results show that the maximum shear modulus decreases as the fines content increases. The influences of initial shear stress are discussed. A prediction method for maximum shear modulus under different fines content and initial shear stress is proposed based on empirical equations obtained. The results can be helpful for land reclamation design and assessment.Key words: reclaimed soil, fines content, initial shear stress, dynamic properties.

scholarly journals Evaluation of Dynamic Properties of Sodium-Alginate-Reinforced Soil Using A Resonant-Column Test

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2743
Author(s):  
Seongnoh Ahn ◽  
Jae-Eun Ryou ◽  
Kwangkuk Ahn ◽  
Changho Lee ◽  
Jun-Dae Lee ◽  
...  
Keyword(s):  
Shear Modulus ◽  
Sodium Alginate ◽  
Shear Failure ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Reinforced Soil ◽  
Resonant Column ◽  
Column Test ◽  
Alginate Solution ◽  
Resonant Column Test

Ground reinforcement is a method used to reduce the damage caused by earthquakes. Usually, cement-based reinforcement methods are used because they are inexpensive and show excellent performance. Recently, however, reinforcement methods using eco-friendly materials have been proposed due to environmental issues. In this study, the cement reinforcement method and the biopolymer reinforcement method using sodium alginate were compared. The dynamic properties of the reinforced ground, including shear modulus and damping ratio, were measured through a resonant-column test. Also, the viscosity of sodium alginate solution, which is a non-Newtonian fluid, was also explored and found to increase with concentration. The maximum shear modulus and minimum damping ratio increased, and the linear range of the shear modulus curve decreased, when cement and sodium alginate solution were mixed. Addition of biopolymer showed similar reinforcing effect in a lesser amount of additive compared to the cement-reinforced ground, but the effect decreased above a certain viscosity because the biopolymer solution was not homogeneously distributed. This was examined through a shear-failure-mode test.

scholarly journals Dynamic Properties of Clean Sand Modified with Granulated Rubber

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Dervis Volkan Okur ◽  
Seyfettin Umut Umu
Keyword(s):  
Shear Modulus ◽  
Dynamic Characteristics ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Relative Size ◽  
Cyclic Behavior ◽  
Damping Capacity ◽  
Resonant Column ◽  
Strain Dependent

Waste automobile tires are used as additives or replacements instead of traditional materials in civil engineering works. In geotechnical engineering, tires are shredded to certain sizes and mixed with soil, especially used as backfill material behind retaining walls or fill material for roadway embankments. Compared to soil, rubber has high damping capacity and low shear modulus. Therefore, it requires the determination of the dynamic characteristics of rubber/soil mixtures. In this paper, the cyclic behavior of recycled tire rubber and clean sand was studied, considering the effects of the amount and particle size of the rubber and confining stresses. A total of 40 stress-controlled tests were performed on an integrated resonant column and dynamic torsional shear system. The effects of the relative size and proportion of the rubber on the dynamic characteristics of the mixtures are discussed. The dynamic properties, such as the maximum shear modulus, strain-dependent shear modulus, and damping ratio, are examined. For practical purposes, simple empirical relationships were formulated to estimate the maximum shear modulus and the damping ratio. The change in the shear modulus and damping ratio with respect to shear strain with 5% of rubber within the mixture was found to be close to the behavior of clean sand.

scholarly journals Resonant Column Test on the Frozen Silt Soil Modulus and Damping at Different Temperatures

2017 ◽  
Author(s):  
Xiaobo Yu ◽  
Rui Sun ◽  
Xiaoming Yuan ◽  
Zhuoshi Chen ◽  
Jiuqi Zhang
Keyword(s):  
Shear Modulus ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Negative Temperature ◽  
Frozen Soil ◽  
Resonant Column ◽  
Engineering Construction ◽  
Resonant Column Test ◽  
Triaxial Apparatus ◽  
Different Temperatures

The shear modulus and damping ratio of frozen soil are thebasic parameters of its dynamic properties and are often testedwith the dynamic triaxial apparatus. However, the resonantcolumn apparatus is more suitable for the testing at the microstrainlevel. A resonant column apparatus was here used toidentify the varying modes with negative temperature of theinitial shear modulus, modulus ratio, and damping ratio of frozensilt. Correction factor curves indicate that the temperaturehas a great effect on the shear modulus and damping ratio offrozen silt. The curves also show that, within the sensitive stage,the temperature significantly affects the modulus and damping.Within the insensitive stage, the modulus and dampingwere insensitive to the temperature. The experimental resultsand analysis given here provide support for improving seismicdesign codes and offer reasonable parameters for seismicresponse analysis in engineering construction in cold regions.

A Study on the Effect of Initial Shear Stress on Dynamic Properties of Saturated Clay

2013 ◽  
Vol 671-674 ◽  
pp. 171-174
Author(s):  
Jian Feng Qi ◽  
Ying Yuan ◽  
Zht Wang
Keyword(s):  
Shear Stress ◽  
Shear Modulus ◽  
Dynamic Properties ◽  
Large Strain ◽  
Damping Ratio ◽  
Dynamic Shear Modulus ◽  
Dynamic Shear ◽  
Stress Strain ◽  
Strain Relation ◽  
Stress Strain Relation

Through a series of tests on saturated remoulded clay, initial shear stress on dynamic shear modulus and damping ratio under the condition of large strain(>10-3) is examined. The test data indicate that initial shear stress effects on stress-strain relation and dynamic modulus and damping ratio are obvious. With the initial shear stress increasing, the characteristic of the stress-strain relation changes from cyclic deformation to accumulative deformation, and there is difference in variation pattern of dynamic shear modulus and damping ratio with cyclic number increasing.

A Study on Dynamic Properties of Cement-Stabilized Soils

2011 ◽  
Vol 243-249 ◽  
pp. 2050-2054 ◽  
Author(s):  
Pei Hsun Tsai ◽  
Sheng Huoo Ni
Keyword(s):  
Shear Modulus ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Test Results ◽  
Resonant Column Test ◽  
Stabilized Soil ◽  
Shearing Strain ◽  
Relationship Of ◽  
The Relationship

In this paper the dynamic property (shear modulus and damping ratio) of cement-stabilized soil is studied with using the resonant column test. The amount of cement admixed, the magnitude of confining pressure, and shearing strain amplitude are the parameters considered. Test results show that the maximum shear modulus of cement-stabilized soil increases with increasing confining pressure, the minimum damping ratio decreases with increasing confining pressure. The shear modulus of cement-stabilized soil decreases with increasing shearing strain while the damping ratio increases with increasing shearing strain. In the paper the relationship of shear modulus versus shearing strain is fitted into the Ramberg-Osgood equations using regression analysis.

scholarly journals Characterization of the Dynamic Properties of Clay–Gravel Mixtures at Low Strain Level

2020 ◽  
Vol 12 (4) ◽  
pp. 1616 ◽  
Author(s):  
Xianwen Huang ◽  
Aizhao Zhou ◽  
Wei Wang ◽  
Pengming Jiang
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Mechanical Performance ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Strain Level ◽  
Dynamic Shear Modulus ◽  
Dynamic Shear ◽  
Gravel Content

In order to support the dynamic design of subgrade filling engineering, an experiment on the dynamic shear modulus (G) and damping ratio (D) of clay–gravel mixtures (CGMs) was carried out. Forty-two groups of resonant column tests were conducted to explore the effects of gravel content (0%, 10%, 20%, 30%, 40%, 50%, and 60%, which was the mass ratio of gravel to clay), gravel shape (round and angular gravels), and confining pressure (100, 200, and 300 kPa) on the dynamic shear modulus, and damping ratio of CGMs under the same compacting power. The test results showed that, with the increase of gravel content, the maximum dynamic shear modulus of CGMs increases, the referent shear strain increases linearly, and the minimum and maximum damping ratios decrease gradually. In CGMs with round gravels, the maximum dynamic shear modulus and the maximum damping ratio are greater, and the referent shear strain and the minimum damping ratio are smaller, compared to those with angular gravels. With the increase of confining pressure, the maximum dynamic shear modulus and the referent shear strain increase nonlinearly, while the minimum and maximum damping ratios decrease nonlinearly. The predicting equation for the dynamic shear modulus and the damping ratio of CGMs when considering confining pressure, gravel content, and shape was established. The results of this research may put forward a solid foundation for engineering design considering low-strain-level mechanical performance.

Shear modulus reduction and damping ratio curves for earth core materials of dams

2019 ◽  
Vol 56 (1) ◽  
pp. 14-22 ◽  
Author(s):  
DongSoon Park ◽  
Tadahiro Kishida
Keyword(s):  
Shear Modulus ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Empirical Relationship ◽  
Embankment Dams ◽  
In Situ Data ◽  
Earth Core ◽  
Dynamic Analyses ◽  
Modulus Reduction ◽  
Core Materials

It is essential to obtain shear modulus reduction and damping ratio curves to perform dynamic analyses of earth-cored embankment dams. Many studies have been performed for dynamic properties of clayey soils, but they have been limited for earth core materials of dams. This study conducted resonant column tests to obtain shear modulus reduction (G/Gmax) and damping ratio (D) curves for 31 specimens (17 undisturbed and 14 remolded specimens) from 13 earth-cored embankment dams. Empirical G/Gmax and D curves are proposed for dynamic properties of clayey earth core materials. Fitting curves are provided by using the functional forms of the Ramberg–Osgood and Darendeli models. The observation shows that the undisturbed earth cores yield relatively higher G/Gmax and lower D curves than the remolded cores. G/Gmax curves of compacted earth cores are relatively higher than those of Vucetic and Dobry curves for a similar level of plasticity index. Uncertainty and bias are calculated by performing residual analysis, which shows that there is no clear bias in predicting G/Gmax and the uncertainties between undisturbed earth core materials and natural deposits are at a similar level. A proposed empirical relationship of G/Gmax and D curves for earth core materials can be utilized for dynamic analyses of embankment dams for cases where there is insufficient in situ data.

Structure characteristics and mechanical properties of kaolinite soils. II. Effects of structure on mechanical properties

2006 ◽  
Vol 43 (6) ◽  
pp. 601-617 ◽  
Author(s):  
Y -H Wang ◽  
W -K Siu
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Shear Modulus ◽  
Critical State ◽  
Soil Structure ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Undrained Shear Strength ◽  
Interparticle Forces ◽  
Undrained Shear

This paper reports the effects of structure on the mechanical responses of kaolinite with known and controlled fabric associations. The dynamic properties and strength were assessed by resonant column tests and undrained triaxial compression tests, respectively. The experimental results demonstrate that interparticle forces and associated fabric arrangements influence the volumetric change under isotropic compression. Soils with different structures have individual consolidation lines, and the merging trend is not readily seen under an isotropic confinement up to 250 kPa. The dynamic properties of kaolinite were found to be intimately related to the soil structure. Stronger interparticle forces or higher degrees of flocculated structure lead to a greater small-strain shear modulus, Gmax, and a lower associated damping ratio, Dmin. The soil structure has no apparent influence on the critical-state friction angle (ϕ′c = 27.5°), which suggests that the critical stress ratio does not depend on interparticle forces. The undrained shear strength of kaolinite is controlled by its initial packing density rather than by any interparticle attractive forces, and yet the influence of the structure on the effective stress path is obvious.Key words: interparticle forces, shear modulus, damping ratio, stress–strain behavior, undrained shear strength, critical state.

DEGRADATION EFFECT OF SEAWATER ON THE LONG-TERM DYNAMIC BEHAVIOR OF ARTIFICIALLY CEMENTED SAND

2013 ◽  
Vol 07 (04) ◽  
pp. 1350031 ◽  
Author(s):  
BO LI ◽  
YUANQIANG CAI ◽  
XIANGWU ZENG ◽  
LINYOU PAN
Keyword(s):  
Shear Modulus ◽  
Dynamic Behavior ◽  
Tap Water ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Resonant Column ◽  
Cyclic Triaxial Tests ◽  
Cemented Sand

The dynamic behavior of lightly cemented sand under long-term seawater attack was evaluated in this study. Resonant column and cyclic triaxial tests were employed to investigate the evolution of the shear modulus and damping ratio of cemented sand with respect to soaking period (SP), confining pressure, and cement content (CC). The results of this study show that the cementation of the sand is affected by soaking in seawater to a greater extent than by soaking in tap water. The shear modulus of the cemented sand soaked in seawater was smaller than that of the cemented sand soaked in tap water. The damping ratio increased significantly, as the SP increased and was greater for the cemented sand soaked in seawater than for the cemented sand soaked in tap water. The dynamic behavior of nonhomogenous specimens was examined. Crystallization of salts could be clearly observed and probably explains the evolution of the dynamic behavior of the cemented sand. Finally, the shear modulus was fitted using Rollins' Law [Rollins et al., 1998], which demonstrates that the parameters used in the equation can be reasonably fitted linearly over a range of SPs.

Sign in / Sign up

Export Citation Format

Share Document