scholarly journals Pencil-on-Paper Sensor for Water Detection

2018 ◽  
Vol 2018 ◽  
pp. 1-5
Author(s):  
Zhiyuan Zhu ◽  
Kequan Xia ◽  
Zhiwei Xu ◽  
Hongze Zhang
Keyword(s):  
Water Detection ◽  
Potential Applications ◽  
Water Sensor ◽  
Paper Sensor ◽  
Immense Potential

This paper sets out a simple and affordable method for the manufacture of a water sensor involving drawing marks on paper using a flexible pencil. The sensor indicates flexible endurance variations upon exposure to water or a drying surface. It can be employed for the detection of water substances in ethanol. In addition, an experiment suggests the usefulness of the sensor for the sensing of breath. This shows the immense potential applications of the sensor for wearable and also health-inspecting electronic gadgetry.

scholarly journals Potential of Cyanobacteria in Wound Healing

2021 ◽  
Author(s):  
Laxmi Parwani ◽  
Mansi Shrivastava ◽  
Jaspreet Singh
Keyword(s):  
Wound Healing ◽  
Bioactive Compounds ◽  
Wound Care ◽  
Cost Effective ◽  
Wound Dressings ◽  
Potential Applications ◽  
Healing Agent ◽  
The Rich ◽  
Immense Potential ◽  
Insight Into

The wound care market is rapidly expanding due to the development of innumerable dressings that exhibit specific healing requirements for different wound types. The use of biomaterials as suitable wound dressing material is highly advantageous due to their biocompatibility, biodegradability, and non-toxicity. Cyanobacteria have been widely explored for their potential applications in wound healing, as they are the rich source of bioactive compounds with antibacterial, antitumor, antiviral, antioxidant, and antifungal activities. In recent years this group of organisms has been widely studied due to their immense potential in biomedical applications. Although their different bioactivities can support wound healing in different ways, very few forms have proven utility as a wound-healing agent. This chapter gives an insight into the potential of cyanobacteria in wound healing. Different bioactive compounds present in variable forms of cyanobacteria and their associated activities were reported to support tissue regeneration and wound healing acceleration. As the demand for cost-effective, bioactive wound care products is ever increasing, these organisms have immense potential to be utilized for the development of bioactive wound dressings. Hence, various bioactive compounds of cyanobacteria, their associated activities, and roles in wound healing have been briefly reviewed in this chapter.

scholarly journals Alkalophilic Protease Producing Bacteria and Some Biotechnological Potentials

2021 ◽  
Vol 11 (2) ◽  
Author(s):  
Muddasir Hassan Abbasi ◽  
Rabia Mehmood ◽  
Muhammad Babar Khawar ◽  
Hafiza Nabeela Amaan ◽  
Amin Arif ◽  
...  
Keyword(s):  
Web Of Science ◽  
Soda Lakes ◽  
Genus Bacillus ◽  
Microbial Life ◽  
Biotechnological Products ◽  
Other Substances ◽  
Potential Applications ◽  
Growth Requirement ◽  
Micro Organisms ◽  
Immense Potential

Background: Extremophiles are a hot topic in the field of biotechnology for their immense potential and applications in multiple industries. Objectives: The present review aims to sum up the potential applications of alkalophilic protease-producing bacteria and their optimized growth requirement. The isolation, characterization, and optimization of various isolates (especially of genus Bacillus) from different harsh niches, including soil samples from deserts and soil having decaying matters, wastewaters from industries, soda lakes, and alkaline springs have been reported in this review. Methodology: All the relevant papers published from 2013-2020 were looked over numerous sources like Google Scholar, Medline, PubMed, Research Gate, Science Direct, Scopus and Web of Science. Results: Most of the microbial life found in extreme alkaline habitats are found to form a variety of enzymes and an array of other substances of biotechnological interests. These enzymes, especially proteases, are exploited in industries globally because of their ability to withstand rigorous industrial reactions and conditions. Conclusion: Though a number of alkalophilic protease-producing bacteria have been isolated, still a large number of these micro-organisms are unidentified. The current demand for biotechnological products from them appeals to the need for isolation of unidentified bacteria.

scholarly journals Smart Blind Stick Design and Implementation

2021 ◽  
Vol 10 (5) ◽  
pp. 17-20
Author(s):  
Amira. A. Elsonbaty
Keyword(s):  
Wave Reflection ◽  
Electric Circuit ◽  
Phone Call ◽  
Electrical Circuits ◽  
Everyday Activities ◽  
Water Detection ◽  
Solid Objects ◽  
Water Sensor ◽  
Ultrasonic Wave Reflection ◽  
White Cane

Technologies are rapidly evolving, allowing people to live healthier and simpler lives. Sightless people are unable to carry out their everyday activities, such as walking down the street, visiting friends or relatives, or doing some other mundane tasks. As a result, the smart stick is a stick that can assist a person in walking safely without fear of colliding with another person or solid objects is proposed as a solution to this major issue. It is a development of the traditional blind stick as it acts as a companion for the blind when walking by sending audio alerts to the blind via a headphone connected to the phone with obstacles (water/walls/stairs / muddy ground) and also enables him to make a phone call to ask for help. EasyEda software was used for designing and simulating electrical circuits, was used to model the electric circuit. This system functions similarly to a white cane in that it assists blind people in scanning their surroundings for obstacles or orientation marks. This system will be mounted on a white cane with an ultrasonic sensor, and a water sensor to detect changes in the environment. Ultrasonic sensors detect obstacles in front of it using ultrasonic wave reflection, water detection sensors detect whether there is a puddle.

TEM characterization of reaction zone in a SiC fiber-reinforced titanium alloy

1988 ◽  
Vol 46 ◽  
pp. 738-739
Author(s):  
G. Das ◽  
R. E. Omlor
Keyword(s):  
Titanium Alloys ◽  
Reaction Zone ◽  
Carbon Layer ◽  
Fiber Reinforced ◽  
Reaction Products ◽  
Sic Fibers ◽  
Sic Fiber ◽  
The Matrix ◽  
Immense Potential

Fiber reinforced titanium alloys hold immense potential for applications in the aerospace industry. However, chemical reaction between the fibers and the titanium alloys at fabrication temperatures leads to the formation of brittle reaction products which limits their development. In the present study, coated SiC fibers have been used to evaluate the effects of surface coating on the reaction zone in the SiC/IMI829 system.IMI829 (Ti-5.5A1-3.5Sn-3.0Zr-0.3Mo-1Nb-0.3Si), a near alpha alloy, in the form of PREP powder (-35 mesh), was used a茸 the matrix. CVD grown AVCO SCS-6 SiC fibers were used as discontinuous reinforcements. These fibers of 142μm diameter contained an overlayer with high Si/C ratio on top of an amorphous carbon layer, the thickness of the coating being ∽ 1μm. SCS-6 fibers, broken into ∽ 2mm lengths, were mixed with IMI829 powder (representing < 0.1vol%) and the mixture was consolidated by HIP'ing at 871°C/0. 28GPa/4h.

An in situ and ex situ TEM study of the formation of thin cobalt silicide films by molecular beam epitaxy on the silicon (100) surface

1988 ◽  
Vol 46 ◽  
pp. 884-885
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove ◽  
R. T. Tung
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Defect Density ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Metal Base ◽  
In Situ Experiments ◽  
Potential Applications

The cobalt disilicide/silicon system has potential applications as a metal-base and as a permeable-base transistor. Although thin, low defect density, films of CoSi2 on Si(111) have been successfully grown, there are reasons to believe that Si(100)/CoSi2 may be better suited to the transmission of electrons at the silicon/silicide interface than Si(111)/CoSi2. A TEM study of the formation of CoSi2 on Si(100) is therefore being conducted. We have previously reported TEM observations on Si(111)/CoSi2 grown both in situ, in an ultra high vacuum (UHV) TEM and ex situ, in a conventional Molecular Beam Epitaxy system.The procedures used for the MBE growth have been described elsewhere. In situ experiments were performed in a JEOL 200CX electron microscope, extensively modified to give a vacuum of better than 10-9 T in the specimen region and the capacity to do in situ sample heating and deposition. Cobalt was deposited onto clean Si(100) samples by thermal evaporation from cobalt-coated Ta filaments.

Microstructure of laser-irradiated, conducting Kapton polyimide

1995 ◽  
Vol 53 ◽  
pp. 502-503
Author(s):  
D. L. Callahan ◽  
Z. Ball ◽  
H. M. Phillips ◽  
R. Sauerbrey
Keyword(s):  
Electron Microscopy ◽  
Phase Transition ◽  
Transmission Electron Microscopy ◽  
Cross Section ◽  
Film Surface ◽  
Cross Sectional ◽  
General Utility ◽  
Transmission Electron ◽  
Considerable Debate ◽  
Potential Applications

Ultraviolet laser-irradiation can be used to induce an insulator-to-conductor phase transition on the surface of Kapton polyimide. Such structures have potential applications as resistors or conductors for VLSI applications as well as general utility electrodes. Although the percolative nature of the phase transformation has been well-established, there has been little definitive work on the mechanism or extent of transformation. In particular, there has been considerable debate about whether or not the transition is primarily photothermal in nature, as we propose, or photochemical. In this study, cross-sectional optical microscopy and transmission electron microscopy are utilized to characterize the nature of microstructural changes associated with the laser-induced pyrolysis of polyimide.Laser-modified polyimide samples initially 12 μm thick were prepared in cross-section by standard ultramicrotomy. Resulting contraction in parallel to the film surface has led to distortions in apparent magnification. The scale bars shown are calibrated for the direction normal to the film surface only.

Fabrication and characterization - by High Resolution Electron Microscopy and atom probe microanalysis - of Co-based metallic multilayer films

1990 ◽  
Vol 48 (4) ◽  
pp. 772-773
Author(s):  
Amanda K. Petford-Long ◽  
A. Cerezo ◽  
M.G. Hetherington
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
High Resolution Electron Microscopy ◽  
Atom Probe ◽  
Multilayer Films ◽  
Interface Roughness ◽  
Probe Field ◽  
Resolution Electron ◽  
Potential Applications ◽  
Field Ion Microscope

The fabrication of multilayer films (MLF) with layer thicknesses down to one monolayer has led to the development of materials with unique properties not found in bulk materials. The properties of interest depend critically on the structure and composition of the films, with the interfacial regions between the layers being of particular importance. There are a number of magnetic MLF systems based on Co, several of which have potential applications as perpendicular magnetic (e.g Co/Cr) or magneto-optic (e.g. Co/Pt) recording media. Of particular concern are the effects of parameters such as crystallographic texture and interface roughness, which are determined by the fabrication conditions, on magnetic properties and structure.In this study we have fabricated Co-based MLF by UHV thermal evaporation in the prechamber of an atom probe field-ion microscope (AP). The multilayers were deposited simultaneously onto cobalt field-ion specimens (for AP and position-sensitive atom probe (POSAP) microanalysis without exposure to atmosphere) and onto the flat (001) surface of oxidised silicon wafers (for subsequent study in cross-section using high-resolution electron microscopy (HREM) in a JEOL 4000EX. Deposi-tion was from W filaments loaded with material in the form of wire (Co, Fe, Ni, Pt and Au) or flakes (Cr). The base pressure in the chamber was around 8×10−8 torr during deposition with a typical deposition rate of 0.05 - 0.2nm/s.

Progress and perspectives on halide lithium conductors for all-solid-state lithium batteries

2020 ◽  
Vol 13 (5) ◽  
pp. 1429-1461 ◽  
Author(s):  
Xiaona Li ◽  
Jianwen Liang ◽  
Xiaofei Yang ◽  
Keegan R. Adair ◽  
Changhong Wang ◽  
...  
Keyword(s):  
Energy Storage ◽  
Solid State ◽  
Lithium Batteries ◽  
Electrochemical Stability ◽  
Superionic Conductors ◽  
Fundamental Understanding ◽  
Potential Applications ◽  
Synthesis Routes

This review focuses on fundamental understanding, various synthesis routes, chemical/electrochemical stability of halide-based lithium superionic conductors, and their potential applications in energy storage as well as related challenges.

Porphyrin-functionalized coordination star polymers and their potential applications in photodynamic therapy

2019 ◽  
Vol 10 (45) ◽  
pp. 6116-6121 ◽  
Author(s):  
Tan Ji ◽  
Lei Xia ◽  
Wei Zheng ◽  
Guang-Qiang Yin ◽  
Tao Yue ◽  
...  
Keyword(s):  
Photodynamic Therapy ◽  
Self Assembly ◽  
Star Polymers ◽  
New Family ◽  
Potential Applications

We present a new family of porphyrin-functionalized coordination star polymers prepared through combination of coordination-driven self-assembly and post-assembly polymerization. Their self-assembly behaviour in water and potential for photodynamic therapy were demonstrated.

A peek in the micro-sized world: a review of design principles, engineering tools, and applications of engineered microbial community

2020 ◽  
Vol 48 (2) ◽  
pp. 399-409
Author(s):  
Baizhen Gao ◽  
Rushant Sabnis ◽  
Tommaso Costantini ◽  
Robert Jinkerson ◽  
Qing Sun
Keyword(s):  
Microbial Community ◽  
Microbial Communities ◽  
Environmental Remediation ◽  
Real Life ◽  
Design Principles ◽  
Microbial Interactions ◽  
Potential Applications ◽  
New Gene ◽  
Global Biogeochemical Cycles ◽  
Synthetic Microbial Communities

Microbial communities drive diverse processes that impact nearly everything on this planet, from global biogeochemical cycles to human health. Harnessing the power of these microorganisms could provide solutions to many of the challenges that face society. However, naturally occurring microbial communities are not optimized for anthropogenic use. An emerging area of research is focusing on engineering synthetic microbial communities to carry out predefined functions. Microbial community engineers are applying design principles like top-down and bottom-up approaches to create synthetic microbial communities having a myriad of real-life applications in health care, disease prevention, and environmental remediation. Multiple genetic engineering tools and delivery approaches can be used to ‘knock-in' new gene functions into microbial communities. A systematic study of the microbial interactions, community assembling principles, and engineering tools are necessary for us to understand the microbial community and to better utilize them. Continued analysis and effort are required to further the current and potential applications of synthetic microbial communities.

Sign in / Sign up

Export Citation Format

Share Document