scholarly journals Evaluations of Fracture Injection Pressure and Fracture Mouth Width during Separate-Layer Fracturing with Temporary Plugging

2018 ◽  
Vol 2018 ◽  
pp. 1-16
Author(s):  
Bo Wang ◽  
Fujian Zhou ◽  
Tianbo Liang ◽  
Daobing Wang ◽  
Liyang Gao ◽  
...  
Keyword(s):  
Tensile Strength ◽  
High Efficiency ◽  
Cohesive Zone Model ◽  
Low Cost ◽  
Injection Pressure ◽  
Injection Rate ◽  
Zone Model ◽  
Multiple Layer ◽  
Separate Layer ◽  
Mouth Width

Separate-layer fracturing with temporary plugging (SLFTP) is a potential way to stimulate multiple layer reservoirs due to its low cost, low risk, and high efficiency. In this study, based on the cohesive zone model (CZM), a 3D fully fluid-solid coupling and multiple layer model is established to investigate factors influencing fracture injection pressure and fracture mouth width. The cohesive layer properties are based on the reported study, which have been validated through a series of numerical experiments. Innovatively, the spring model is innovatively proposed to represent the plugging effect of diverting agents and prop the aperture of the previous fractures. Simulation results reveal that the effects of previous fractures in multiple layer formations can be neglected, which is quite different from multistage fracturing for horizontal wells. Fracture injection pressure can be evaluated more accurately by taking the following factors into consideration: the minimum horizontal principal stress, rock tensile strength, injection rate, and pore pressure enhancement. Further, fracture mouth width is strongly influenced by rock tensile strength, Young’s modulus, and injection rate. This study provides a guidance for candidate well selection and diverting agent optimization during SLFTP in multilayer formations.

The quantitative analysis of tensile strength of additively manufactured continuous carbon fiber reinforced polylactic acid (PLA)

2019 ◽  
Vol 25 (10) ◽  
pp. 1624-1636 ◽  
Author(s):  
Hongbin Li ◽  
Taiyong Wang ◽  
Sanjay Joshi ◽  
Zhiqiang Yu
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Fracture Mechanism ◽  
Cohesive Zone ◽  
Cohesive Zone Model ◽  
Zone Model ◽  
Fiber Reinforced ◽  
Continuous Fiber ◽  
Content Type ◽  
Continuous Carbon Fiber

Purpose Continuous fiber-reinforced thermoplastic composites are being widely used in industry, but the fundamental understanding of their properties is still limited. The purpose of this paper is to quantitatively study the effects of carbon fiber content on the tensile strength of continuous carbon fiber-reinforced polylactic acid (CCFRPLA) fabricated through additive manufacturing using the fused deposition modeling (FDM) process. Design/methodology/approach The strength of these materials is highly dependent on the interface that forms between the continuous fiber and the plastic. A cohesive zone model is proposed as a theoretical means to understand the effect of carbon fiber on the tensile strength properties of CCFRPLA. The interface formation mechanism is explored, and the single fiber pulling-out experiment is implemented to investigate the interface properties of CCFRPLA. The fracture mechanism is also explored by using the cohesive zone model. Findings The interface between carbon fiber and PLA plays the main role in transferring external load to other fibers within CCFRPLA. The proposed model established in this paper quantitatively reveals the effects of continuous carbon fiber on the mechanical properties of CCFRPLA. The experimental results using additively manufacturing CCFRPLA provide validation and explanation of the observations based on the quantitative model that is established based on the micro-interface mechanics. Research limitations/implications The predict model is established imagining that all the fibers and PLA form a perfect interface. While in a practical situation, only the peripheral carbon fibers of the carbon fiber bundle can fully infiltrate with PLA and form a transmission interface. These internal fibers that cannot contract with PLA fully, because of the limit space of the nozzle, will not form an effective interface. Originality/value This paper theoretically reveals the fracture mechanism of CCFRPLA and provides a prediction model to estimate the tensile strength of CCFRPLA with different carbon fiber contents.

scholarly journals A Numerical and Experimental Study of Adhesively-Bonded Polyethylene Pipelines

Polymers ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1531 ◽  
Author(s):  
Guilpin ◽  
Franciere ◽  
Barton ◽  
Blacklock ◽  
Birkett
Keyword(s):  
Cohesive Zone ◽  
Adhesive Bonding ◽  
Structural Integrity ◽  
Cohesive Zone Model ◽  
Low Cost ◽  
Element Model ◽  
Zone Model ◽  
Adhesively Bonded ◽  
Lap Shear ◽  
Lap Shear Test

Adhesive bonding of polyethylene gas pipelines is receiving increasing attention as a replacement for traditional electrofusion welding due to its potential to produce rapid and low-cost joints with structural integrity and pressure tight sealing. In this paper a mode-dependent cohesive zone model for the simulation of adhesively bonded medium density polyethylene (MDPE) pipeline joints is directly determined by following three consecutive steps. Firstly, the bulk stress–strain response of the MDPE adherend was obtained via tensile testing to provide a multi-linear numerical approximation to simulate the plastic deformation of the material. Secondly, the mechanical responses of double cantilever beam and end-notched flexure test specimens were utilised for the direct extraction of the energy release rate and cohesive strength of the adhesive in failure mode I and II. Finally, these material properties were used as inputs to develop a finite element model using a cohesive zone model with triangular shape traction separation law. The developed model was successfully validated against experimental tensile lap-shear test results and was able to accurately predict the strength of adhesively-bonded MPDE pipeline joints with a maximum variation of <3%.

The Impacts of Increased Ductility in Organic-Rich Shale on Fracture Network Growth by Hydraulic Fracturing

2021 ◽  
Author(s):  
Chang Huang ◽  
Shengli Chen
Keyword(s):  
Tensile Strength ◽  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Cohesive Zone ◽  
Cohesive Zone Model ◽  
Fracture Network ◽  
Cohesive Crack ◽  
Hydraulic Fractures ◽  
Zone Model ◽  
Fully Coupled

Abstract The difficulty of hydraulic fracturing in organic-rich shale caused by the increased ductility has not been well interpreted quantitatively, although it is well perceived that the increased shale ductility can impede the propagation of hydraulic fractures and enhance the healing of created fractures upon injection shutdown. This study aims to quantitatively study the impacts of increased ductility on the stimulated reservoir volume (SRV) using an advanced XFEM-based simulator. To achieve this goal, a modified cohesive zone model has been integrated into an in-house fully coupled poroelastic XFEM framework. The study continues by extending the functionality of the numerical framework to simulating multiple interacting fractures. The utilization of the object-oriented programming paradigm in the development of the framework makes it an easy extension to include the multi-fracture network by creating more instances of crack segments. A main hydraulic fracture with an arbitrary number of intersected branches can thus be modeled. A series of parametric studies will be conducted to investigate the impacts of increased ductility on the induced SRV by varying four involved material parameters individually. The modified cohesive zone model, which is essentially a traction-separation law (TSL), is characterized by four parameters: the initial tensile strength Tini, ultimate tensile strength Tkrg, the critical separation Dc, and the final crack separation Dmax. It can flexibly model different crack opening scenarios and simulate more realistically the increased shale ductility. The fully coupled poroelastic XFEM framework has been comprehensively verified against the latest semi-analytical solutions on the four well-known propagation regimes. The numerical results show that the shape of TSL does affect the main hydraulic fracture growth as well as the evolvement of the fracture network, given the same cohesive crack energy and tensile strength. It infers that ductility is not only controlled by cohesive crack energy and tensile strength, which further indicates the necessity of the newly proposed cohesive zone model. The magnitude of the initial tensile strength, controlling when the cohesive crack starts propagating, is found to have the greatest impacts on the fracture length, and SRV, among all four TSL parameters. The novelty of this study is two-fold. First, the newly modified cohesive zone model can more realistically represent the increased shale ductility. Second, the advanced XFEM framework that enables the simulation of a fracture network can study the impacts of increased ductility on the whole SRV but not a single crack.

scholarly journals Investigation of Adhesive’s Material in Hermetic MEMS Package for Interfacial Crack between the Silver Epoxy and the Metal Lid during the Precondition Test

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5626
Author(s):  
Mei-Ling Wu ◽  
Jia-Shen Lan
Keyword(s):  
Internal Pressure ◽  
Cohesive Zone Model ◽  
Experimental Testing ◽  
Low Cost ◽  
Interfacial Crack ◽  
Bonding Layer ◽  
Zone Model ◽  
Micro Electro Mechanical Systems ◽  
Epoxy Material ◽  
Silver Epoxy

A hermetic Micro-Electro-Mechanical Systems (MEMS) package with a metal lid is investigated to prevent lid-off failure and improve its reliability during the precondition test. While the MEMS package benefits from miniaturization and low cost, a hermetic version is highly sensitive to internal pressure caused by moisture penetration and the reflow process, thus affecting its reliability. In this research, the finite element method is applied to analyze the contact stress between the metal lid and the silver epoxy by applying the cohesive zone model (CZM). Moreover, the red dye penetration test is applied, revealing a microcrack at the metal lid/silver epoxy interface. Further analyses indicate that the crack is caused by internal pressure. According to the experimental testing and simulation results, the silver epoxy material, the curing process, the metal lid geometry, and the bonding layer contact area can enhance the bonding strength between the metal lid and the substrate.

scholarly journals The Responses of Injection Pressure and Fracture Width during Height Extension in Sand-Mud Interbed Reservoirs in the Dongsheng Gas Field

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Di Wang ◽  
Haibo Wang ◽  
Fengxia Li ◽  
Fuhu Chen ◽  
Xinchun Zhu
Keyword(s):  
Cohesive Zone Model ◽  
Early Period ◽  
Coupled Model ◽  
Vertical Direction ◽  
Injection Pressure ◽  
High Viscosity ◽  
Zone Model ◽  
Gas Field ◽  
Fracture Width ◽  
Fracture Height

The Dongsheng gas field is characterized by low porosity and low permeability. Its principal producing reservoir is the H-1 zone, belonging to the Lower Shihezi Formation. Sand is the main lithology in the H-1 zone, while mud interlayers are also well developed in a vertical direction. As a result, the reservoir is a sand-mud interbed, which brings difficulty to fracture height extension. In order to understand the process of fracture height growth in a sand-mud interbed reservoir and obtain the responses of injection pressure and fracture width during a hydraulic fracturing, a hydromechanical-coupled model is established. Mud interlayers are fully considered and a cohesive zone model is adopted to deal with fracture propagation. Numerical results show that the fracture extends quickly to the sand-mud interface after initiation and breaks through rather than propagating along the interfaces. Pressure and width both increase continuously when fracture propagates in the mud interlayer. High-viscosity and high-injection rates are helpful for the fracture to break through the mud interlayer, especially at an early period. When the mud interlayers are asymmetric, pressure and width fluctuate several times once fracture propagates inside and breaks through the mud interlayer. Perforations close to the thinner mud interlayer can increase the fracture width and reduce fracturing risks.

Influence of MBE Growth Conditions on Dislocation Densities of GaAs/Ge Epilayers Grown on Silicon Substrates

1985 ◽  
Vol 43 ◽  
pp. 364-365
Author(s):  
K.M. Hones ◽  
P. Sheldon ◽  
B.G. Yacobi ◽  
A. Mason
Keyword(s):  
High Efficiency ◽  
Lattice Mismatch ◽  
Low Cost ◽  
Growth Conditions ◽  
Nonradiative Recombination ◽  
Device Structure ◽  
Si Substrates ◽  
Transmission Electron ◽  
Dislocation Densities ◽  
Dislocation Type

There is increasing interest in growing epitaxial GaAs on Si substrates. Such a device structure would allow low-cost substrates to be used for high-efficiency cascade- junction solar cells. However, high-defect densities may result from the large lattice mismatch (∼4%) between the GaAs epilayer and the silicon substrate. These defects can act as nonradiative recombination centers that can degrade the optical and electrical properties of the epitaxially grown GaAs. For this reason, it is important to optimize epilayer growth conditions in order to minimize resulting dislocation densities. The purpose of this paper is to provide an indication of the quality of the epitaxially grown GaAs layers by using transmission electron microscopy (TEM) to examine dislocation type and density as a function of various growth conditions. In this study an intermediate Ge layer was used to avoid nucleation difficulties observed for GaAs growth directly on Si substrates. GaAs/Ge epilayers were grown by molecular beam epitaxy (MBE) on Si substrates in a manner similar to that described previously.

Integrated Technologies of Testing and Controlling for High Efficiency Separate Layer Water Injection

2008 ◽  
Author(s):  
He Liu ◽  
Danfeng Xiao ◽  
Li Zhi Zhao ◽  
Fukun Zhang ◽  
Yumei Wang ◽  
...  
Keyword(s):  
High Efficiency ◽  
Water Injection ◽  
Separate Layer

Improvement of Ti/RuO2–IrO2 Anode Lifetime and Electrocatalytical Properties by Using an Eco-Friendly Thermal Decomposition Method Using Polyvinyl Alcohol as Solvent

2019 ◽  
Author(s):  
Charlys Bezerra ◽  
Géssica Santos ◽  
Marilia Pupo ◽  
Maria Gomes ◽  
Ronaldo Silva ◽  
...  
Keyword(s):  
Thermal Decomposition ◽  
Polyvinyl Alcohol ◽  
High Efficiency ◽  
Electrochemical Impedance ◽  
Pechini Method ◽  
Low Cost ◽  
Charge Transfer Resistance ◽  
Transfer Resistance ◽  
Calcination Temperatures ◽  
Service Lifetime

<p>Electrochemical oxidation processes are promising solutions for wastewater treatment due to their high efficiency, easy control and versatility. Mixed metal oxides (MMO) anodes are particularly attractive due to their low cost and specific catalytic properties. Here, we propose an innovative thermal decomposition methodology using <a>polyvinyl alcohol (PVA)</a> as a solvent to prepare Ti/RuO<sub>2</sub>–IrO<sub>2</sub> anodes. Comparative anodes were prepared by conventional method employing a polymeric precursor solvent (Pechini method). The calcination temperatures studied were 300, 400 and 500 °C. The physical characterisation of all materials was performed by X-ray diffraction and scanning electron microscopy coupled with energy dispersive spectroscopy, while electrochemical characterisation was done by cyclic voltammetry, accelerated service lifetime and electrochemical impedance spectroscopy. Both RuO<sub>2</sub> and IrO<sub>2</sub> have rutile-type structures for all anodes. Rougher and more compact surfaces are formed for the anodes prepared using PVA. Amongst temperatures studied, 300 °C using PVA as solvent is the most suitable one to produce anodes with expressive increase in voltammetric charge (250%) and accelerated service lifetime (4.3 times longer) besides reducing charge-transfer resistance (8 times lower). Moreover, the electrocatalytic activity of the anodes synthesised with PVA toward the Reactive Blue 21 dye removal in chloride medium (100 % in 30 min) is higher than that prepared by Pechini method (60 min). Additionally, the removal total organic carbon point out improved mineralisation potential of PVA anodes. Finally, this study reports a novel methodology using PVA as solvent to synthesise Ti/RuO<sub>2</sub>–IrO<sub>2</sub> anodes with improved properties that can be further extended to synthesise other MMO compositions.</p>

Contradiction Analysis and Solution in the R&D of High-Power Solar LED Street Lamp Controller

2019 ◽  
Vol 12 (1) ◽  
pp. 12-19
Author(s):  
Zhengwang Xu ◽  
Wei Mei ◽  
Jiaqi Yu ◽  
Jiarui Zhang ◽  
Yuchun Yi ◽  
...  
Keyword(s):  
Power Supply ◽  
High Efficiency ◽  
Low Cost ◽  
Solar Panel ◽  
Battery Voltage ◽  
Supply Circuit ◽  
Led Light ◽  
Power Supply Circuit ◽  
Side Mode ◽  
Dual Power

As being restricted by factors such as cost, efficiency and size, the development of high-power solar LED street light controller is faced with plenty of difficulties. In case that a structure of two independent DC/DC is applied as the main circuit, it has to face problems such as large size and high cost; in case of applying the bidirectional BUCK/BOOST circuit, it requires change-over switches to control the solar panel and LED light. As being restricted by withstanding voltage, on-resistance and cost, a PMOS device cannot be used as the change-over switch of solar panel and LED light. However, when being used as a change-over switch, an NMOS device must apply the low-side mode under which the negative ends of the mentioned three parts are cut off. In the condition of applying the low-side mode, a differential circuit must be used to detect the voltage of the solar panel. Furthermore, in order to make sure batteries can still be regularly charged after wearing out in daylight, the controller must be supplied with power through a dual power supply circuit that can obtain power from both the solar panel and the battery. The demander has a requirement on extremely low standby power consumption of the product, and thus it is necessary to minimize the circuit that is live while working in standby mode. Methods: The bidirectional BUCK/BOOST circuit structure is applied to the main circuit to realize a higher change-over efficiency while giving considerations to both cost and size. The NMOS device, model IRFB4410ZPBF, with a price of about three yuan, is used as the switching device, and the low-side mode is applied, that is the switches inserted in between negative end of the solar panel or LED light and that of the DC/DC circuit. The low-cost rail-to-rail operational amplifier LM358 is used to form a differential amplification circuit for detecting the voltage of the solar panel. A XL1509-12E1 chip that only costs 0.88 yuan/pc is selected as the main change-over chip for the power supply, which has realized the highly-efficient and low-cost change-over of the power supply. A dual power supply circuit and a step-down protective circuit are designed for the XL1509-12E1 change-over chip. By comparing solar panel voltage with battery voltage, the solar panel booting circuit is realized. Only when solar panel voltage is higher than battery voltage, does the system program start to power it up for running, so that the outage of most of the circuits of the system under standby mode does not consume energy. Furthermore, the solar panel voltage detecting circuit, the solar panel booting circuit and several return difference functions are corrected during system debugging. Results: The circuit board of the entire controller features small size, low cost and high efficiency. It measures about 100*62*18mm in size, costs about 60 yuan, and the charge/discharge change-over efficiency reaches up to over 95%. The controller has many functions: it is capable of operating within a large scope, in which, solar panel voltage is subject to 15~50V, LED light voltage is subject to 15~60V, battery voltage is subject to 10~35V and battery-end charge/discharge current is 10A; it is capable of adapting to monocrystalline silicon/multicrystalline silicon/thin-film and many other kinds of solar panels, as well as lithium/lead-acid and many other kinds of batteries; it is capable of detecting the conversion of day and night, automatically controlling charging and discharging and automatically making adaptive adjustment according to seasonal variations; the current to be consumed during standby will be maintained below 3mA, and thus the power consumption is extremely low. Conclusion: By selecting the bidirectional BUCK/BOOST circuit structure, applying low-side mode for switching of solar panel and LED light, using a differential circuit to detect solar panel voltage, using a low-cost DC/DC chip to realize power supply change-over, designing a dual power supply circuit, introducing solar panel booting circuit and other hardware design, as well as MPPT algorithm, state recognition and control, return difference control and other software design, a solar LED street light control product featuring small size, low cost, high efficiency and multiple functions is successfully developed.

Sign in / Sign up

Export Citation Format

Share Document