scholarly journals Structure and Properties of Hydrophobic Aggregation Hydrogel with Chemical Sensitive Switch

2017 ◽  
Vol 2017 ◽  
pp. 1-5 ◽  
Author(s):  
Jiufang Duan ◽  
Jianxin Jiang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Contact Angle ◽  
Weight Loss ◽  
Control Release ◽  
Structure And Properties ◽  
Maximum Value ◽  
Potential Applications ◽  
Hydrophobic Aggregation ◽  
Scanning Electron

Hydrogels with chemical sensitive switch have control release properties in special environments. A series of polyacrylamide-octadecyl methacrylate hydrogels crosslinked by N,N′-bis (acryloyl) cystamine were synthesized as potential chemical sensitive system. When this hydrogel encounters dithiothreitol it can change its quality. The properties of the hydrogels were characterized by infrared spectroscopy, contact angle, and scanning electron microscopy. The water absorption of the hydrogel has the maximum value of 475%, when the content of octadecyl methacrylate is 5 wt%. The amount of weight loss was changed from 34.6% to 17.2%, as the content of octadecyl methacrylate increased from 3 wt% to 9.4 wt%. At the same time, the stress of the hydrogel decreased from 67.01% to 47.61%; the strength of the hydrogel reaches to the maximum 0.367 Mpa at 7 wt% octadecyl methacrylate. The increasing content of octadecyl methacrylate from 3 wt% to 9.4 wt% can enhance the hydrophobicity of the hydrogel; the contact angle of water to hydrogel changed from 14.10° to 19.62°. This hydrogel has the porous structure which permits loading of oils into the gel matrix. The functionalities of the hydrogel make it have more widely potential applications in chemical sensitive response materials.

scholarly journals Viscoelastic Polyurethane Foam with Keratin and Flame-Retardant Additives

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1380
Author(s):  
Krystyna Wrześniewska-Tosik ◽  
Joanna Ryszkowska ◽  
Tomasz Mik ◽  
Ewa Wesołowska ◽  
Tomasz Kowalewski ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Thermal Resistance ◽  
Flame Retardant ◽  
Fire Resistance ◽  
Release Rate ◽  
Structure And Properties ◽  
Burning Behavior ◽  
Keratin Fibers ◽  
Scanning Electron

Viscoelastic polyurethane (VEPUR) foams with increased thermal resistance are presented in this article. VEPUR foams were manufactured with the use of various types of flame retardant additives and keratin fibers. The structure of the modified foams was determined by spectrophotometric-(FTIR), thermal-(DSC), and thermogravimetric (TGA) analyses as well as by scanning electron microscopy (SEM). We also assessed the fire resistance, hardness, and comfort coefficient (SAG factor). It was found that the use of keratin filler and flame retardant additives changed the foams’ structure and properties as well as their burning behavior. The highest fire resistance was achieved for foams containing keratin and expanding graphite, for which the reduction in heat release rate (HRR) compared to VEPUR foams reached 75%.

scholarly journals Corrosion Inhibitive Action and Adsorption Behaviour of Justicia Secunda Leaves Extract as an Eco‐Friendly Inhibitor for Aluminium in Acidic Media

2021 ◽  
Vol 11 (5) ◽  
pp. 13019-13030
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Weight Loss ◽  
Electrochemical Impedance ◽  
Physical Adsorption ◽  
Charge Transfer Resistance ◽  
Aluminum Surface ◽  
Protective Film ◽  
Transfer Resistance ◽  
Scanning Electron

The extract of Justicia secunda (JS) leaves was investigated as an eco‐friendly corrosion inhibitor of aluminum in 0.5 M HCl using weight loss, electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and scanning electron microscopy (SEM) techniques. The inhibitor concentrations used ranged from 50 to 250 ppm at 30, 40, and 50oC. Results show that Justicia secunda acts as a good inhibitor for aluminum. Its efficiency increased with increasing inhibitor concentration but decreased with increasing temperature. Maximum inhibition efficiency as high as 94.3% was found at 30°C for 250 ppm of the inhibitor with the weight loss technique. Tafel polarization results show that the extract acts as a mixed-type inhibitor. The Nyquist plots indicated decreasing double-layer capacitance and increasing charge transfer resistance on increasing JS concentration. The inhibition action occurred through the physical adsorption of the extract on the aluminum surface. The adsorption process was found to follow Langmuir adsorption isotherm. The formation of a protective film on the metal surface was confirmed by scanning electron microscopy.

Influence of the Treatment with Sulfuric Acid on Adhesion of Natural Rubber and Cast Polyurethane Elastomers

2012 ◽  
Vol 452-453 ◽  
pp. 86-90 ◽  
Author(s):  
Zhi Yi Zhang ◽  
Hui Jun Niu ◽  
Jia Jia Zhang ◽  
Yan Yun Cui
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Contact Angle ◽  
Sulfuric Acid ◽  
Natural Rubber ◽  
Angle Measurement ◽  
Polyurethane Elastomers ◽  
Adhesion Properties ◽  
Rubber Surface ◽  
Scanning Electron

In this study, natural rubber (NR) was treated with sulfuric acid to improve its adhesion properties to polar polymer. T-peel strength tests, scanning electron microscopy, contact-angle measurement (water), Energy Dispersive X-ray Detector were used to analyze the nature of the NR surface modifications which were carried out with sulfuric acid. A noticeable decrease in contact angle was observed on the rubber surface by contact-angle measurements which can be ascribed to the increase of oxidized moieties on the rubber surface. EDX revealed that oxidized moieties were created through treatment with sulfuric acid. The surface modification and mode of bond failure were studied by scanning electron microscopy (SEM). Immersion in sulfuric acid for 15min produced the maximum adhesion strength (10kN/m) and produced a mixed failure mode (interface & rubber failure in the rubber). Treatment with sulfuric acid produced improved wettability as well as chemical (surface oxidation) and morphological modifications (roughness) of the rubber surface.

scholarly journals Preparation and Characterization of K-Carrageenan/Nanosilica Biocomposite Film

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Lokesh R. Rane ◽  
Niranjan R. Savadekar ◽  
Pravin G. Kadam ◽  
Shashank T. Mhaske
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Contact Angle ◽  
Tensile Strength ◽  
Water Vapour ◽  
Transmission Rate ◽  
Composite Films ◽  
Tensile Modulus ◽  
Water Vapour Transmission Rate ◽  
Scanning Electron

The purpose of this study is to improve the performance properties of K-carrageenan (K-CRG) by utilizing nanosilica (NSI) as the reinforcing agent. The composite films were prepared by solution casting method. NSI was added up to 1.5% in the K-CRG matrix. The prepared films were characterized for mechanical (tensile strength, tensile modulus, and elongation at break), thermal (differential scanning calorimetry, thermogravimetric analysis), barrier (water vapour transmission rate), morphological (scanning electron microscopy), contact angle, and crystallinity properties. Tensile strength, tensile modulus, and crystallinity were found to have increased by 13.8, 15, and 48% whereas water vapour transmission rate was found to have decreased by 48% for 0.5% NSI loaded K-CRG composite films. NSI was found to have formed aggregates for concentrations above 0.5% as confirmed by scanning electron microscopy. Melting temperature, enthalpy of melting, and degradation temperature of K-CRG increased with increase in concentration of NSI in K-CRG. Contact angle also increased with increase in concentration of NSI in K-CRG, indicating the decrease in hydrophilicity of the films improving its water resistance properties. This knowledge of the composite film could make beneficial contributions to the food and pharmaceutical packaging applications.

Super-Hydrophobic Surfaces Improve Corrosion Resistance of Fe3Al-Type Intermetallic in Seawater

2008 ◽  
Vol 47-50 ◽  
pp. 173-176 ◽  
Author(s):  
Tao Liu ◽  
Kin Tak Lau ◽  
Shou Gang Chen ◽  
Sha Cheng ◽  
Yan Sheng Yin
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Contact Angle ◽  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Hydrophobic Surface ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Atomic Force ◽  
Scanning Electron

A novel super-hydrophobic film was prepared by myristic acid (CH3(CH2)12COOH) chemically adsorbed onto the polyethyleneimine (PEI) coated Fe3Al-type intermetallic wafer. The film character and structure were probed with contact angle measurement, scanning electron microscopy (SEM) and atomic force microscope (AFM). The results suggest that the structure of the film is similar to lotus and the seawater contact angle is larger than 150◦. Moreover, the corrosion resistances of untreated and modified samples in seawater were investigated by electrochemical impedance spectroscopy (EIS). Experimental results show that the corrosion rate of Fe3Al-type intermetallic with super-hydrophobic surface decreases dramatically because of its special microstructure.

Effect of Plasma Gases on the Structure and Properties of WC-CrC-Ni Coatings

2015 ◽  
Vol 641 ◽  
pp. 105-110
Author(s):  
Maria Richert ◽  
Ilona Nejman ◽  
Marek Poręba ◽  
Jan Sieniawski ◽  
Łukasz Kuczek
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Light Microscopy ◽  
Plasma Spraying ◽  
Thermal Spray ◽  
Graphite Substrate ◽  
Structure And Properties ◽  
Porosity Of Coatings ◽  
Spraying Method ◽  
Scanning Electron

The effect of plasma gases (argon, helium) on the structure and properties of the WC-CrC-Ni coatings deposited at the graphite substrate has been investigated. The coatings were deposited by plasma spraying method in equipment Cham Pro –Thermal Spray Systems produced by Sulzer company. The microstructure of coatings were investigated by light microscopy (MO) and scanning electron microscopy (SEM). The performed investigations have been shown that with the increasing of amounts of argon and reducing volumes of helium and nitrogen, the microhardnees increased. The plasma gases also influenced on the porosity of coatings. Keywords: WC-CrC-Ni coatings, plasma spraying, microstructure, porosity Acknowledgement: The work was supported by project No INNOTECH – K2/IN2/9/181851/NCBR/13

scholarly journals WATER JET TECHNOLOGY AND SALT TREATMENT USED FOR CARROT STICKS.

HortScience ◽  
1992 ◽  
Vol 27 (6) ◽  
pp. 651f-651
Author(s):  
Yasuo Tatsumi ◽  
Alley E. Watada ◽  
Peter P. Ling
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Weight Loss ◽  
Water Jet ◽  
Nacl Solution ◽  
Salt Treatment ◽  
Textural Quality ◽  
White Tissue ◽  
Cut Surface ◽  
Scanning Electron

Water jet technology to slice carrots or salt treatment prior to slicing was studied to minimize the unappealing whitish tissue noted with carrot sticks. The water jet was a fine stream with 378,950 kPa force. Salt treatment consisted of immersing carrots in NaCl solution ranging from 0.0 to 1.0 M concentration for 3 to 20 hours. Subsequently, the carrots were sliced, stored at 5 C, and analyzed. Carrot sticks sliced with the water jet had a greater amount of white tissue than those sliced with a knife. Scanning electron microscopy showed that the water jet caused grooves on the cut surface, which exposed many layers of cells to dehydrate rapidly. The grooves probably can be minimized by increasing the speed of slicing. Salt treatments of 0.5 to 1.0 M concentration caused 3 to 10 percent weight loss when treated for 20 hours at 5 C or 3 hours at 20 C. Carrot sticks with increased weight loss had less whitish tissue and had an appearance of freshly cut sticks; however, the textural quality decreased.

scholarly journals Anti-Foulant Ultrafiltration Polymer Composite Membranes Incorporated with Composite Activated Carbon/Chitosan and Activated Carbon/Thiolated Chitosan with Enhanced Hydrophilicity

Membranes ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 827
Author(s):  
Syeda Samia Nayab ◽  
M. Asad Abbas ◽  
Shehla Mushtaq ◽  
Bilal Khan Niazi ◽  
Mehwish Batool ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Contact Angle ◽  
Activated Carbon ◽  
Bovine Serum Albumin ◽  
Bovine Serum ◽  
Carbon Composite ◽  
Flux Rate ◽  
Thiolated Chitosan ◽  
Scanning Electron

A rapid increase in population worldwide is giving rise to the severe problem of safe drinking water availability, necessitating the search for solutions that are effective and economical. For this purpose, membrane technology has shown a lot of promise but faces the challenge of fouling, leading to a reduction in its lifetime. In this study, ultrafiltration polyethersulfone membranes were synthesized in two different concentrations, 16% wt. and 20% wt., using the phase inversion method. Chitosan and activated carbon were incorporated as individual fillers and then as composites in both the concentrations. A novel thiolated chitosan/activated carbon composite was introduced into a polyethersulfone membrane matrix. The membranes were then analyzed using Attenuated Total Reflection–Fourier-Transform Infrared spectroscopy (ATR-FTIR), Scanning Electron Microscopy (SEM), optical profilometry, gravimetric analysis, water retention, mechanical testing and contact angle. For membranes with the novel thiolated chitosan/activated carbon composite, Scanning Electron Microscopy micrographs showed better channels, indicating a better permeability possibility, reiterated by the flux rate results. The flux rate and bovine serum albumin flux were also assessed, and the results showed an increase from 105 L/m2h to 114 L/m2h for water flux and the antifouling determined by bovine serum albumin flux increased from 23 L/m2h to 51 L/m2h. The increase in values of water uptake from 22.84% to 76.5% and decrease in contact angle from 64.5 to 55.7 showed a significant increase in the hydrophilic character of the membrane.

Single-stage electrospun innovative combination of polyurethane and neem oil: Synthesis, characterization and appraisal of blood compatibility

2018 ◽  
Vol 33 (6) ◽  
pp. 573-584 ◽  
Author(s):  
Mohan Prasath Mani ◽  
Saravana Kumar Jaganathan ◽  
Ahmad Zahran Khudzari ◽  
Rajasekar Rathanasamy ◽  
Praseetha Prabhakaran
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Contact Angle ◽  
Partial Thromboplastin Time ◽  
Blood Compatibility ◽  
Activated Partial Thromboplastin Time ◽  
The Novel ◽  
Neem Oil ◽  
Composite Patch ◽  
Scanning Electron

Wound healing is a complex process and it requires proper scaffolding for regeneration. An ideal scaffold should provide optimal environmental conditions in order to assist cellular attachment, proliferation and differentiation. In this work, a new composite based on polyurethane and neem oil was fabricated using one-step electrospinning technique. Fabricated composite patch along with the pristine polyurethane was characterized through scanning electron microscopy, Fourier transform and infrared spectroscopy, thermogravimetric analysis, contact angle measurement and atomic force microscopy. Moreover, the blood compatibility was evaluated using activated partial thromboplastin time, partial thromboplastin time and haemolysis assay. Scanning electron microscopy studies of composites revealed the existence of fibres with a smaller diameter (635  ± 105 nm) compared to the pristine polyurethane (969 ± 217 nm). Fourier transform and infrared analysis revealed the formation of hydrogen bond and peak shifting characteristics confirming the interaction of the neem oil with the polyurethane. Contact angle analysis showed the decrease in contact angle indicating the hydrophilic nature of the fabricated patch compared to pristine polyurethane. Thermal gravimetric analysis depicted the better thermal stability of the novel composite patch due to the existence of neem oil in the pristine polyurethane. The presence of neem oil in polyurethane matrix also resulted in an increase in the surface roughness as observed in the AFM analysis. The novel composite patch showed an ability to reduce the thrombogenicity and promoting the anticoagulant nature signified by blood compatibility assays like activated partial thromboplastin time and partial thromboplastin time. Finally, the haemolytic percentage of the fabricated composite (1%) was found to be reduced compared to control (2.733%) indicating better blood compatibility and safety with the red blood cells. Following the results, the fabricated patches offered enhanced physicochemical and blood compatible nature making it as a promising candidate for wound healing application.

Sign in / Sign up

Export Citation Format

Share Document