scholarly journals Flexural Assessment of Blast-Damaged RC Beams Retrofitted with CFRP Sheet and Steel Fiber

2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
Jin-Young Lee ◽  
Hyun-Oh Shin ◽  
Kyung-Hwan Min ◽  
Young-Soo Yoon
Keyword(s):  
Flexural Strength ◽  
Steel Fiber ◽  
Blast Resistance ◽  
Large Diameter ◽  
Small Diameter ◽  
Concrete Cover ◽  
Experimental Program ◽  
Fiber Reinforced ◽  
Cfrp Sheets ◽  
Original Strength

This study presents the effects of blast-induced local damages on the flexural strength of blast-damaged and repaired specimens. In the experimental program, blast-damaged specimens were repaired with steel fiber reinforced cementitious composite (SFRCC) as well as carbon fiber-reinforced polymer (CFRP) sheets and tested for flexural strength measurements. The test parameters included shear reinforcement (amount and spacing), steel fiber content (0, 1.0 vol%), and retrofitting with CFRP sheets. The test results indicated that the use of higher amounts of stirrups demonstrated insignificant benefits in preventing local damages. However, it was shown that the use of small-diameter steel bars for stirrups with small spacing could decrease the local damages more effectively compared to the large-diameter steel reinforcement. For the residual strength of the damaged specimens, the specimens using more stirrups could resist over 60% of their original flexural strength. CFRP retrofitting showed insignificant enhancement in ductility of intact, damaged, and repaired specimens. However, it distributed the blast load and protected debris scattering. The addition of steel fibers results in increased ductility and enhanced blast resistance against local damages. All specimens, excluding control specimen, that repaired with SFRCC showed higher flexural strength to their original strength. Therefore, it can be concluded that replacing damaged concrete cover with SFRCC is adequate for repairing the blast-damaged RC members.

scholarly journals An experimental study on flexural strengthening of RC beams using CFRP sheets

2018 ◽  
Vol 7 (4) ◽  
pp. 2075 ◽  
Author(s):  
Yasmin Murad
Keyword(s):  
Flexural Strength ◽  
Orientation Angle ◽  
Longitudinal Axis ◽  
Flexural Behavior ◽  
Experimental Program ◽  
Rc Beams ◽  
Rc Structures ◽  
Flexural Strengthening ◽  
Cfrp Sheets ◽  
Reinforced Polymer

 The use of carbon fiber reinforced polymer (CFRP) sheets is becoming a widely accepted solution for strengthening and repairing rein-forced concrete (RC) structures. To date, the behavior of RC beams, strengthened with 60˚ and 45˚ inclined CFRP sheets, has not clearly explained. An experimental program is proposed in this paper to investigate the flexural behavior of RC beams strengthened with CFRP sheets. CFRP sheets were epoxy bonded to the tension face to enhance the flexural strength of beams inducing different orientation angles of 0˚, 45˚, 60˚ and 90˚ with the beam longitudinal axis. The study shows that strengthening RC beams with CFRP sheets is highly influenced by the orientation angle of the sheets. The orientation angle plays a key role in changing the crack pattern and hence the failure mode. The influence of CFRP sheets was adequate on increasing the flexural strength of RC beams but the ductility of the beams was reduced. The best performance was obtained when strengthening RC beam obliquely using 45˚ inclined CFRP sheets where the specimen experienced additional deflection and strength of 56% and 12% respectively and the reduction in its ductility was the least. It is recom-mended to strengthen RC beams, which are weak in flexure, using 45˚ inclined CFRP sheets.  

Experimental Study on Rate-Dependent of the Bending Tensile Properties for Steel Fiber Reinforced Concrete

2011 ◽  
Vol 71-78 ◽  
pp. 1083-1089
Author(s):  
Zhang Luo
Keyword(s):  
Reinforced Concrete ◽  
Flexural Strength ◽  
Strain Rate ◽  
Tensile Properties ◽  
Steel Fiber ◽  
Fiber Reinforced Concrete ◽  
Test Machine ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Rate Dependent

Extensive experimental research has been done on rate-dependent properties normal concrete, but very little on the tensile properties of steel fiber reinforced concrete (SFRC). In this article, based on a high-speed Instron servo-controlled hydraulic materials test machine is adopted to investigate the strain rate-dependent properties of bending tensile properties for SFRC. The scheme of experiment, the works of specimens fabricating and the processes of both loading and measuring were introduced. A total of 30 beam specimens are tested. The steel fiber content is varied: 0%, 1.0%, 2.0%, 3.0% and 4.0% by volume. The experimental results were analyzed. The emphasis is put on the study of the flexural strength changes of SFRC under different strain rates. It is discovered that, with the improvement of the strain rate, increasing strength of SFRC is very obvious. While the strain rate increases from 1.4×10-4s-1 to 0.53×10-4s-1, the flexural strength increasing around 30%.

scholarly journals Using Steel Fiber-Reinforced Concrete Precast Panels for Strengthening in Shear of Beams: An Experimental and Analytical Investigation

2019 ◽  
Vol 2019 ◽  
pp. 1-18 ◽  
Author(s):  
Pitcha Jongvivatsakul ◽  
Linh V. H. Bui ◽  
Theethawachr Koyekaewphring ◽  
Atichon Kunawisarut ◽  
Narawit Hemstapat ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Fiber Reinforced Concrete ◽  
Experimental Program ◽  
Rc Beams ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Fiber Volume ◽  
Simple Formulation

In this paper, the performances of reinforced concrete (RC) beams strengthened in shear with steel fiber-reinforced concrete (SFRC) panels are investigated through experiment, analytical computation, and numerical analysis. An experimental program of RC beams strengthened by using SFRC panels, which were attached to both sides of the beams, is carried out to investigate the effects of fiber volume fraction, connection type, and number and diameter of bolts on the structural responses of the retrofitted beams. The current shear resisting model is also employed to discuss the test data considering shear contribution of SFRC panels. The experimental results indicate that the shear effectiveness of the beams strengthened by using SFRC panels is significantly improved. A three-dimensional (3D) nonlinear finite element (FE) analysis adopting ABAQUS is also conducted to simulate the beams strengthened in shear with SFRC panels. The investigation reveals the good agreement between the experimental and analytical results in terms of the mechanical behaviors. To complement the analytical study, a parametric study is performed to further evaluate the influences of panel thickness, compressive strength of SFRC, and bolt pattern on the performances of the beams. Based on the numerical and experimental analysis, a shear resisting model incorporating the simple formulation of average tensile strength perpendicular to the diagonal crack of the strengthened SFRC panels is proposed with the acceptable accuracy for predicting the shear contribution of the SFRC system under various effects.

Orthogonal Experimental Study on Properties of Hybrid Fiber Reinforced Cement Mortar

2010 ◽  
Vol 168-170 ◽  
pp. 456-459
Author(s):  
Hai Yan Yuan ◽  
Shui Zhang ◽  
Guo Zhong Li
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Steel Fiber ◽  
Cement Mortar ◽  
Polypropylene Fiber ◽  
Fiber Reinforced ◽  
Hybrid Fiber ◽  
Factors Affecting ◽  
Fiber Fraction ◽  
Reinforced Cement

By adopting the method of orthogonal experimental design, the effect of three independent variables, that is steel fiber fraction, polypropylene fiber fraction and silica fume fraction on the compressive strength, flexural strength and shrinkage of cement mortar was studied. The results indicate that steel fiber is one of the most important factors affecting compressive strength and shrinkage, and polypropylene fiber is one of the most important factors affecting flexural strength and shrinkage of cement mortar. By using deviation analysis to analyze the orthogonal experiment results, the optimized mix proportion of hybrid fiber reinforced cement mortar is determined. The hybrid effect of steel fiber and polypropylene fiber on the properties of cement mortar is discussed.

scholarly journals Optimization of the Fine to Coarse Aggregate Ratio for the Workability and Mechanical Properties of High Strength Steel Fiber Reinforced Concretes

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5202
Author(s):  
Mohammad Iqbal Khan ◽  
Wasim Abbass ◽  
Mohammad Alrubaidi ◽  
Fahad K. Alqahtani
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Steel Fiber ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Fresh State

High-strength concrete is used to provide quality control for concrete structures, yet it has the drawback of brittleness. The inclusion of fibers improves the ductility of concrete but negatively affects the fresh properties of fiber-reinforced concrete. The effects of different fine to coarse aggregate ratios on the fresh and hardened properties of steel fiber reinforced concrete were investigated in this study. Mixtures were prepared with various fine to coarse aggregate (FA/CA) ratios incorporating 1% steel fiber content (by volume) at constant water to cement ratio. The workability, unit weight, and temperature of the concrete in the fresh state, and the mechanical properties of steel-fiber-reinforced concrete (SFRC) were investigated. The inclusion of fiber in concrete influenced the mobility of concrete in the fresh state by acting as a barrier to the movement of coarse aggregate. It was observed that the concrete with an FA/CA ratio above 0.8 showed better flowability in the fresh state, whilst an above 0.9 FA/CA ratio requires excessive superplasticizer to maintain the flowability of the mixtures. The compressive and flexural strength of SFRC increased with an increase in the FA/CA ratio by around 10% and 28%, respectively. Experimental values of compressive strength and flexural strength showed good agreement, however, modulus of elasticity demonstrated slightly higher values. The experimentally obtained measurements of the mechanical properties of SFRC conformed reasonably well with the available existing prediction equations, and further enabled establishing predictive isoresponse interactive equations within the scope of the investigation domain.

Sign in / Sign up

Export Citation Format

Share Document