scholarly journals Time-Dependent Variations in Structure of Sheep Wool Irradiated by Electron Beam

2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Zuzana Hanzlíková ◽  
Michael Kenneth Lawson ◽  
Peter Hybler ◽  
Marko Fülöp ◽  
Mária Porubská
Keyword(s):  
Electron Beam ◽  
Secondary Structure ◽  
Tap Water ◽  
Absorbed Dose ◽  
Cysteic Acid ◽  
Conformational Composition ◽  
Large Variability ◽  
Dose Time ◽  
Time Variations ◽  
Usual Laboratory

Wool scoured in tap water with no special degreasing and containing a balanced humidity responding to usual laboratory conditions was irradiated by accelerated electron beam in the range of 0–350 kGy dose. Time variations of the wool structure were measured using FTIR, Raman, and EPR spectroscopy. The aim was to determine whether preexposure treatment of the wool, as well as postexposure time, affects the properties of the irradiated wool. Reactive products such as S-sulfonate, cystine monoxide, cystine dioxide, cysteic acid, disulphides, and carboxylates displayed a considerable fluctuation in quantity depending on both the absorbed dose and time. Mutual transformations of S-oxidized products into cysteic acid appeared to be faster than those in dry and degreased wool assuming that the present humidity inside the fibres is decisive as an oxygen source. EPR results indicated a longer lifetime for free radicals induced by lower doses compared with the radicals generated by higher ones. The pattern of the conformational composition of the secondary structure (α-helix, β-sheet, random, and residual conformations) also showed a large variability depending on absorbed dose as well as postexposure time. The most stable secondary structure was observed in nonirradiated wool but even this showed a small but observable change after a longer time, too.

scholarly journals Sheep Wool Humidity under Electron Irradiation Affects Wool Sorptivity towards Co(II) Ions

Molecules ◽  
2021 ◽  
Vol 26 (17) ◽  
pp. 5206
Author(s):  
Jana Braniša ◽  
Angela Kleinová ◽  
Klaudia Jomová ◽  
Róbert Weissabel ◽  
Marcel Cvik ◽  
...  
Keyword(s):  
Spectral Analysis ◽  
Electron Beam ◽  
Relative Humidity ◽  
Electron Irradiation ◽  
Absorbed Dose ◽  
Cysteic Acid ◽  
High Dose ◽  
Ftir Spectral Analysis ◽  
Common Laboratory ◽  
Sheep Wool

The effect of humidity on sheep wool during irradiation by an accelerated electron beam was examined. Each of the samples with 10%, 53%, and 97% relative humidity (RH) absorbed a dose of 0, 109, and 257 kGy, respectively. After being freely kept in common laboratory conditions, the samples were subjected to batch Co(II) sorption experiments monitored with VIS spectrometry for different lapses from electron beam exposure. Along with the sorption, FTIR spectral analysis of the wool samples was conducted for cysteic acid and cystine monoxide, and later, the examination was completed, with pH measuring 0.05 molar KCl extract from the wool samples. Besides a relationship to the absorbed dose and lapse, the sorptivity results showed considerable dependence on wool humidity under exposure. When humidity was deficient (10% RH), the sorptivity was lower due to limited transformation of cystine monoxide to cysteic acid. The wool pre-conditioned at 53% RH, which is the humidity close to common environmental conditions, demonstrated the best Co(II) sorptivity in any case. This finding enables the elimination of pre-exposure wool conditioning in practice. Under excessive humidity of 97% RH and enough high dose of 257 kGy, radiolysis of water occurred, deteriorating the sorptivity. Each wool humidity, dose, and lapse showed a particular scenario. The time and humidity variations in the sorptivity for the non-irradiated sample were a little surprising; despite the absence of electron irradiation, relevant results indicated a strong sensitivity to pre-condition humidity and lapse from the start of the monitoring.

scholarly journals Influences of Absorbed Dose Rate on the Mechanical Properties and Fiber–Matrix Interaction of High-Density Polyethylene-Based Carbon Fiber Reinforced Thermoplastic Irradiated by Electron-Beam

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 3012
Author(s):  
Se Kye Park ◽  
Dong Yun Choi ◽  
Duyoung Choi ◽  
Dong Yun Lee ◽  
Seung Hwa Yoo
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Carbon Fiber ◽  
Dose Rate ◽  
High Density Polyethylene ◽  
Absorbed Dose ◽  
High Density ◽  
Absorbed Dose Rate ◽  
Dose Rates ◽  
Absorbed Dose Rates

In this study, a high-density polyethylene (HDPE)-based carbon fiber-reinforced thermoplastic (CFRTP) was irradiated by an electron-beam. To assess the absorbed dose rate influence on its mechanical properties, the beam energy and absorbed dose were fixed, while the absorbed dose rates were varied. The tensile strength (TS) and Young’s modulus (YM) were evaluated. The irradiated CFRTP TS increased at absorbed dose rates of up to 6.8 kGy/s and decreased at higher rates. YM showed no meaningful differences. For CFRTPs constituents, the carbon fiber (CF) TS gradually increased, while the HDPE TS decreased slightly as the absorbed dose rates increased. The OH intermolecular bond was strongly developed in irradiated CFRTP at low absorbed dose rates and gradually declined when increasing those rates. X-ray photoelectron spectroscopy analysis revealed that the oxygen content of irradiated CFRTPs decreased with increasing absorbed dose rate due to the shorter irradiation time at higher dose rates. In conclusion, from the TS viewpoint, opposite effects occurred when increasing the absorbed dose rate: a favorable increase in CF TS and adverse decline of attractive hydrogen bonding interactions between HDPE and CF for CFRTPs TS. Therefore, the irradiated CFRTP TS was maximized at an optimum absorbed dose rate of 6.8 kGy/s.

scholarly journals Novel Organic Material Induced by Electron Beam Irradiation for Medical Application

Polymers ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 306 ◽  
Author(s):  
Adrian Barylski ◽  
Krzysztof Aniołek ◽  
Andrzej S. Swinarew ◽  
Sławomir Kaptacz ◽  
Jadwiga Gabor ◽  
...  
Keyword(s):  
Electron Beam ◽  
Electron Beam Irradiation ◽  
Absorbed Dose ◽  
Medical Application ◽  
High Energy ◽  
Polymer Chains ◽  
Degree Of Crystallinity ◽  
Beam Irradiation ◽  
The Impact ◽  
The Degree Of Crystallinity

This study analyzed the effects of irradiation of polytetrafluoroethylene (PTFE) containing 40% of bronze using an electron beam with energy of 10 MeV. Dosages from 26 to156 kGy (2.6–15.6 Mrad) were used. The impact of a high-energy electron beam on the thermal, spectrophotometric, mechanical, and tribological properties was determined, and the results were compared with those obtained for pure PTFE. Thermal properties studies showed that such irradiation caused changes in melting temperature Tm and crystallization temperature Tc, an increase in crystallization heat ∆Hc, and a large increase in crystallinity χc proportional to the absorbed dose for both polymers. The addition of bronze decreased the degree of crystallinity of PTFE by twofold. Infrared spectroscopy (FTIR) studies confirmed that the main phenomenon associated with electron beam irradiation was the photodegradation of the polymer chains for both PTFE containing bronze and pure PTFE. This had a direct effect on the increase in the degree of crystallinity observed in DSC studies. The use of a bronze additive could lead to energy dissipation over the additive particles. An increase in hardness H and Young’s modulus E was also observed. The addition of bronze and the irradiation with an electron beam improved of the operational properties of PTFE.

scholarly journals Some Properties of Electron Beam-Irradiated Sheep Wool Linked to Cr(III) Sorption

Molecules ◽  
2019 ◽  
Vol 24 (23) ◽  
pp. 4401 ◽  
Author(s):  
Jana Braniša ◽  
Angela Kleinová ◽  
Klaudia Jomová ◽  
Radka Malá ◽  
Volodymyr Morgunov ◽  
...  
Keyword(s):  
Electron Beam ◽  
Absorbed Dose ◽  
Concentrated Solutions ◽  
Octahedral Structure ◽  
Fiber Volume ◽  
Optimized Conditions ◽  
Higher Doses ◽  
Charge Point ◽  
Sheep Wool

We examined the characteristics of an electron beam irradiated wool with an absorbed dose of (21–410) kGy in comparison with natural wool with respect to the determination of the isoelectric point (IEP), zero charge point (ZCP), mechanism of Cr(III) sorption from higher concentrated solutions, and the modelling of the wool-Cr(III) interaction. The data of ZPC and IEP differed between natural and irradiated samples. Increasing the dose shifted the pH of ZPC from 6.85 for natural wool to 6.20 for the highest dosed wool, while the natural wool IEP moved very little, from pH = 3.35 to 3.40 for all of the irradiated samples. The sorption experiments were performed in a pH bath set at 3.40, and the determination of the residual Cr(III) in the bath was performed by VIS spectrometry under optimized conditions. The resulting sorptivity showed a monotonically rising trend with increasing Cr(III) concentration in the bath. Lower doses, unlike higher doses, showed better sorptivity than the natural wool. FTIR data indicated the formation of complex chromite salts of carboxylates and cysteinates. Crosslinks via ligands coming from different keratin chains were predicted, preferably on the surface of the fibers, but to a degree that did not yet inhibit the diffusion of Cr(III)-cations into the fiber volume. We also present a concept of a complex octahedral structure.

Sorption properties of sheep wool irradiated by accelerated electron beam

2016 ◽  
Vol 70 (9) ◽  
Author(s):  
Zuzana Hanzlíková ◽  
Jana Braniša ◽  
Peter Hybler ◽  
Ivana Šprinclová ◽  
Klaudia Jomová ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Electron Beam ◽  
Secondary Structure ◽  
Sorption Capacity ◽  
Active Sites ◽  
Low Doses ◽  
Amino Groups ◽  
Structure Variation ◽  
Carboxylic Groups ◽  
Sheep Wool

AbstractElectron beam (EB) irradiated wool was examined for sorption of chromic ions. Sorption increased with the adsorbed dose non-monotonously, which is a result of the generation of S-oxidized groups, secondary structure variation, and the breaking of the keratin backbone. For a dose of 400 kGy, an increase by 120 % was observed at the cystine dioxide and cysteine acid amounts. Examining sorption of unexposed wool and that irradiated with doses of 25 kGy and 40 kGy for basic, methylene blue (MB), or acidic, pyrogallol red (PR) dyes revealed that such low doses have no effect on the carboxylic or amino groups of keratin. Sorption of MB is independent of the EB treatment and is identical for both samples due to the interaction of MB amino groups with the carboxylic groups of wool; however, the sorption capacity for PR is a function of the EB treatment. The sample irradiated with the dose of 25 kGy showed higher PR sorption than that with the EB dose of 40 kGy, which was equal to that of unexposed wool. While the 25 kGy sample provided more active sites for PR interaction compared with the unexposed one, the 40 kGy sample contained already enough active sites to generate intra- and intermolecular interactions inside wool. Thus, PR adherence to the 40 kGy sample was restricted and comparable to the level of unexposed wool.

scholarly journals Nanoparticles synthesis by electron beam radiolysis

2014 ◽  
Vol 12 (7) ◽  
pp. 774-781 ◽  
Author(s):  
Ioan Călinescu ◽  
Diana Martin ◽  
Daniel Ighigeanu ◽  
Adina Gavrila ◽  
Adrian Trifan ◽  
...  
Keyword(s):  
Silver Nanoparticles ◽  
Electron Beam ◽  
Chemical Reduction ◽  
Absorbed Dose ◽  
Reduction Process ◽  
High Dose Rate ◽  
High Dose ◽  
Experimental Conditions ◽  
Dose Rates ◽  
Absorbed Dose Rates

AbstractElectron beam (EB) irradiation is a useful method to generate stable silver nanoparticles without the interference of inherent impurities generated from chemical reactions. Our experiments were carried out using linear electron beam accelerators with two different EB absorbed dose rates: 2 kGy min−1 and 7–8 kGy s−1, and with different absorbed dose levels. The optimum conditions for silver nanoparticles (AgNPs) generation by radiolysis, or by radiolysis combined with chemical reduction, were established. In order to obtain a good yield for AgNPs synthesized by radiolysis, a high dose rate is required, resulting in a rapid production process. At low absorbed dose rates, the utilization of a stabilization agent is advisable. By modifying the experimental conditions, the ratio between the chemical and radiolytic reduction process can be adjusted, thus it is possible to obtain nanoparticles with tailored characteristics, depending on the desired application.

Sign in / Sign up

Export Citation Format

Share Document